CommScope FOSC-400A4 Bedienungsanleitung

FOSC-400A4

INSTALLATION INSTRUCTION

Fibre Optic Splice Closure with

integrated organiser system

TC-441-IP

Rev A, Mar 2017

www.commscope.com

1 General

1.1 The installation instruction describes the

necessary steps to install the

FOSC-400A4. The used optical fiber cables

may consist of a loose tube, slotted core,

central core or ribbon construction depending

on the type of FOSC kit. Illustrated are the

loose tube construction and fusion splicing

protected by

heat-shrinkable splice protectors.

1.2 The FOSC-400A4 kit is supplied with

one splice tray organizer. One tray (S16)

can accommodate up to 16 fiber splices,

depending the type of tray. A second tray kit

may be used (maximum 2 trays per closure).

1.3 All splice trays accommodate fusion

splice protection types such as Raychem

SMOUV-1120-serie and some types of trays

(S12) most common types of mechanical

splices.

(GTE, FIBRLOK or other similar products).

1.4 FOSC-400A4 closure system has one

oval cable entry port which can handle 2

cables e.g. looped cable and four small

circular ports.

1.5 The seals may only be installed with

hot air (hot-air temperature should be at least

350°C). An open flame is not allowed.

1.6 The FOSC-400A4 can be installed in

direct buried, manholes or aerial locations.

1.7 The kit contents listed in this installation

instruction reflect the standard contents.

Alternative configurations are possible.

2 Product description

2.1 Product designation

Ex. FOSC-400A4-S08-2-NNN-S6007

A4 A version with 4 round ports

S08 Tray for up to 8 stacked splices

1 Closure is delivered with 1 tray

NNN No blocking, pressure valve and grounding needed

S6007 Customer control number

Raychem Total Outer dia Max. fusion Cable diameter in

description closure length closure splice Circular Oval

capacity port port

Min. Max. 250µ Min. Max. Min. Max.

(body) (body fibers (*) (*) (**) (**)

+ clamp)

FOSC-400A4 420 152 205 32 5 19 10 25

FOSC-400B2 540 152 205 96 5 32 10 25

FOSC-400B4 540 152 205 96 5 19 10 25

FOSC-400D5 710 240 285 576 5 32 10 25

FOSC sizing information (dimensions in mm)

(*) Cable diameter for 1 cable/port

(**) Cable diameter for 2 cables/port

Number of organizer

trays in kit.

A closure:0-2

B closure:0-4

D closure:0-8

Ground feed thru lug(s)

G = Grounding

N = None

Raychem Customer

Specification Nnumber

Closure size: A, B or D

Number of round ports

Type of tray

S: only mentioned if it

is the tray, with Stacked

splices (EUR design).

There is no indication

if the splice modules are used

(US design).

Splice capacity of

each organiser tray:

A Tray: 08 or 16

B Tray: 12, 16 or 24

D Tray: 36, 48 or 72

No trays = NT

Cable Blocking

Components

B = Blocking

N = None

Valve for flash

Test

V = Valve

N = None

FOSC-400X X - X X X - X - X X X - X X Y Y

• Dome

• Clamp

• Base with strength member connections

and one tray assembly (see 2.3.1.)

• Loose tube storage sleeve

• Oval outlet seal kit (see 2.3.3.)

• Installation instruction

• Sealing ring

2.3.1 Tray kit

FOSC-A-TRAY-SO8-1

• Tray for 8 splices

• Tray lid

• Tie-wraps

• 4 large transportation tubes

(id=2,8 mm)

• Tray support wedge

2.3 Examples of supplementary kits

2.3.2 Cable seal-kit

FOSC-A-CSEAL-1-NT

• Aluminium cable protection tape

• Heat-shrinkable cable sleeve

• Cleaning tissue

• Abrasive strip

• 1 Screw and 1 washer for the strength

member attachment

* Installation instruction*

2.3.3 Oval outlet cable seal kit

FOSC-A-CSEAL-2-NT

• Heat shrinkable sleeve

• Branch-off clip

• Aluminium cable protection tapes

• Abrasive strip

• Cleaning tissues

• 2 Screws and 2 washers for the

strength member attachment

* Installation instruction*

* Only included if the seal kits are ordered

separately.

2.2 Content FOSC-400A4-XXX-1-NNN

2.3.4 Re-entry kit

FOSC-D-O-RING-SEAL-KIT

• Desiccant

• Sealing ring

• Cleaning tissue

2.4 Accessory kits

2.4.1 FACC-HEAT-GUN-220V

Hot air gun CV 1981 (1460 Watt) and

Reflector PR 26.

Min. required hot-air temperature: 350°C.

2.4.2 FOSC-A/B-POLE-MOUNT.

Mounting kit

Accessories for pole mounting or wall fixing.

2.4.3 FOSC-A-SHIELD-CON-KIT

- Shield continuity wires (6 pcs)

- Shield continuity connectors (5 pcs)

2.4.4 FOSC-A/B-VAULT-BAG

Flame retardant bag to cover closure for vault

application.

2.4.5 FOSC-WORK-STAND

FOSC holder device

4.3 Remove any dirt, mud or other

contaminants from the cable sheath for

approximately 2 meters with a clean cloth.

Take the oval cable seal and slide it over the

cables. The non-coated edge of the sleeve

and the arrows should be pointed to the base

of the closure.

4.2 Install the FOSC in the FOSC-STAND

and open the oval port for cable entry by

cutting the port at the ridge with a hacksaw.

Deburr the inner edge of the port opening

with abrasive strip.

4.1 Loose the clamp.

Push the lever down to release the locking tab.

Open the clamp lever and release the clamp

using the lever legs.

Remove the clamp, dome and sealing ring

and store carefully for later use.

3 General precautions

3.1 Do not use damaged sleeve nor trim

heat-shrinkable sleeve before installation.

3.2 The FOSC-400A4 closures can be

installed at temperatures between -1°C and

+45°C.

3.3 Generators used should have enough

capacity for the hot air gun utilisation.

Optical fiber infrastructure network

elements may contain end of optical fiber

attached to the optical output when the

device is operational. Laser radiation can

seriously damage your eyesight. Please

follow your local safety guidelines.

4 Cable installation in oval

outlet

4.4 Slide the cables through the opened

oval port. Prepare cables as described in

section 5 (cable preparation).

5.2 Order the FOSC-A-SHIELD-CON-KIT if a

shield continuity is required. Cut cable

sheath axially for 25 mm from cable ring cut.

Crimp shield clip on cable sheath with pair

of pliers.

Protect the clip with self adhering tape.

5.3 Cut the loose tube, at a distance of

35 mm from the cable ring cut and remove

and degrease fiber bundle. Select a

transportation tube which fits over the loose

tube. Slip transportation tube over fibers and

the loose tube.

Note: for slotted core cable: use an

appropriate kit which converts the slotted

cable construction into a loose tube

construction.

5.1 Remove the cable sheath (and shield if

present) over a length as required by locally

approved practice (e.g. 1,2 meters). 1.1 m

is the maximum allowed length if the ribbon

(4R4) or high capacity trays (S16) are used.

Clean filling compound from fiber tubes and

cut central strength member at a distance of

75 mm from outer jacket.

5 Cable preparation

6.1 Thoroughly clean oval port and cable

sheath with the cleaning tissue over a

distance of 100 mm from the edge of the

port.

6.2 Abrade oval port and cable sheath

circumferentially on the cleaned area with the

abrasive strip. Remove any abraded material

with a clean cloth.

6.3 Place oval seal over the oval port and

cable. Mark the sleeve length onto the cable.

5.4 Align cable ring cuts with edge of

base.

5.5 Install the screw and washer into the

strength member fixation device. Slide the

cable strength member under the washer and

tighten the screw. Cut the excess length of the

cable strength member.

5.6 If required, connect shield continuity

wire of both cables with shield continuity

clip. Talk pairs, if present, will be connected

together according to the local procedures.

6 Sealing of oval outlet

Strenght

member Cable ring cut

Cable

6.7 Shrink down the end of the sleeve on

the cable side. Heat until the sleeve shrinks

down on the cables and take care that the

green thermo-indicating paint is converted to

black. Postheat the clip on both sides till the

adhesive shows a proper flow on the clip

between the two cables.

Wait until the sleeve is cool to the touch

before moving the cables.

6.6 Shrink the oval cable seal on the FOSC-

base side with the recommended hot air gun

device with reflector. Shrink sleeve until the

green thermo-indicating paint is converted to

black. (Make sure the hot-air temperature is at

least 350°C).

(If a FACC-HEAT-GUN-220V is used, set

position on scale 10).

6.4 Match the blue line of the aluminium

cable protection foil with the marks on the

cables. Wrap aluminium cable protection foil

around cable.

6.5 Slide the oval cable seal over the oval

port. Install the branch-off clip. Check that

the heat-shrinkable sleeve butts up against

the FOSC-base and the branch-off clip is

completely inserted. Tape the two cables

together.

Splicing and fiber storage

7.1.3 Position the FOSC-400A4 by the

splicing machine in a convenient location,

and secure the closure.

7.1.4 Slide the heat-shrinkable splice

protection over one fiber and fuse fibers

according to local recommendations and

procedures. After the fusion splice is made,

install the heat-shrinkable splice protection

(e.g. SMOUV) with appropriate heating

source. Allow the splice protection to cool

down to ambient temperature.

7.1.1 Each splice tray accommodates 8 fiber

splices maximum and each side of the tray

holds a maximum of 4 big transportation

tubes.

Position the transportation tubes on bottom

tray and align the tubes along the tray. Place

a mark on each tube on tray side at 15 mm

from tray edge.

7.1.2 Carefully cut the transportation tubes at

the mark and secure to splice tray with two tie

wraps. The transportation tube may not be in

contact with fibers stored in the organizer.

7.1.5 After each splice is made, the splice

should be stored in the splice holder. Do not

deform the splice protector during insertion.

The fiber slack should be coiled into the tray.

7 Organization of the fibers

7.1 If a FOSC-A-TRAY-S08-1 is used. Tray

for up to 8 splices

Inhaltsverzeichnis

Andere CommScope Industrieanlagen Handbücher

CommScope

CommScope DryLine MT Series Bedienungsanleitung

CommScope

CommScope FMT-D Bedienungsanleitung

CommScope

CommScope DryLine ODPMT200 Series Bedienungsanleitung

CommScope

CommScope DryLine PMT200B Series Bedienungsanleitung

CommScope

CommScope NG3 Bedienungsanleitung

CommScope

CommScope OMX 600 Splice Bay Bedienungsanleitung

CommScope

CommScope TFAH-ES70 Bedienungsanleitung

CommScope

CommScope NOVUX DSC 650 Bedienungsanleitung

CommScope

CommScope OMX Bay System Benutzerhandbuch

CommScope

CommScope HELIAX FiderFeed DFJ-4S112B Bedienungsanleitung

CommScope

CommScope 864 FDH RESKIN KIT Bedienungsanleitung

CommScope

CommScope FIST-RSKG-16 Bedienungsanleitung

CommScope

CommScope FIST-GSS2 Bedienungsanleitung

CommScope

CommScope EPX G2 Bedienungsanleitung

CommScope

CommScope ADCP-90-326 Bedienungsanleitung

CommScope

CommScope ION-M7P/17EHP Bedienungsanleitung

CommScope

CommScope FACT Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung