Compumatic xl1000 Bedienungsanleitung
CALCULATING TIME RECORDER
USER’SMANUAL
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
TABLE OF CONTENTS
1. INTRODUCTION…………………………………………………….1
2. FEATURES ………………………………………………………….2
3. PREPARATION……………………………………………………… 3
(1) Structure …………………………………………………………. 3
(2) Installation………………………………………………………… 4
4. DAILY OPERATION ………………………………………………… 5
5. QUICK EASY SETUP ……………………………………………… 6
6. SETTING THE TIME………………………………………………... 7
7. SETTING THE DATE……………………………………………….. 8
8. SETTING TIME SYSTEM…………………………………………... 9
9. SETTING PRINT FORMAT........................................................ 10~14
10. SETTING THE TIME OF DAY CHANGE………………………….. 15
11. SETTING THE COMMON SCHEDULE..…………………………16~23
12. SETTING THE EXTRA SCHEDULE…..………………………….24~34
13. SETTING THE ROUNDING PUNCH..……………………………35~36
14. SETTING THE DAYLIGHT SAVING TIME..................................37~40
15. SETTING THE PRINT LANGUAGE………………………………... 41
16. SETTING THE BUZZER PERIOD………………………………….. 42
17. SETTING THE VERTICALADJUST………………………………... 43
18. TIME CARD NUMBER TRANSFER………………………………... 44
19. TIME CARD NUMBER DELETE…………………………………….45
20. PRINT SAMPLE……………………………………………………..46~49
21. RESET………………………………………………………………….50
22. REPLACING THE RIBBON CARTRIDGE………………………….51
23. CONNECTING THE EXTERNAL TIME SIGNAL (OPTIONAL)….. 52
24. INSTALLING THE BATTERY PACK (OPTIONAL)………………… 53
25. TROUBLESHOOTING……………………………………………….. 54
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
1. INTRODUCTION
1. The details of this User’s Manual are subject to change without prior notification.
2. This User’s Manual has been prepared with the utmost care to cover all aspects
of the time recorder’s use. However, if there are some explanations that are
inadequate, unclear, or difficult tounderstand, please do not hesitate to contact
the dealer or the store from which you have purchased your Time Recorder.
3.Be sure to use your Time Recorder after you have fully understood the hardware,
software specifications and limits.
SPECIFICTIONS
●Power Supply: AC 100V~240V 50/60Hz
●Power Consumption: Normal 0.8W (Max.15W)
●Standard time signal: Quartz oscillation
●Clock accuracy: Monthly accuracy ±15sec. (at ordinary temperatures)
●Printing system: Dot matrix.
●Power failure compensation: Threeyears of cumulative power failure hours after
the date of shipment.
●Print at power failure: Optional battery pack, 200-time printing or 24 hours.
●Operating environment: Temperature:-5to 45, 23to 113.
Humidity: 20% to 80% (no condensation).
The unit operates normally at temperatures of 5or
below, but the print density, reaction of the LCD display,
and the numbers of prints are inferior to those at normal
operation temperature.
●Dimensions: 7.91”(H) X 6.02”(W) X 4.64”(D)
201mm (H) X 153mm (W) X 118mm (D)
●Weight: Approx, 3.1 lbs. (1.4Kg)
●Accessories: Operation manual: 1 copy
Fuses: 1 pc. Keys: 2 pcs.
1
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
2. FEATURES
●This unit has two work type that can be selected (employee and part-time).
●This unit has the ability to calculate elapsed time between IN/OUT
punches.
There are two calculation mode, (punch and hourly) that can be selected.
●In Employee mode, you can punch IN/OUT as many times as required per
day.
●Automatic IN/OUT column shift when you punch.
●In Employee mode, you can select one of three pay period:
Monthly/ Weekly/ Bi-Weekly.
●Two types of schedules can be programmed:
Common schedule/ Extra schedule.
●Amaximum of 50 cards can be automatically registered.
●Special mark printing can be set to make it easy to trackemployee’s, late in
or early out.
●The language of English, Spanish, Germany, French, Italian, Portuguese
can be selected to print the day of the week.
●Security for power failure
(1) Optional battery pack ensuresfull printing operation after power failure.
(2) When the battery voltage drops too low for a print to be produced, the LCD
display goes out. Both time and programsare retained by a lithium battery
for approx. 36 months.
(3) After power is restored, the time recorder will automatically advance
to the present time.
●Midnight button
For nightshift workers, when punch time is over the printing line time,press the
“Midnight button”then punch the time card. The time will be entered in the
“OUT”column of the previous day.
* On pay ending day, the “Midnight button”will be of no use.
●Time display
Easy-to-read, back light L.C.D. It shows date, AM/PM (when set to 12-hour
system), time, day of week and other codes.
●Automatic Day Light Saving Time
2
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
3. PREPARATION
(1) Structure
Front view Back view
Display
3
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
(2) Installation
●Power Source
1) Use a power source with a stable voltage.
2) Use a power source which is independent from other equipment.
●Installation
Avoiding installing the machine in any of the following places:
1) Subject to high humidity and dust.
2) Exposed to strong or continuous vibrations.
3) Exposed to direct sunlight.
“CAUTION”: DISCONNECT POWER SUPPLY CORD BEFORE
OPENING HOUSING.
“WARNING”: EXPLOSING HAZARD - DO NOT USE
NON-RECHARGABLE BATTERIES.
(3) Wall Mounting
1) Place 2 screws into a wall 3.94 inches (10cm) apart. Be sure to keep
approx. 0.12 inch (3mm) of the screw head protruding from the wall.
2) Hook the unit on to the screws through the holes of the back cover, as
shown in the figure.
* Please note position of security hole (located above the left fixing hole).
Installation: Remove lid, mark position of hole onto the wall, remove
machine, drill, fit wall plug, refit machine to wall, enter security screw into
position and replace lid.
4
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
4. DAILY OPERATIONS
●When the power cord is plugged in, the time recorder can be used immediately
with the basic functions. The basic functions includethe work type (employee),
pay period (monthly) and pay ending day (31).
●In employee mode, when a new time card is inserted to the time recorder, the
time card will be registered automatically, and will print in “IN”position on the first
line.
●In employee mode, you can punch “IN”and “OUT”as many times as you want
per day, the time recorder will memorize the last punch, and automatically switch
to “IN”or “OUT”position.
●You can change the “IN”or “OUT”position by pressing the “IN”or “OUT”button.
●If punched in “OUT”position when the work time is over the “printing line time”,
by pressing the “midnight button”and then making a punch, it will imprint “IN”
and “OUT”on same printing line, otherwise the imprint will be in the “IN”position
on the next printing line.
*On pay ending day, the “Midnight button”can not be used.
5
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
5. QUICK EASY SETUP
6
(1) Plug the Ac cord into the Ac
outlet.
*The socket-outlet should be
installed near the equipment and
should be easily accessible.
(3) Unlock with key and remove the
top cover.
(4) When program settings are
completed, replace the top
cover and lock.
(2) Remove the protection pad.
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
6. SETTING THE TIME
Example: Change the time from PM 10:20 to AM 11:30
-
7
(1) Press the [F] button, and
position the “▲”under the
“TIME”mark. The “Hour”
flashes (The flashing
means it can be changed).
FE
TIME
Hour Minute
Second
PM
Setting the “Hour”
Press the [+] or [-] button to set
at “AM 11”and press [E] button.
At the same time, the flashing
changes from “Hour”to
“Minute”.
FE
TIME
AM
(2) Setting the “Minute”
Pressthe [+] or [-] button to
set at “30”and press [E]
button.
TIME
AM
FE
At the same time, the
“Second”starts to run
from “00”and the LCD
screen only display “▲”
under the “TIME”mark.
TIME
FE
(3) If you want to set another
function, press the [F]
button to continue setting.
If you finished setting the
functions, replace the
cover and lock it.
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
7. SETTING THE DATE
Example: Change the Date from January 1, 2006 to June 10, 2006.
8
(1) Press the [F] button, and
position the “▲”under the
“DATE”mark. The “Year”
flashes (The flashing means
it can be changed).
F+E
DATE
Year Month Date
Setting the year
Such as example, press the [E]
button because the year 2006 is
not to be changed.At the same
time, the flashing changes from
“Year”to “Month”.
F+E
DATE
(2) Setting the “Month”
Press the [+] or [-] button to set
at “06”and press [E] button. At
the same time, the flashing
changes from “Month”to “Date”.
F+E
DATE
(3) Setting the “Date”
Press the [+] or [-] button to
set at “10”and press the
[E] button.
F+E
DATE
At the same time, the LCD
screen only display “▲”
under the “Date”mark.
F+E
DATE
(4) If you want to set another
function, press the [F]
button to continue setting.
If you finished setting the
functions, replace the
cover and lock it.
TO PLACE AN ORDER CALL: 866-487-4751
OR VISIT: WWW.TIMECLOCKEXPERTS.COM
Andere Handbücher für xl1000
1
Inhaltsverzeichnis
