Consort QZWP30N Handbuch

Quartz Infrared Outdoor Heaters

The following information should be considered when installing Quartz

Infrared Heaters.

Installation should always be carried out by a qualified electrician or a

competent person in accordance with current electrical regulations, protected

by a suitably rated isolator and fuse or type3 mcb.

•The heater should be mounted horizontally where possible or at a

maximum angle of 35 degrees from the horizontal using the mounting

brackets provided to ensure adequate clearances.

•

•A minimum air gap of 500mm should always be allowed between the top

of the heater and the ceiling, roof or canvas.

•A safety distance of 1mtr should always be left in front of the heater.

•Heaters should not be installed in areas where hazardous vapours may be

present as defined in BS5345

•This fitting is rated classIand IP55 suitable for outdoor use. To maintain

the protection rating all connections to the mains must be done with a

minimum of IP55 equipment.

•Ensure that there is no possibility of inflammable material coming into

contact with the heater, or is too near the heater.

The essential element of the heater is the halogen filled quartz linear lamp

with a tungsten element. This operates at about 1600°C and emits short wave

infrared radiant heat.

The lamp operates at full output almost instantly and emits a radiant energy of

1.2 – 1.6 microns.

Specifications

QZWP30N – 230 - 240V 3000W 12.5Amps Protection - IP55

Spare Lamp Each lamp is 240v 1500w Part No. HE791001

This product conforms to EU Directive 2002/96/EC.

This appliance bears the symbol of the crossed waste bin. This

indicates that, at the end of its useful life, it must not be disposed

of as domestic waste, but must be taken to a collection centre for

waste electrical and electronic equipment. It is the user's

responsibility to dispose of this appliance through the appropriate

channels at the end of its useful life. Failure to do so may incur

the penalties established by laws governing waste disposal.

INSTALLATION, OPERATION AND MAINTENANCE

INSTRUCTIONS FOR

WEATHERPROOF 3KW

QUARTZ-ZONE RADIANT HEATER

Catalogue Number QZWP30N

PLEASE RETAIN THIS LEAFLET FOR FUTURE MAINTENANCE

Consort Equipment Products Ltd

Registered Office: Thornton Industrial Estate

Milford Haven, Pembrokeshire, SA73 2RT

Tel: 01646 692172 Fax: 01646 695195

Email: technical@consortepl.com

Web: www.consortepl.com

BS EN ISO 9001 Registered Company No FM12671

After unpacking make sure that the appliance is complete and shows no signs of

visible damage or tampering.

•Keep packing materials, which are potential dangers, away from children.

•Check the supply voltage is the same as indicated on the device.

•Do not touch the heater with wet hands;

•The heater should only be used with adult supervision.

•Do not operate the heater without the guard in position.

•Avoid improper use of extension cords.

Installation

•The mains lead is made from high temperature cable and as such should not be

replaced without consulting a suitable qualified electrician.

•The Fitting must always be installed using the mounting brackets provided. This

ensures correct positioning and adequate clearance.

•This unit should be mounted at a minimum of 1800mm above ground level (see

drawing below) with a minimum air gap of 500mm maintained above the heater

and the ceiling or canopy.

•A safety distance of 1mtr should always be left in front of the heater.

•Ensure that there is no possibility of inflammable material coming into contact with

the heater, or is too near the heater.

•The fitting must be earthed.

Wall mounting

Remove the bracket from the back of the heater by unscrewing the 2 x M8

bolts.

Before drilling any holes ensure that the wall is solid and that there are no

water pipes or electrical wires in the area where you are placing the heater.

Secure the bracket to the wall then refit the heater to the bracket using the 2 x

M8 bolts.

The heater must be mounted at an angle of between 45 and 90 deg. (See

drawing opposite)

Maintenance

The heater contains no moving parts and therefore very little maintenance is

required other than to ensure that there is no excessive build-up of dust/dirt on

the reflectors or emitters as this can cause overheating and premature emitter

failure. To clean the appliance, turn off and disconnect from mains supply,

allow to cool then wipe with a damp cloth.

Lamp replacement

The lamp used in the fitting is robust and if knocks and shock vibrations are

avoided, will last for around 5000 hours.

To replace

1. Disconnect the heater from the power supply by unplugging from the

mains socket and wait until the body has cooled down.

2. Remove both end caps by undoing the 2 socket head screws at each end.

3. Remove the guard and end reflectors.

4. Unclip the lamp from the spring clips at each end, allowing the emitter to

move forward clear of the back reflector.

5. Unclip the reflector from the heater casing.

6. Disconnect the emitter wires from the terminals located in the electrical

box on the rear of the heater, and then remove the lamp.

7. Insert the wires of the new lamp through the holes in the heater body to

the electrical box and reconnect them into the terminals. Ensure that the

terminals are tightened correctly to make a good electrical connection.

8. Re-assemble making sure all the parts are replaced and the guard is in

position

36000395 Iss 01

Andere Consort Heizung Handbücher

Consort

Consort ScreenZone RAC1306 Bedienungsanleitung

Consort

Consort CSL1LST Gebrauchs- und Wartungshandbuch

Consort

Consort LST500ERF Gebrauchs- und Wartungshandbuch

Consort

Consort PLE200/SS Bedienungsanleitung

Consort

Consort FANFAIR PFH15T Bedienungsanleitung

Consort

Consort CSL2SC Gebrauchs- und Wartungshandbuch

Consort

Consort BFH2SL Gebrauchs- und Wartungshandbuch

Consort

Consort Frost Fighter Bedienungsanleitung

Consort

Consort PVSL050 Gebrauchs- und Wartungshandbuch

Consort

Consort HE7915G Gebrauchs- und Wartungshandbuch

Consort

Consort CN2MLSTiE Gebrauchs- und Wartungshandbuch

Consort

Consort LST500E Gebrauchs- und Wartungshandbuch

Consort

Consort PLSTi150RX Gebrauchs- und Wartungshandbuch

Consort

Consort PLSTI050EWIFI Gebrauchs- und Wartungshandbuch

Consort

Consort FANFAIR PFH15T Leitfaden

Consort

Consort CN1LST Leitfaden

Consort

Consort Heatsream PHRX Series Bedienungsanleitung

Consort

Consort PHSL2 Series Gebrauchs- und Wartungshandbuch

Consort

Consort LST500 Handbuch

Consort

Consort Heatflow BFH2T Montage- und Bedienungsanleitung

Consort

Consort PLSTi Series Gebrauchs- und Wartungshandbuch

Consort

Consort PLSTi050ERF Gebrauchs- und Wartungshandbuch

Consort

Consort WMH3RX Bedienungsanleitung

Consort

Consort Heatflow BHM1 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung