CommScope SYSTIMAX MGS Series Bedienungsanleitung

SYSTIMAX®Solutions www.commscope.com

Instruction Sheet 860344274

Issue 10,October 2019 Rev B

SYSTIMAX



MGS Module Termination Instructions

General

These instructions provide the recommended termination procedure for all SYSTIMAX®MGS-type modules.

MGS600 modules are illustrated here, but instructions also apply to MGS400 and MGS500 modules. The MGS

modules are UL approved. Preparation of the new SYSTIMAX GigaSPEED®X10D 91B series cable,95B

series cordage, or 91SD series cable is also shown. For complete instructions on prepping the

GigaSPEED X10D 91B series cable,95B series cordage or 91SD cable for termination, see instruction

sheet 860 469 402. Refer to the SYSTIMAX X10D Design and Installation Guidelines for further

information.

The following tools are available to aid in module termination.

Material ID

406477794

407484971

407728427

760122713

860251081

Description

D-914 kit - includes impact tool and 110 blade

D-914 impact tool only

Replacement 110 blade for D-914 impact tool

Module removal tool (quantity of 5)

Hand termination tool (hand puck)

How to Contact Us

•To find out more about CommScope® products, visit us on the web at http://www.commscope.com/

•For technical assistance:

-Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or Authorized

Business Partner.

-Within the United States, report any missing/damaged parts or any other issues to CommScope

Customer Claims at 1-866-539-2795. Outside the United States, contact your local account

representative or Authorized Business Partner.

Preparation ofX10D 91B Series Cable, 95B Series Cordage, or91SD Series Cable

for Termination

Thisproductiscovered byone or more of the following U.S. patents : 5.997.358 / 5.1.86.647 / 5.897.395

Pull flute and tapes

off to one or more sides

Unwind separator tape

Pull off to the side so that it can

be trimmed close to the jacket

860344274

Instruction Sheet www.commscope.com

Page 2 of 5

Termination Procedure

T568B Wiring Shown

Pre-Termination Step For Angled Entry

Note: Some mounting hardware and box space does not

allow for cable entry directly from the rear. If a typical

termination from the rear is done and the cable is then bent

in the needed direction, performance and reliability can

suffer. A proper termination should have the intended entry

direction set before seating the conductors.

1. Set the intended entry angle before seating the

conductors.

2. Pull pairs into the module until the jacket is snug

against the rear housing. Outer pairs should sweep

around the inside pairs and not be pulled into them.

Direct Cable End Reverse Cable End

Orange pair

Green pair Brown pair

(Blue pair)

(Brown pair) (Orange pair)

(Green pair)

Blue pair

1. Each cable end has two pairs routed into the holes and two pairs routed over the top, without crossover or

rearrangement. On the Direct cable end, the Orange and Blue pairs enter the holes and the Green and

Brown pairs lay over the top. On the Reverse cable end, the Green and Brown pairs enter the holes and the

Orange and Blue pairs lay over the top.

2. Pull pairs into the module until the jacket end is snug against the rear housing.

Cable positioned at 90

prior to seating conductors

www.commscope.com

860344274

Issue 9,October 2019

Page 3 of 5

3. To place conductors, hold the pair down on the

termination position and bend it for easy grasp as

shown above. Then untwist the pair in a counter-

clockwise direction enough to open it up.

4. Push conductors down into slot

positions (check color codes).

Maintain pair twist up to the

opening for the slots.

Orange pair

Blue pair

Green pair

Brown pair

Ensure that front pairs

are tightly routed

5. (T568B wiring shown) On the Direct cable end, place Orange and Blue pairs first, then place Green and

Brown pairs.

Orange pair

Blue pair

Green pair

Brown pair

Ensure that front pairs

are tightly routed

6. (T568B wiring shown) On the Reverse cable end, pull Green and Brown pairs back, eliminate the twist, and

pull them tightly into place. Then route Orange and Blue pairs to the front positions.

860344274

Instruction Sheet www.commscope.com

Page 4 of 5

Note: For T568A Wiring -

On each cable end, one of the two pairs fed in through the holes is pulled back for the rear positions. Check

label color codes.

Conductor Seating and Cutting

Impact tool on HI setting

with M110 cutting blade

Hand puck

Pliers

Trim pairs

flush

Fine edge

cutters

1. Use impact tool on HI setting with M110

cutting blade

to punch conductors

straight down into slots. When using the

impact t

ool, the hand puck is

recommended.

2. Use pliers with wire cap to seat

conductors. Use fine edge cutters to

trim conductors flush to the module

body.

Module Removal

1. To remove a module for inspection or

repair, insert prongs of removal tool into

openings at sides of module and press

firmly.

The module wiring cap can also be used to

remove a module. Insert prongs of cap into

openings at sides of module and press

firmly.

2. The module can then be removed from the

back.

Removal tool

860344274

Issue 9,October 2019

Page 5 of 5

www.commscope.com

Inspection or Repair of Termination

Note: To enable inspection or repair, the wiring

cap can be released from the module using the

removal tool. The conductors can then be

removedfor repair.

1. Insert end of removal tool into slot under

wiring cap and pivot it forward to release

cap.

Insert end of tool into

slot under wiring cap

Pivot removal tool forward

to disengage cap

Slot

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Steuereinheit Handbücher

CommScope

CommScope Ruckus I100 Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-1100-E-GS3-1U-24 Bedienungsanleitung

CommScope

CommScope ION-U H 17P2 Bedienungsanleitung

CommScope

CommScope Propel PPL-1U-HD-FX Bedienungsanleitung

CommScope

CommScope CMOD Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 InstaPATCH 3603M UHD Bedienungsanleitung

CommScope

CommScope FlexWave Host Unit II Stücklistenhandbuch

CommScope

CommScope FTTX Solutions Rapid Flexible Fiber Box Bedienungsanleitung

CommScope

CommScope ATSBT-4G Series Bedienungsanleitung

CommScope

CommScope ION-M7HP EU Bedienungsanleitung

CommScope

CommScope NG4access ODF Platform Value-Added Module Bedienungsanleitung

CommScope

CommScope Teletilt ATC200-LITE-USB Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung