Conair CGS95A Bedienungsanleitung

Model CGS95A

Extreme Steam Upright Fabric Steamer

with Dual Heat

Instructions

for Use

For your safety

and continued

enjoyment of this

product, always

read the instruction

book carefully

before using.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are

present, basic safety instructions should always be followed,

including the following:

Polythene bags over product or package may be dangerous. To

avoid danger of suffocation, keep this wrapper away from babies

and children. This bag is not a toy.

DANGER: When the unit is used in a bathroom, unplug it after use

since the proximity of water presents a hazard even when the unit

is switched off.

WARNING: Do not use this appliance in or near bathtubs,

showers, basins, or other vessels containing water.

• Do not immerse in water or other liquids.

• Do not reach for an appliance that has fallen into water.

Unplug immediately.

• Take care to avoid contact between the hot surfaces of the unit

and the skin, paying particular attention to the face, neck and

hands.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to ensure that they do not play with

the appliance.

IMPORTANT: Always unplug the appliance when not in use or before

cleaning. Do not leave unattended when plugged in or switched on.

Do not place on any heat-sensitive surface and always allow to cool

before storing away.

• Do not use any attachments other than those supplied by Conair

Australia Pty Ltd.

• Use this appliance only for its intended use as described in this

instruction booklet.

• This appliance is not intended for commercial use.

• Never drop or insert any object into an opening or hose.

• Do not use if unit has been dropped or damaged.

• Do not use outdoors or operate where aerosol (spray) products are

being used or where oxygen is being administered.

• Keep the cord away from heated surfaces.

• Care should be taken when using the appliance due to the

emission of steam.

• Never yank the cord to disconnect from the power outlet, instead

grasp plug and pull to disconnect.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

• After use do not wrap the cord around the appliance as in time

this may cause the cord to fracture. Coil cord loosely around the

appliance in storage.

• While it is not recommended, if an extension cord is absolutely

necessary, a 15 amp rated power cord should be used. Cords rated

for less amperage may overheat. Care should be taken to arrange

the power cord so that the cord cannot be pulled or tripped over.

• Always ensure that the voltage to be used corresponds to the

voltage marked on the unit.

• For additional protection, the installation of a residual device (RCD)

with a rated operating current not exceeding 30mA is advisable in

the electrical current supplying the bathroom and other parts of

the home. Ask your installer for advice.

CAUTION:

• Unplug the appliance during filling and cleaning.

• Do not operate steamer without correctly filling the water

container.

• Do not overfill the steamer, since it can cause hot water to boil out

and burn.

• Never pour water directly into the reservoir. Put water only in

water tank.

• Only use clean cold water for filling this appliance. In hard water

areas, we recommend the use of distilled water.

• Always keep the hose and nozzle elevated above the water

container.

• Before unit is turned on, the hose must be extended, and then

place it in the hook.

• Do not place the steam nozzle directly onto any surface or on the

appliance power cord while it is hot or plugged in.

• Use with caution when changing attachments as they may contain

hot water or condensation from the nozzle. Attachments should

never be placed on the unit when in use or when preheating.

Ensure that the attachments are dry or cooled to avoid contact

with hot water.

• Attachments may get hot during use. Allow them to cool before

storing.

• When emitting steam, this appliance may cause burns if it is used

too close to the skin or eyes, or if it is used incorrectly. To reduce

the risk of contact with hot water emitting from the steam vents,

test appliance before use by holding it away from the body.

• Do not steam garments while on a person.

• Burns could occur from touching hot metal parts, hot water or

steam. Use care when you turn steam appliance upside down –

there may be hot water in the reservoir.

• Use with caution when carrying steamer, as it contains hot water.

• Hose will be hot when in use. Avoid prolonged contact to avoid

burns.

GETTING TO KNOW YOUR STEAMER

cool-touch

insulated hose

360˚ rotating,

collapsible

hanger

Clips for

steaming pants

Main On/Off

switch

(red light)

Ready to use

indicator light

(green light)

T-nozzle On/Off

button for steam

Telescoping

pole for height

adjustment

Steam nozzle with

aluminum faceplate

Removable,

easy-to-fill

large capacity

water tank

2 large

diameter

casters

UNPACKING INSTRUCTIONS

Place the box on a large, sturdy flat surface. Carefully remove the

appliance from the packing material. Keep all plastic bags away

from children.

STEAMER ASSEMBLY

Attaching the Telescopic Pole and Rotating Hanger

1. Turn the lock on top of base unit to unlock position and place

telescopic pole into opening. Turn clockwise to lock.

2. Fully extend the telescopic pole, making sure to lock the pole

upright by engaging the two clips, and hang the steam nozzle

from the cradle atop the 360 degree rotating hanger assembly.

3. Pull lower pants clips towards you and rotate clockwise to lock

into place.

4. This unit comes with a rotating hanger. To use the hanger,

simply place on top of pole firmly. Then tighten lower nut to

keep hanger upright or untighten to collapse hanger. It is now

in place to rotate 360˚. Hang your garment and steam away

wrinkles. Turn as you wish.

5. Attach the top pants clip bar to the rotating hanger by

inserting mounting pegs into the hanger’s two keyhole

openings. Push in and pull down to lock. See instruction

booklet “Using pant clip system”, Fig.3 for more details.

6. With telescopic pole now fully assembled, place the T-Nozzle

onto holder above the hanger.

7. When you are ready to steam, fill the water tank from the top

opening. Note, do not open the bottom cap as this is used for

cleaning or removing excess water only.

8. Plug the steamer unit into a standard 240V AC power outlet.

9. The bristle brush attachment easily snaps over the T-nozzle

for use. To use the creaser attachment, simply line up at base

and slide into back under T-nozzle and push firmly to attach.

See instruction booklet “Attachments” section figures 5 and 6

for more details.

TURNING STEAMER ON

1. Push the On/Off switch on base of unit to On – red

light will go on (A).

2. The unit will heat up in approximately 100 seconds

and will be ready to use when green light is on (B).

3. Push button on T-nozzle – light will go on and

steam will start. Button on T-nozzle can be used

On or as a Pause feature.

Always hold the nozzle onto the fabric while

steaming.

USING PANT CLIP SYSTEM

This fabric steamer is equipped with a pant clip system for holding

pants taut for faster and more effective steaming.

Attach the top pants clip bar to the rotating hanger

by inserting mounting pegs into the hanger’s two

keyhole openings (Fig. 3).

Push in and pull down to lock (as highlighted above).

The bottom clips can be adjusted by loosening the

knob (on the telescopic pole) and moving the pole

up and down, depending upon the length of pants.

Clip pants as shown and steam. Please note: some

pants may be too long to use the bottom clips.

If that is the case, just simply use the top clips and let

your pants hang freely.

(Fig. 1)

(Fig. 2)

(Fig. 3)

ATTACHMENTS

The bristle brush attachment easily snaps over the T-nozzle as

shown below (Fig. 5). For the creaser attachment, simply line up at

base and slide into back under T-nozzle and push firmly to attach

as shown below (Fig. 6).

Make sure your steamer is off and has cooled before adding or

removing attachments.

DUST MITES

Dust mites ﬂourish in warm, humid environments and need humidity

of more than 50% year round to survive, making most coastal areas

of Australia and New Zealand the perfect breeding ground.

Millions of dust mites exist in homes attached to ﬁbres in carpet,

bedding, pillows, sofas, rugs, throws, cushions, curtains, drapes and

children’s soft toys.

The mattress is the major breeding ground for dust mites. Depending

on its age, a mattress may contain between 100,000 and 10 million

dust mites and their eggs.

Using a steamer that emits steam hotter than 55˚C is the best and

most convenient way to eliminate dust mites from around the

home. This steamer emits steam to 130˚C.

Bristle brush attachment

(Fig. 5)

Creaser Attachment

(Fig. 6)

OPERATING INSTRUCTIONS

FILLING THE WATER TANK

(PRIOR TO PLUGGING IN THE APPLIANCE)

Remove the water tank using handle on front of tank.

Fill reservoir using opening on top of tank by holding

it under a source of cold running water until it is filled

to the desired level. Do not overfill. Position the water

tank on the base and make certain it is seated properly

in the unit.

DO NOT FILL THE TANK WITH HOT WATER.

DISTILLED OR FILTERED WATER IS BEST.

Do not unscrew the bottom cap unless for cleaning

(Fig. 4). Note, be sure always empty or fill the tank

over a sink, being careful not to spill water from the

top of the tank.

Only use clean water for ﬁlling the steamer. In hard water areas,

we recommend the use of distilled water.

There is no need to ﬁll with warm or hot water, as the steamer

heats the water while producing steam.

NB - NEVER USE ADDITIVES SUCH AS SALT, PERFUME OR DYE WITH

THIS STEAMER. THESE SUBSTANCES WILL CORRODE OR CLOG THE

INTERNAL PARTS OF THE STEAMER.

(Fig. 4)

HOW TO STEAM

This steamer is suitable for use on all types of fabric including

cotton, polyester, nylon, elastane, denim, velvet, leather, wool,

cashmere, silk and delicate non-iron fabrics, as well as fabrics with

beading and embellishments.

This steamer is also great for all dry-clean only items – helping you

to save time and money on expensive dry cleaner bills.

It is also great for use on all home fabrics and soft furnishings such

as curtains, rugs, cushions, sofas, bedding, mattresses, pillows and

linen to help remove odours, kill dust mites and rejuvenate fabric.

Depending on the type of garment/fabric to be steamed, there are

several ways of steaming:

1. Grasp the nozzle with the steam jets facing away from you.

2. Begin at the bottom of the garment to allow the steam to rise

and remove wrinkles from the inside and outside of the fabric.

NB – Some garments are best steamed on the underside of the

material.

3. Slowly move the nozzle from the bottom to the top of the

garment.

4. Remove the nozzle from the garment and smooth the fabric

with your free hand. This will allow the fibres of the fabric to

relax and help eliminate wrinkles and creases.

NOTE: Test fabric for colour fastness in a small inconspicuous spot.

Drape linens, towels, handkerchiefs and napkins over a rod or place

on a towel rack when steaming. Heavier garments and fabrics may

require repeated steaming. Repeat steaming as necessary. It takes

some practice to gain speed and efficiency and to learn that some

fabrics require multiple steam applications.

**Do not directly touch velvet, silk or delicate fabrics with the

nozzle.

Inhaltsverzeichnis

Andere Conair Küchengerät Handbücher

Conair

Conair GS15RN Bedienungsanleitung

Conair

Conair FSX10PS Series Bedienungsanleitung

Conair

Conair Extreme Steam CGS65A Bedienungsanleitung

Conair

Conair ExtremeSteam GS75C Bedienungsanleitung

Conair

Conair GS23 Bedienungsanleitung

Conair

Conair GS1 Bedienungsanleitung

Conair

Conair GS11RH Bedienungsanleitung

Conair

Conair GS15RN Bedienungsanleitung

Conair

Conair GS38C Bedienungsanleitung

Conair

Conair Ultimate GS28 Bedienungsanleitung

Conair

Conair GS59 Bedienungsanleitung

Conair

Conair GS11DR Bedienungsanleitung

Conair

Conair Ultimate GS7 Bedienungsanleitung

Conair

Conair Easy Care 5000 Bedienungsanleitung

Conair

Conair GS23 Bedienungsanleitung

Conair

Conair CGS4A Bedienungsanleitung

Conair

Conair Extreme Steam Bedienungsanleitung

Conair

Conair CGS19A Bedienungsanleitung

Conair

Conair GS15RC Bedienungsanleitung

Conair

Conair GS29 Bedienungsanleitung

Conair

Conair GS38C Bedienungsanleitung

Conair

Conair GS23 Bedienungsanleitung

Conair

Conair GS51 Bedienungsanleitung

Conair

Conair Extreme STEAM GS23C Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung