Confer Plastics CCX-IG Einrichtungshandbuch

SAVETHESE INSTRUCTIONS

DEALER/INSTALLER: GIVE TO HOMEOWNER

CONFER IN-GROUND

CURVE STEP / IN-GROUND

CURVE STEP SYSTEM

ASSEMBLY AND INSTALLATION MANUAL

Made in the U.S.A. by

www.conferladders.com

Model CCX-IG

Note: 40 lbs. of sand required!

Model CCX-IG System

Note: 70 lbs. of sand required!

SAND

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 1

Stand up both side

panels [A]. Insert

panel brace [B] into

opening located on

[A] then push down

to lock in place.

Step 1

With the thin edge of

the curved riser [C]

facing downward

align the lower tabs

with the openings on

part [A] and push in.

Note risers must be

curved inward.

Step 2

While holding lower

tabs in part [A] align

the top tabs then tap

down with a rubber

mallet until flush.

Step 3

Install the rest of

the curved risers

[C] by flexing the

side panels [A]

outward enough to

insert part [C] tabs

into part [A]. Tap

into place with

rubber mallet.

Step 4

Confer Plastics “CURVE” In-Ground Pool Step must be assembled with the treads and risers curved inward

The CURVE Step requires 40 lbs. of sand to complete assembly. The Curve Step with optional add-on requires a

total of 70 lbs. of sand. Choose a location close to the swimming pool for assembly.

Hardware Pack

2 - Plugs [WG]

8 - #10 x 1-1/4" screws

2 - Labels-No Jumping/Diving

Hardware not provided to

fasten step to concrete.

Purchase locally.

Needed for Assembly

- Rubber mallet

- Funnel

- Cordless Drill

- Phillips screwdriver

- Liquid soap or lubricant

- Sand - 40 lbs. for (Curve Step)

- 70 lbs. for (Curve System)

Model# CCX-IG - CURVE IN-GROUND POOL STEP

ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY

Parts List

2 - Side panels [part A]

1 - Panel brace [part B]

3 - Curved risers [part C]

4 - Handrail posts [part E]

2 - Deck connectors [part F]

2 - Handrails [part G]

4 - Foot pads [part H]

2 - Treads [part I]

1 - Top tread [part I-3]

If missing parts call - Toll free U.S. - 800-635-3213 or www.Conferplastics.com

I-3

prpd.Confer-CurveStepIGr17_Confer-Step-1_R1 6/21/13 8:40 PM Page 2

IFYOU HAVE THE CONFER CURVE STEP WITHOUT THE ADD-ON CONTINUE WITH STEP 10.

IFYOU HAVE THE CONFER CURVE STEP WITH OPTIONAL ADD-ON SKIP STEPS 10-18 AND CONTINUE

WITH STEP 19.

Tilt the step

backwards to

expose all four

of the rounded

tabs on the bot-

tom edges.

Step 5

Rotate

90°

Install the first tread

[I] by placing over

the tabs on the side

panels as shown.

While holding part

[I] down on the side

panels tap inward

with a rubber

mallet until locked

in place.

Step 10

Each side panel [A]

requires 20 lbs of sand

split between the two fill holes.

Sand is needed as ballast

to hold step down in the water.

Using a funnel fill the lower hole

completely to the top with sand.

Shake the panel to help settle the

sand, lower hole must be

completely filled. Pour whatʼs left

from the 20 lbs into the upper

fill hole. Using provided cap,

plug the lower fill hole only.

Upper fill hole must remain open.

Repeat procedure to fill the

second part [A].

Step 9

Step 7

Determine which

side will be

facing up on the

front foot pads

[H], # 1 for a

flat bottom pool

or # 2 for a pool

with slight taper

towards the

center, install

both parts [H].

The two back foot

pads [H] will always

be installed with #1

facing up. Place part

[H] over the rounded

tab, strike with a

rubber mallet until

seated onto the

rounded tab. Repeat

to install second

part [H].

Step 8

SAND

Pour

sand into

funnel.

Pour

sand into

funnel.

Repeat step 10 to install

second tread [I].

Step 11

To install the lower

handrail posts [E] first

locate the openings

on part [A] just below

the second tread

marked with #3. Next

insert the tabs on part

[E] all the way into the

openings then tap

down with a rubber

mallet until seated.

Repeat to install the

other part [E].

Step 12

STOP!

Installing the

Foot Pads [H]:

If swimming

pool has a flat

bottom, all four

foot pads [H] will be installed with the #1 facing up.

If swimming pool has a slight taper towards the

center, the back foot pads will be installed with #1

facing up and the front foot pads with #2 facing up.

Step 6

#1 #2

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 3

To install the upper

handrail posts [E] first

locate the openings on

panel [A] marked with

#3. Next insert the tabs

on part [E] all the way

into the openings then

tap down with a rubber

mallet until seated.

Repeat to install the

other part [E].

Step 13

Place one of the deck

connectors [F] over

the upper handrail

post and slide down.

Check to make sure

side marked [This

Side down] is

facing downward.

Repeat to install the

second part [F]

Step 15

Place handrails [G]

over the top of handrail

posts, push down to

lock in place.

Step 16

With the step in place and positioned

about 1 inch away from inside of pool wall

[back of step must not touch pool liner] extend the two

deck connectors onto the pool deck and attach to the

handrail posts using 2- #10 x 1-1/4” screws through the deck

connectors and into the posts. If you have a wood deck attach

the deck connectors to the pool deck using 2-#10 x 1-1/4

screws in each connector. If your pool deck is concrete consult

with your local hardware store for the proper anchors and screws.

With a helper place the pool step into

swimming pool. Hold the step under

water at a slight angle until all the air bubbles stop. Tilt the

step in the other direction until all the air bubbles stop. Be

patient this process will take a few minutes.

If the pool step is still floating all of the air is not out.

Lean step to the side again until air bubbles stop.

The top tread [I-3] will

install slightly different

than the previous two.

Install this tread by

placing over the four

tabs located on side

panels [A]. Using a

rubber mallet strike

the top of the tread

directly over the tabs

until seated.

Step 14

Step 18Step 17

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 4

Install the add-on panel

[J] by inserting the three

tabs into the three

openings located

towards the back

of step panel [A].

Push the tabs all

the way in,

then tap panel

down with a

rubber mallet

until seated

in openings.

Step 19

Next, install one of the foot pads [H]

onto the tab located on the bottom of

the large flex riser [M] by placing over

the raised tab and striking with a rubber

mallet until seated. Foot pad [H]

should be installed in the same

direction as the

front foot pads

on base step.

[Refer to steps

7 & 8].

Step 20

Tilt the step back far

enough to slide the

end of large flex riser

[M] up into the slot

located on the front

bottom edge of the

add-on side panel.

Step 21

Insert the

tab on the

other end of

the flex riser

[M] into the

opening on

side panel

[A].

Step 22

Attach the last foot

pad [H] on to the

bottom of the tread

support [N] by placing

over the raised tab

and striking with a

rubber mallet until

seated. Foot pad [H]

should be installed

in the same position

as the front foot

pads on base step.

Step 23

Locate the notch

on the bottom

edge of the large

flex riser [M].

Slide the step

support [N] under

then rotate up

making sure part

is in notch.

Step 24

Additional Parts for Step Add-On

2 - Foot pads [Part H]

1 - Add-on panel [Part J]

1 - Short handrail post [Part K]

1 - Long handrail post [Part L]

1 - Large flex riser [Part M]

1 - Tread support [Part N]

1 - Large curved tread [Part O]

1 - Medium flex riser [Part P]

1 - Medium curved tread [Part Q]

1 - Small flex riser [Part R]

1 - Small curved tread [Part S]

1 - Plug [WG] (installed in add-on panel)

CONFER CURVE STEP

ADD-ON INSTRUCTIONS

The curve add-on can only be installed on the right side of the step as you

are facing it.The add-on requires an additional 30 lbs. of sand.

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 5

Position the other end of the tread over

side panel [A]. Move the large flex riser [M]

in or out until it slips up into the groove

located on the bottom of

the large curved tread [O].

It will also be necessary

to align the tabs on the

tread support [N] with

the two openings on

the bottom of the large

curved tread.

Once everything

is in position tap

down on the large

tread to lock onto

panel [A].

Step 28

Install the first tread [I] onto the base

step by placing over the tabs on the side

panels [A] as shown.

While holding the

tread down, tap

inward with a

rubber mallet until

locked in place.

Step 29

Install the short

handrail post [K]

into the lower

opening on the

add-on panel [J]

marked with #3

next to it. Push

the tab on the

post all the way

in; then tap down

to lock in place.

Step 30

Place the medium curved tread [Q] over

the short handrail post and down on to

the tabs located on the add-on panel [J].

Move the riser in or

out until it slips up

into the groove on

the bottom of the

tread, using a

rubber mallet strike

the top of the tread

until locked

onto tabs.

Step 32

CONFER CURVE STEP ADD-ON INSTRUCTIONS (Cont’d.)

At this time add 30 lbs of sand through the

two fill holes located on the add-on panel.

Using a funnel fill the lower hole com-

pletely to the top with sand. Shake the panel

to help settle

the sand. Lower

hole must be

completely filled.

Pour whatʼs left

from the 30 lbs,

into the upper hole.

Using provided cap,

plug the lower fill

hole only. Upper fill

hole must remain open.

Step 25 The next step will require an extra set of hands to help

align the large flex riser [M] and the tread support [N] into

the groove and the openings located on the bottom side of

the large curved tread [O].

Step 26

Fill

Holes

It will be easier to start from

the add-on panel side and

work towards the base step.

Start by placing the large

curved tread in approximate

position over the panels and

flex riser. Next align the tabs

on the add-on panel with the

openings on the bottom side

of large curved tread. Lock

the tread down by striking

top of tread directly over the

tabs with rubber mallet.

Step 27

Next, install the medium flex riser [P]

by sliding down into the slot located on

the add-on panel [J].

Insert the tab located

on the end of flex

riser into the opening

on side panel [A].

Riser will rest on

the top back of

tread below.

Step 31

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 6

CONFER CURVE STEP ADD-ON INSTRUCTIONS (Cont’d.)

Install the second tread

[I] onto the base step

Step 33 Install the long handrail

post [L] into the opening

on the add-on panel [J]

marked with #3 next to it. Push the tab all

the way in then tap down to lock in place.

Step 34 Install the small flex

riser [R]

Step 35

Place the small

curved tread [S] over

the handrail post and

attach the same as in step 32.

Step 36 Install the lower and

upper handrail posts [E]

to the left side panel by

repeating steps 12 and 13.

Step 37 Repeat step 14 to

install the top tread

[1-3].

Step 38

Place both deck con-

nectors [F] over the

upper handrail posts and slide down.

Check to make sure the side marked [this

side down] is facing downward.

Step 39 Place handrails [G] over

the top of handrail posts

and push down to lock

in place.

Step 40

TO PLACE STEP IN POOL FOLLOW STEPS 17 AND 18.

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 7

CP-CURVE STEP-IG 01-13

Safety Information

1) Always follow the manufacturerʼs

recommendations for the safe use of all hand

tools and equipment.

2). Do not use the Confer Curve Step for any

purpose other than that for which it is intended.

3). When lifting awkward or heavy loads, have

another person help you.

4). Maximum weight on steps not to exceed 400 lbs.

5). WARNING: Exceeding the recommended weight

restriction may cause the unit to fail.

6). Consult your local building department before

installation of your pool and equipment.

TO WINTERIZEYOUR POOL

We suggest removing your Confer Curve Step from the pool

for the off-season months.

If your Confer Curve Step is attached to a deck: Two people

are required for this operation and it is best to remove the

unit while the water is still warm enough so that one person

can get into the pool. Disconnect the mounting brackets

from the deck. The person in the water can lift the unit up

while the person on the deck helps to pull and guide the unit

onto the deck. After the unit is on the deck, and the water

has drained out of the steps, lay the unit on itʼs back side so

that most of the water drains from the side panels.

If getting into the water is not an option the unit can be

removed by both people standing on the deck and lifting and

tilting the unit to drain some of the water from the steps. After

the unit is light enough carefully lift it from the pool.

CAUTION: POOL STEP WILL BE HEAVY, PLEASE HAVE

ADDITIONAL HELP WHEN REMOVING FROM

SWIMMING POOL. DO NOT ATTEMPT TO REMOVE

STEP BYYOURSELF.

The Confer Curve Step can be covered, if desired, and

stored outdoors.

Printed in U.S.A.

MADE IN THE U.S.A. by:

CONFER PLASTICS, INC. FIVE YEAR WARRANTY

Confer Plastics, Inc. warrants their swimming pool ladders and steps to be free from defects in

workmanship for five years from date of purchase.

DO NOT RETURN DEFECTIVE PART TO DEALER

E-MAIL CONFER PLASTICS AT: [email protected]

A PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM,

PROOF OF PURCHASE AND YOUR CONTACT INFORMATION.

INFORMATION MAY ALSO BE FAXED TO CONFER PLASTICS AT: 716-694-3102

OR MAILED TO THE ADDRESS BELOW. UPON REVIEW OF THE INFORMATION YOU

WILL BE NOTIFIED IF PART IS COVERED UNDER THE WARRANTY AND

THE SHIPPING/HANDLING CHARGES.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Confer Plastics, Inc.

97 Witmer Road

North Tonawanda, N.Y. 14120-2421

97 Witmer Road

North Tonawanda, New York 14120-2421

Toll Free U.S. 800-635-3213

FAX 716-694-3102

www.conferladders.com

prpd.Confer-CurveStepIGr16:Confer-Step-1_R1 1/3/13 2:26 PM Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Confer Plastics Leiter Handbücher

Confer Plastics

Confer Plastics PES-1X Bedienungsanleitung

Confer Plastics

Confer Plastics PES-G Einrichtungshandbuch

Confer Plastics

Confer Plastics 6000 Einrichtungshandbuch

Confer Plastics

Confer Plastics 7000X Bedienungsanleitung

Confer Plastics

Confer Plastics 6000 Bedienungsanleitung

Confer Plastics

Confer Plastics EVOLUTION 7100 Einrichtungshandbuch

Confer Plastics

Confer Plastics 7100X Bedienungsanleitung

Confer Plastics

Confer Plastics STEP-ENC Bedienungsanleitung

Confer Plastics

Confer Plastics 6000B Benutzerhandbuch

Confer Plastics

Confer Plastics 8100X Bedienungsanleitung

Confer Plastics

Confer Plastics ROLLGUARD 7200 Einrichtungshandbuch

Confer Plastics

Confer Plastics 635-52 Benutzerhandbuch

Confer Plastics

Confer Plastics 8000X Bedienungsanleitung

Confer Plastics

Confer Plastics 635-52X Einrichtungshandbuch

Confer Plastics

Confer Plastics ROLLGUARD 7200 Einrichtungshandbuch

Confer Plastics

Confer Plastics 6000X Einrichtungshandbuch

Confer Plastics

Confer Plastics 7000 Bedienungsanleitung

Confer Plastics

Confer Plastics CK7100-X Bedienungsanleitung

Confer Plastics

Confer Plastics 8100X Bedienungsanleitung

Confer Plastics

Confer Plastics 7100X Einrichtungshandbuch

Confer Plastics

Confer Plastics 8000 Einrichtungshandbuch

Beliebte Leiter Handbücher anderer Marken

ADVANCED SIMRACING

ADVANCED SIMRACING ASR6 Bedienungsanleitung

Batavia

Batavia GIRAFFE AIR Bedienungsanleitung

Millennium

Millennium L-220-SL Bedienungsanleitung

Louisville

Louisville AA2210 Bedienungsanleitung

wibe

wibe TMR Benutzerhandbuch

BESSLER

BESSLER 20 Bedienungsanleitung

Branach

Branach TerrainMaster Bedienungsanleitung

TUBESCA-COMABI

TUBESCA-COMABI 02271 105 à 115 Bedienungsanleitung

KTL

KTL 24392909 Handbuch

Penguin

Penguin ICE LADDER Bedienungsanleitung

KRAUSE

KRAUSE 1103 Series Bedienungsanleitung

Tractel

Tractel skysafe Gebrauchsanweisung

AFIX

AFIX FAST FIX Bedienungsanleitung

Wenger

Wenger Fixed Height Stairway 2-Step Bedienungsanleitung

KRAUSE

KRAUSE 1212 Bedienungsanleitung

fakro

fakro LWS-P 22/47 Bedienungsanleitung

FACAL

FACAL Euro Stilo Handbuch

SHEDorize

SHEDorize Stepladder/Rake/Cord Rack Bedienungsanleitung