Conair ConairPhone CID110 Bedienungsanleitung

*You must subscribe to Caller ID service from your local

telephone company to receive Caller Identification.

HOTLINE 1-800-366-0937

CID110 Owner’s Manual

Caller ID* Telephone

with 10-Memory Dialing

NLM055Y2 Printed in China

Service Center

7475 N. Glen Harbor Blvd., Glendale, AZ 85307

IB-4577B

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of fire, electric shock

and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath

tub, wash bowl, kitchen sink or laundry tub, in a wet basement

or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during

an electrical storm. There may be a remote risk of electric

shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity

of the leak.

4. Use only the power cord and batteries indicated in this manual.

Do not dispose of batteries in a fire.They may explode.Check

with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

123

LOCATION OF CONTROLS

1. Receiver

2. Receiver Volume Control

3. Hook Switch

4. Keypad

5. Tone/Pulse Switch

6. Redial Button

7. Transmitter / Mic

8. Store Button

9. Memory Button

10. New Call LED

11. Ringer Hi/Lo/Off Switch

12. LCD Display

13. Battery Compartment

14. Review / Button

15. Erase Button

16. Call Back Button

CONGRATULATIONS!

You have purchased a CID110, Caller ID Telephone with 10-

Memory Dialing manufactured to the highest standards of

ConairphoneTM. Before installing and operating, be sure to read

this manual.

GENERAL INFORMATION

UNPACKING

This package contains:

• CID110 Caller ID Telephone with 10-Memory Dialing

• Owner’s Manual

• Fully Modular Coil Cord

• Fully Modular Telephone Line Cord (Long Straight Cord)

• Fully Modular Telephone Line Cord (Short Straight Cord)

• Quick Installation Guide

• Important Notice

• Two (2) Memory Index Labels

• Warranty Card

If anything is missing or damaged, contact the place of purchase.

Keep the packaging to transport telephone.

For your reference, keep a record of the date purchased.

Please save the sales receipt for the warranty reference.

Date of Purchase ___________________________

INSTALLATION INSTRUCTIONS

Follow these precautions:

a. Never install telephone wiring during a lightning storm.

b. Never install telephone jacks in wet locations unless the jack

is specifically designed for wet locations.

c. Never touch uninsulated telephone wires or terminals unless

the incoming telephone line has been disconnected at the

network interface.

d. Use caution when installing or modifying telephone lines.

TO INSTALL BATTERIES

Batteries are required for the Caller ID functions and Telephone

operations of the unit.

1. Open the battery door by pulling back the latch.

2. Insert three (3) AA alkaline batteries (not included).

3. Snap the battery door back into place.

Note: Once batteries are installed, you have 20 seconds to setup

the Caller ID.

SETTING UP YOUR CID110

DO NOT CONNECT the line cord to the wall outlet until the

Caller ID setup has been completed.

NOTES:

• If the Caller ID is not setup within 20 seconds after battery

installation, press and hold both the [ ] and [ ] keys for 4

seconds to activate the Caller ID setup.

• If you do not have the Caller ID service and want the time/

date set, please go to Caller ID setup section and ‘ENTER

TIME DATE’ setting.

The LCD shows ‘ENTER LANGUAGE’

followed by a choice of 3 languages

(English, Spanish, French).

The LCD then shows ‘ENG ESP FRA’.

NOTE: The ‘ENG’ is BLINKING. Press

[] or [ ] to select‘ENG’, ‘ESP’, or ‘FRA’.

Press [ERASE] to confirm.

If ENG is selected, the LCD shows ‘LCD

CONTRAST’.

Press [ ] or [ ] to adjust five levels (from

1 to 5, default is 3) contrast of LCD.

Press [ERASE] to confirm.

If contrast is set, the LCD shows

‘ENTER AREA CODE’. The first digit

‘–’ of the area code will blink.

Press [ ] or [ ] to enter the area code.

Press [ERASE] to confirm and go to next entry.

Repeat above steps until 3-digit area code is set.

456

If area code is set, the LCD shows

‘ENTER TIME DATE’.

Press [ ] or [ ] to select the hour digits.

Press [ERASE] to confirm and go to the next entry.

Press [ ] or [ ] to select the minute

digits.

Press [ERASE] to confirm and go to the

next entry.

Press [ ] or [ ] to select the month digits.

Press [ERASE] to confirm and go to the

next entry.

Press [ ] or [ ] to select the date digits.

Press [ERASE] to confirm.

The LCD shows ‘TOTAL:00 NEW:00’,

which means both the total call and new

call counter are zero.

USING THE PHONE ON A DESK

1. Plug the long telephone line cord into the jack in the bottom

of the BASE, thread it through the groove toward the back of

the unit, then plug it into the modular phone jack.

2. Connect the COIL CORD to the jack in the HANDSET and

the BASE.

HANGING THE PHONE ON THE WALL

When the CID110 is wall mounted, the HANDSET GUIDE holds

the handset in place in the cradle.

On a wall phone plate

1. Plug the short telephone line cord into the jack in the base

bottom and into the jack on the plate.

2. Hang the base on to the two pins and pull the base down to

lock it on.

3. Plug the coil cord into the handset and base jacks.

On a wall without a plate

1. Install 2 screws with anchors into the wall, one above the

other, 3-1/4" apart, extending 3/16" out from the wall to hold

the base securely.

2. Install the long telephone line cord into the jack in the base,

thread it through the groove and plug it into modular wall

jack.

3. Hang the base on the screws and pull it down to lock it on.

4. Plug the coil cord into the handset and base jacks.

TELEPHONE FEATURES

Tone/Pulse Switch

Set switch to your type of service. If you don’t know whether you

have tone or pulse:

1. Put the switch on “Tone”.

2. When you have a dial tone, press any key on the keypad. If

the dial tone stops, leave it on “Tone”. If not, change the setting

to “Pulse”.

Receiver Volume Control

The receiver volume control is located on the side of the handset

of your phone. This enables you to adjust the receiver volume

from NORM to HI for a better listening level.

Ringer Off/Low/High

Your CID110 features a harmonic dual tone ringer that can be

adjusted from a loud (HI) to a soft (LO) sound level. When you

don’t want to be disturbed, slide the switch to the OFF position.

You can still make outgoing calls without being disturbed by

incoming calls.

Pause

Whether you have Tone or Pulse service, you can insert a 4-

second PAUSE into the dialing or storing of a number into

memory in order to access custom and telebanking services,

long distance, etc. Press [Redial] at the desired point in the

number. Press [Redial] again if an additional 4 seconds is

needed.

Redial Button

Automatically redials last number called (up to 32 digits). If the

number was busy or unanswered:

1. Lift the HANDSET.

2. Press [Redial].

TELEPHONE OPERATION

Receiving a Call

1. When your phone rings, pick up the handset and use it like

any basic telephone.

2. Hang up the handset to release the telephone line when your

conversation is completed.

Dialing a Call

1. Pick up the phone and wait for a dial tone.

2. Press the keypad for the telephone number you wish to dial.

Tone/Pulse Combination Dialing

Combination dialing is useful to subscribers of Pulse (rotary)

service who wish to gain access to various low-cost long-

distance or automated computer services otherwise not available

to them.

1. With the Tone/Pulse switch in the Pulse position, dial the

phone number.

2. Press [*], and your telephone will change to Tone dialing

mode.

3. Dial your code/authorization number. When your call is

completed, your telephone will automatically return to the

PULSE dialing mode.

NOTE: Combination dialing can also be stored into the memory

for one-touch access to your long distance or automated

computer service.

789

BASIC MEMORY PROGRAMMING

The CID110 comes with 10-memory dialing.

NOTE: Your local phone company restricts the time you can

have the handset off the base (off-hook).

YOU SHOULD PROGRAMTHE CID110 MEMORYWITHTHE

LINE CORD UNPLUGGED FROM THE WALL, IF YOU ARE

GOINGTO PROGRAM MORETHAN ONE PHONE NUMBER.

Pick up the handset, and press [Store] to enter memory store.

Press the keypad to enter the number that you want to program.

The LCD on the back of the handset confirms the numbers you

entered.

Press [Store].The ‘MEM’will be displayed on the right corner of

LCD.

Press the memory location (0 to 9) on the keypad.The LCD will

then return to the ‘Answer-Ready’ mode, and display the total

call counter, new call counter, current time and date.

Copy from the Caller ID to Telephone Memory

Press [ ] or [ ] until the Caller ID memory location to be copied

appears on the LCD. Press [Store] twice to enter memory store.

The ‘MEM’ will be displayed on the right corner.

Press the memory location (0 to 9) on the keypad.The LCD will

then return to the ‘Answer-Ready’ mode, and display the total

call counter, new call counter, current time and date.

If no key is pressed within 20 seconds, the LCD will return to

‘Answer-Ready’mode.

Repeat the above steps to store a different number in the same

speed dial location, or to store a new number in a different speed

dial location.

NOTES:

• Pressing [Redial] will place a 4-second PAUSE into the

number.Which may be required for accessing special phone

services.

• You can store a number with up to 16 digits maximum. Only

the last 14 digits will be displayed.

MEMORY DIALING

Pick up the handset to make your call.

Press [MEM] [0] ... [MEM] [9] for one of the 10 memory locations

to be dialed.

NOTE: Remember to plug the telephone line cord back into the

wall.

CALLER ID OPERATION

NOTE: Batteries must be installed, or Caller ID operations will

not work properly (see “To Install Batteries”).

If an incorrect, invalid or incomplete

Caller ID signal is received, the LCD

shows ‘-LINE ERROR-’.

If only the caller’s phone number is

received, the LCD shows the caller’s

phone number with the time and date it

was received.The ‘NEW’ icon turns on and New Call LED blinks.

If both the caller’s name and phone

number are received, the LCD shows the

caller’s name and phone number with

the time and date it was received. The ‘NEW’ icon turns on and

New Call LED blinks.

If the name and number are not available

due to the caller’s restriction, the LCD

shows ‘-PRIVATE CALL-’ with the time

and date received. The ‘NEW’ icon turns on and New Call LED

blinks.

If the name and number are not

available, the LCD will show

‘-UNAVAILABLE-’with the call’s time and

date. The ‘NEW’ icon turns on and New Call LED blinks.

If no key is pressed within 20 seconds,

the LCD will show the ‘Answer-Ready’

mode, and display the total call counter,

new call counter, current time and date.

VIEW THE CALLER ID MEMORY

If you have new calls (‘NEW’ icon and New Call LED is lit).Press

[] or [ ] to read all of the most recent calls. The CALL# will

decrease.

Once all the new calls have been read, ‘END OF NEW CALL’

will be displayed.

Press [ ] to view the oldest calls, or press [ ] to view the most

recent calls.

NOTE: After you view all the call in memory, the LCD will show

‘END OF LIST’.

NOTES:

1. The New Call LED will blink until all the new Caller ID data

has been reviewed.

2. If the ‘RPT’ icon is turned on, you have received multiple NEW

calls from the same number.

3. If you receive a call from a number stored in (previously

reviewed) memory, the data in memory will be replaced with

the new call’s time and date and the ‘NEW’ icon will be turned

on.

If no key is pressed within 20 seconds, the LCD will show the

‘Answer-Ready’ mode, and display the total call counter, new

call counter, current time and date.

10 11 12

ERASE THE CALLER ID MEMORY

Press [ ] or [ ] for the Caller ID memory location to be reviewed.

To clear a single Caller ID memory location, press [ERASE]

twice quickly.

The data for that call will be erased, and the CALL# and Caller

ID information will be updated.

After all new message being reviewed, press and hold [ERASE]

for 3 seconds. The message ‘ERASE ALL CALLS?’ will appear

to confirm your action. Press [ERASE] to clear all the information,

then the message ‘NO CALLS’ appear.

Both the total call and new call counters will become zero, and

the current time and date will be displayed.

NOTE: All new calls must be reviewed before clearing the entire

memory.

CALL BACK (REDIAL) FROM THE

CALLER ID MEMORY

With the handset hung up on the base press [ ] or [ ] to find the

Caller ID memory location to be redialed.

Press [CALL BACK] twice to redial, the LCD shows ‘LIFT

HANDSET’ or ‘PICK UP CALL’.

Pick up the handset to make your phone call.

With the handset off hook, press [ ] or [ ] to find the Caller ID

memory location to be redialed. Press [CALL BACK] twice, the

number will then be dialed automatically.

WHEN THE CALLER’S PHONE

NUMBER HAS A DIFFERENT AREA

CODE FROM THE PRESET:

The long distance dialing digit ‘1’ will be inserted automatically

during Caller ID memory call back.

Press [CALL BACK], 11 digits number will blink. Press [CALL

BACK] again to confirm to dial the 11 digits number.

WHEN THE CALLER’S PHONE

NUMBER HAS THE SAME AREA CODE

AS THE PRESET:

The long distance dialing digit ‘1’ and the 3 digits area code will

be deleted automatically during Caller ID memory call back.

Press [CALL BACK], 7 digits number will blink. Press [CALL

BACK] again to confirm to dial the 7 digits number.

NOTE: Your telephone company may require a different format

for making out-of-area (toll) calls WITHIN your area code. See

the next section for the procedure to obtain the applicable toll-

call format for your phone company.

WHEN YOUR TELEPHONE COMPANY REQUIRES YOU TO

DIAL OTHER THAN A 7-DIGIT NUMBER (SAME AREA

CODE) OR 11-DIGIT NUMBER (DIFFERENT AREA CODE)

TO MAKE TOLL CALLS WITHIN YOUR AREA CODE,

FOLLOW ONE OF THE 4 OPTIONS BELOW FOR CALLER

ID CALL BACK.

Option 1

1+Area Code+7-Digit Number (11 digits)

Option 2

1+7-Digit Number (8 digits)

Option 3

Area Code+7-Digit Number (10 digits)

Option 4

7-Digit Number Only.

Follow the procedure below to select one of the above

options for Caller ID call back.

With the handset hung up on the base.

1 Press [ ] or [ ] to find the Caller ID memory location to redial.

Press [CALL BACK], the 7-digit number (if same area code)

or 11-digit number (if different area code) will blink.

2. Press [ ] or [ ] to select one of the options.

3. Press [CALL BACK] again to confirm the dial.

LOW BATTERY INDICATION

The CID110 will signal you when the batteries become weak

and need replacement. Once battery power has been sufficiently

drained, the CID110 will appear the BATTERY LOW icon ( )on

the LCD display. Replace the AA batteries with three (3) fresh

ones in order to maintain the Caller ID and Speed Dialing

memories. If you do not install fresh batteries within 2 minutes,

your Caller ID and telephone memory information may be lost.

CUSTOMER INFORMATION

This equipment complies with Part 68 of the FCC rules and the

requirements adopted by the ACTA. On the bottom

of this

equipment is a label that contains, among other information, a

product identifier of US: DJTMT10BCID110

If requested, this

number must be provided to the telephone company.

The applicable jacks ( i.e. RJ11C ) for this equipment are provided

in the packaging with each piece of approved equipment. The

jacks are certified by Universal Service Order Codes (USOC).

A plug and jack used to connect this equipment to the premises

wiring and telephone network must comply with the applicable

FCC Part 68 rules and requirements adopted by the ACTA. A

compliant telephone cord and modular plug are provided with

this product.They are designed to be connected to a compatible

modular jack that is also compliant.See installation instructions

for details.

The REN is used to determine the number of devices that may

be connected to a telephone line. Excessive RENs on a

telephone line may result in the devices not ringing in response

to an incoming call. In most but not all areas, the sum of RENs

should not exceed five (5.0). To be certain of the number of

devices that may be connected to a line, as determined by the

total RENs, contact the local telephone company.

13 14

If this equipment CID110

causes harm to the telephone network,

the telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance notice

isn’t practical, the telephone company will notify the customer

as soon as possible.Also, you will be advised of your right to file

a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities,

equipment, operations or procedures that could affect the

operation of the equipment. If this happens the telephone

company will provide advance notice in order for you to make

necessary modifications to maintain uninterrupted service.

If you experience trouble with this equipment, disconnect it from

the network until the problem has been corrected or until you

are sure that the equipment is not malfunctioning.

Please follow instructions for repairing if any (e.g. battery

replacement section); otherwise do not alter or repair any parts

of device except specified.

Connection to party line service is subject to state tariffs. Contact

the state public utility commission, public service commission

or corporation commission for information.

This equipment is hearing aid compatible.

NOTICE: If your home has specially wired alarm equipment

connected to the telephone line, ensure the installation of this

(equipment ID if any) does not disable your alarm equipment. If

you have questions about what will disable alarm equipment,

consult your telephone company or a qualified installer.

WARNING: Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules.These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. Some cordless telephones operate at frequencies

that may cause interference to nearby TV’s and VCR’s; to

minimize or prevent such interference, the base of the cordless

telephone should not be placed near or on top of a TV or VCR;

and, if interference is experienced, moving the cordless

telephone farther away from the TV or VCR will often reduce or

eliminate the interference. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

ADDITIONAL INFORMATION

A. When your CONAIRPHONETM is not in use make sure the

handset is engaged into the base unit.

B. Avoid rough handling, areas with excessive moisture heavy

dust or extreme temperature.

C. To clean, use mild detergent and slightly damp cloth, never

use strong solvents or abrasives.

D. Connecting this telephone to a coin operated telephone or a

party line is prohibited by law.

E. If it is determined that your telephone is malfunctioning, the

FCC requires that it be disconnected from the modular outlet

until the problem has been corrected.

SERVICE

According to FCC regulations, this equipment, which has been

certified and registered by the FCC, may only be repaired by

authorized persons. If repairs or adjustments are made by an

unauthorized person, the FCC certification may be voided.

Should you encounter any problems, please call the

ConairphoneTM toll-free Customer Hotline for assistance:

1-800-366-0937, Monday - Friday

between the hours of 8:30 am - 9:00 pm and

Saturday 8:30 am - 12:30 pm (EST).

You can also visit our website at

www.conairphone.com

FOR IN-WARRANTY SERVICE:

Package your complete unit (including all adapters, line cords,

and other accessories) and ship the unit postage prepaid* and

insured (for your protection) to:

CONAIRPHONETM

DEPT.: In Warranty Repair

7475 North Glen Harbor Blvd., Glendale, AZ 85307

Be sure to include your return address, proof of purchase, a

daytime phone number, $5.00 for postage and handling*, and a

brief explanation of your difficulties.

*NOTE: California residents need only provide proof of purchase

and should call 1-800-366-0937 for shipping instructions.

FOR OUT-OF-WARRANTY SERVICE:

You may call our toll-free Help Line for the price of a replacement

before returning your unit. Please follow all instructions for In-

Warranty service (above) to return your unit, and mark the

package: DEPT.: Out-of-Warranty.

If you have called and know the cost of your replacement, please

include this information with your unit for prompt service.

QUESTIONS?

STOP ... don’t take unit back to the store.

LOOK ... for the toll-free “help”telephone number.

LISTEN ... as our experts talk you through the problem.

For immediate answers to your questions regarding operation,

missing parts or installation, call:

CONAIRPHONETM

HOTLINE AT:

1-800-366-0937

LIMITED WARRANTY

This ConairphoneTM is warranted to the original purchaser to be

free from defects in materials and workmanship under normal

installation, use, and service for a period of one (1) year from

the date of purchase as shown on the purchaser’s receipt.

The obligation of ConairphoneTM Retail Sales under this warranty

shall be limited to repair or replacement (at our option) during

the warranty period of any part which proves defective in material

or workmanship under normal installation, use, and service,

provided the product is returned to ConairphoneTM or to one of

our authorized Service Centres TRANSPORTATION CHARGES

PREPAID. Products returned to us or to an Authorized Service

Center must be accompanied by a copy of the purchase receipt.

In the absence of such purchase receipt, the warranty period

shall be one (1) year from the date of manufacture. To obtain

service under this warranty, return the defective product to the

service center nearest you together with your sales slip and

$5.00 for postage and handling.(California residents need only

provide proof of purchase).You may also have other warranty

rights which vary from state to state.

This warranty shall be invalid if the product is damaged as a

result of defacement, misuse, abuse, neglect, accident,

destruction or alteration of the serial number, improper electrical

voltages or currents, repair alteration or maintenance by any

person or party other than our own service facility or an

authorized Service Center, or any use violative of instructions

furnished by us.

16 17 18

This warranty is also rendered invalid if this product is removed

from the country in which it was purchased, if it is used in a

country in which it is not registered for use, and/or if it is used in

a country for which it was not designed. Due to variations in

telephone systems and communications laws, this product may

be illegal for use in some countries. ConairphoneTM assumes

no responsibility for damages or penalties incurred resulting from

the use of this product in a manner or location other than that

for which it is intended.

This one-year limited warranty is in lieu of all other expressed

warranties, obligations, or liabilities.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR

LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE ONE-YEAR DURATION OF THIS

WRITTEN LIMITED WARRANTY. SOME STATES DO NOT

ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

BREACH OF THIS OR ANY OTHER WARRANTY,

EXPRESSED OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or limitation of special,

incidental or consequential damages, so the above limitation or

exclusion may not apply to you.This warranty gives you specific

legal rights, and you may also have other rights which may vary

from state to state.

Inhaltsverzeichnis

Andere Conair Telefon Handbücher

Conair

Conair GH3065 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung