CommScope RUCKUS H550 Bedienungsanleitung
H550 Surface Mount Bracket
Quick Setup Guide
This Quick Setup Guide provides step-by-step instrucons on how to install
the H550 access point (AP) using the oponal surface mount bracket. The
H550 Surface Mount Bracket (Part # 902-0136-0000) is designed to mount
the H550 AP on a wall surface that does not have an in-wall cable roung
box.
Package Contents
Verify that all of the following items are included in the package. If any
item is damaged or missing, nofy your authorized RUCKUS sales
representave.
•One H550 surface mount bracket
•Two torx mounng screws
•This Quick Setup Guide
Required Hardware and Tools
•One RUCKUS H550 wall switch AP
•A T8 Torx driver
•Customer-supplied mounng screws and plasc wall anchors
•An electric drill with drill bits
•A screwdriver with assorted bits
Mounng the AP with the Surface Mount Bracket
1. Use the surface mount bracket as a template to mark the locaons for
drill holes (four mounng hole locaons).
FIGURE 1 Surface Bracket Mounng Holes
1. Mounng holes
2. Drill holes of the appropriate size for the customer supplied mounng
screws and plasc wall anchors.
3. If you will be running the uplink Ethernet cable through the boom of
the surface bracket, remove one of the punch-out tabs at the boom
of the surface bracket.
4. Aach the bracket to the wall using the plasc wall anchors and
mounng screws.
5. Run the Ethernet uplink cable through the punch-out tab opening in
the boom of the surface bracket (or through the large hole in the
center of the surface bracket).
6. Remove the two torx screws from the sides of the H550.
FIGURE 2 Removing Torx Screws from AP
1. Torx screws
7. Remove the at mounng bracket from the back of the AP. This
bracket will not be used when using the surface mount bracket.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 1 of 2
Published November 2020, Part Number 800-72521-001 Rev A
FIGURE 3 Removing Flat Bracket from Rear of AP
8. Connect the uplink cable to the LAN 5/PoE In port of the H550.
9. The surface bracket has two lower hooks that t into slots on the
boom of the H550. Rest the boom of the H550 on the hooks, and
lt the H550 toward the wall unl it is up against the surface bracket.
10. Tilt the H550 toward the wall unl it is up against the surface bracket.
FIGURE 4 Mounng the H550 to the Surface Bracket
11. Use a T8 Torx driver to screw the two torx mounng screws from the
bracket kit into the sides of the H550 and through to the threaded
inserts on the sides of the mounng bracket.
Congratulaons! You have completed mounng the H550 using the
surface bracket mounng kit.
© 2020 CommScope, Inc. All rights reserved.
ARRIS, the ARRIS logo, COMMSCOPE, RUCKUS, RUCKUS WIRELESS, the Ruckus
logo, and the Big Dog design are trademarks of CommScope, Inc. and/or its
aliates. Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Cered, the Wi-Fi
CERTIFIED logo, Wi-Fi Protected Access, the Wi-Fi Protected Setup logo, Wi-Fi
Protected Setup, Wi-Fi Mulmedia and WPA2 and WMM are trademarks or
registered trademarks of Wi-Fi Alliance. All other trademarks are the property of
their respecve owners.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 2 of 2
Published November 2020, Part Number 800-72521-001 Rev A
Andere CommScope TV-Halterung Handbücher
