CommScope OneCell RP Series Bedienungsanleitung

Outdoor Radio Point Installation

Document Number: 913032

Document Revision: 1.04

Date: February 2016

OneCell®

What’s in the box

The outdoor Radio Point (RP) ships with the following hardware:

• Radio Point with mounting plate and brackets attached

• Four mounting screws (M5 x 10mm)

• RJ45, IP67 connector

• Two N-type antenna couplers

Mounting the Radio Point (RP) on a pole requires the following hardware provided by

the system integrator:

• Two adjustable clamps

Mounting the Radio Point (RP) on a wall requires the following hardware provided by

the system integrator:

• Four molly screws capable – 50 lb (23 kg) minimum rating

Before installing the RP on the pole, terminate the RP end of the Ethernet cable with

the RJ45, IP67 connector provided in the box.

NOTE

For more information on installing Radio Points, see OneCell Installation and

Commissioning (913025).

Pole mount installation

NOTE

The minimum pole diameter requirement is 4'' (102mm).

1Slide the adjustable clamp through the slots on each RP mounting bracket on the

RP plate.

Slide adjustable

clamp end

through slots

2Wrap each clamp around the pole and tighten the clamp screw to secure the RP to

the pole.

3Insert two screws into the upper holes on opposite sides of the RP as shown in the

drawing below.

Insert screws

into the holes

called out – one

on each side.

4Hang the RP to the mounting bracket using the installed screws. Align holes at

bottom location of bracket and install two additional screws. Tighten all four

screws.

5Insert and tighten the bottom screws through the plate hole into both sides of the

RP.

6Connect the antenna couplers on the top of the RP.

7Connect the Ethernet cable RJ45 end to the bottom of the RP.

Installation complete. To configure the RP, see the commissioning procedures in

OneCell Installation and Commissioning (913025).

Antenna couplers

Ethernet connector RJ45

Bottom screw

Wall mount installation

1Remove the brackets from the back of the mounting plate.

2Drill four holes in the wall using the mounting plate to determine the hole

locations. Mount the backplate on the wall with four molly screws.

3Insert two screws into the upper holes on opposite sides of the RP as shown in the

drawing below.

4Attach the RP to the mounting plate. Tighten the screws on the RP.

Insert screws

into the holes

called out – one

on each side.

5Insert and tighten the bottom screws through the plate hole into both sides of the

RP.

6Connect the antenna couplers on the top of the RP.

7Connect the Ethernet cable RJ45 end to the bottom of the RP.

Installation complete. To configure the RP, see the commissioning procedures in

OneCell Installation and Commissioning (913025).

Antenna couplers

Ethernet connector RJ45

Bottom screw

Inhaltsverzeichnis

Andere CommScope Konferenzsystem Handbücher

CommScope

CommScope SYSTIMAX iPatch Panel Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung