Comway WG8010 Bedienungsanleitung

WG8010 cellular IP modem Quick Installation Guide

WG8010 Cellular IP Modem Quick Installation Guide

The objective of this document is to provide the user with basic information on how to

configure the modem and verify communication with COMWAY DCS.

1. WG8010 Cellular IP Modem Installation

In this example the requirements are:

• GSM/GPRS SIM with GPRS data enabled.

• An APN (Access Point Name).

• Username and Password, if GPRS is operating on a non-transparent network.

Note: If you don’t know the name of the APN you need to use, please contact your

cellular network carrier for that information.

1.1 SIM Card Installation

Insert SIM Card with the metallic part facing down and the clipped corner in the left.

Note: Not to pull out the SIM holder without pushing the eject button

1.2 Connecting the Antenna

The antenna is supplied with WG8010; connect it to the antenna connector on IP modem.

1.3 Connecting to PC

The WG8010 have one RS-232 port; connect WG8010 to PC with serial line for later

configuring.

Page 1 of 7

WG8010 cellular IP modem Quick Installation Guide

Page 2 of 7

Pin Signal Pin Signal

1 6

2 RXD 7

3 TXD 8

4 9

5 GND

1.4 Connecting the Power

Connect the 5 to 16 VDC power cord with the WG8010 IP Modem's power input. If the

power is properly supplied, the "PWR" LED will glow a solid green color to indicate that

the system is ready.

1.5 LED Indicators

The LED indicators on the front panel of the WG8010 IP Modem are described in the

following table.

LED status Device Status

DATA LED blinking Data

transmission

PWR, LINK LED blinking Not registered

PWR blinking Net search

LINK LED Permanently on Online

2. Configure WG8010 with AT command

2.1 Determine which Com Port to Use

Step 1．On older computers, there is usually a built in Com port. This is normally Com1.

Step 2．If you are using a USB-to-serial converter, you will need to determine which Com port

it is installed on.

Note: If the USB-to-serial converter has not been installed, install the necessary

drivers per the instruction supplied by your USB-to-Serial device. Then

leave the device unplugged.

Step 3．Open up the System Properties window. This is done through the Control Panel

→System or right-click on My Computer and select Properties. Select the

Hardware Tab.

Step 4．Select the Device Manager button. Expand the Ports section by selecting the + sign

WG8010 cellular IP modem Quick Installation Guide

beside

Step 5．Plug in the USB-to-Serial converter. The window should change to show the

USB-to-Serial converter installed.

Step 6．Most devices will show the Com port next to the device name. Record this number.

Note: Make sure there is no “!” or “X” next to the USB device. If you see an “!” or an

“X,” the device is not properly installed and will not work.

2.2 Start HyperTerminal

Step 1．Connect the WG8010 IP Modem to the PC COM port and run HyperTerminal

software. From the Taskbar, click [Start], followed by “All Programs” →Accessories

→Communications →“HyperTerminal”.

Step 2．You will be prompted to enter a description for the new connection. Enter a name for

the connection (e.g. “WG8010 IP Modem”) and click [OK] to continue.

Step 3．In the “Connect to” dialog box, select the PC COM port number, which is connected

to the modem, and click [OK] to continue.

Page 3 of 7

WG8010 cellular IP modem Quick Installation Guide

Step 4．In the next prompted dialog box; enter the port settings which is configured in the

modem click [OK] to continue.

Step 5．The “Connected” text in HyperTerminal status bar indicates that the PC is ready to

communicate with the modem. Perform a simple check on the connection between

Page 4 of 7

WG8010 cellular IP modem Quick Installation Guide

HyperTerminal and the modem:

Enter AT<Enter> command.

An OK response (displayed on HyperTerminal) indicates that the connection is

successfully established.

2.3 Cellular Network Connection Configuration

Step 1．Configure serial port:

AT^BAUD=115200

Step 2．Give the WG8010 a unique name:

AT^ID=”0903-1000-0032” //ID should be 15 numbers or letters

Step 3. Connect to your provider’s network

AT+CGDCONT=1,”IP”,”cmnet” // replace “cmnet” with your APN

ATDT*9

Step 4．Configure the WG8010 to talk with COMWAY Test Server

AT^SERVER=”ds.fusionunix.com”: 9000

Step 5．Setup transmission mode

AT^PKMD=1 //COMWAYProtocol

Step 6．Store the current configuration to memory:

AT^SAVE

3. Configure WG8010 with configuration software

WG8010 Configuration software can be used to configure the general parameters,

without the need to look up AT commands.

Page 5 of 7

WG8010 cellular IP modem Quick Installation Guide

Page 6 of 7

WG8010 cellular IP modem Quick Installation Guide

Page 7 of 7

Andere Handbücher für WG8010

Inhaltsverzeichnis

Andere Comway Modem Handbücher

Comway

Comway WG8010 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung