Consort ScreenZone RAC1306 Bedienungsanleitung

41001453 Iss 02

Consort Equipment Products Limited

Thornton Industrial Estate, Milford Haven

Pembrokeshire, A73 2RT

Tel: 01646 692172 Fax: 01646 695195

Email: technical@consortepl.com Web: www.consortepl.com

CREEN

ONE

RECESSED WARM AIR CURTAINS

ATALOGUE

UM ERS

RAC1306, RAC1309

RAC1306RX

NSTALLATION

AND

PERATING

ANUAL

INDEX Section

General Information ------------------------------------------------------------- 1

Dimensions ------------------------------------------------------------------------ 2

Installation Details --------------------------------------------------------------- 3

Electrical Connection ----------------------------------------------------------- 4

Operation -------------------------------------------------------------------------- 5

ervicing & Maintenance ------------------------------------------------------ 6

41001453 Iss 02

1.5 RX Controller Location

It is essential the Controller is positioned in the

same room as the air curtain. It should be where its

temperature will not be change with local effects.

Avoid:

• Draughty places near windows or doors

• Places near the air curtain itself or any other

heat sources in the room

• Place where the sun will shine on it

• Places where it may get wet

1.6 Controller standard models

The RAC1306 and RAC1309 heaters are supplied

with a remote controller. The remote control unit

houses 3 single pole and 1 change over 10A rocker

switches. The controller is wired to the base unit via

0.75mm² 5 core PVC flexible cable.

1.7 Clearance Distances

It is recommended that a minimum clearance of

100mm is allowed around the case and 55mm

above. The clearance allows for cable entry and

prevents combustible surfaces overheating.

The minimum mounting height (floor to grille) is 2m.

The maximum mounting height for RAC1306 is

2.8m and for RAC1309 is 3.4m.

1. General Information

1.1 Introduction

The heaters are designed for discreet positioning in

a suspended ceiling or bulkhead in the doorways of

retail or commercial premises. Overall energy sav-

ing is likely when the heater is sited above a fre-

quently opened external door as the airstream can

prevent heat loss. Will fit a recess as shallow as

195mm.

1.2 General

All installations must be in accordance with the

regulations in force in the country of use.

These instructions must be handed to the user on

completion of the installation.

Installers and service engineers must be able to

demonstrate competence and be suitably qualified

in accordance with the regulations in force in the

country of use.

To ensure continued and safe operation it is recom-

mended that the appliance is serviced annually.

The heater outlet / inlet must not be obstructed dur-

ing use.

1.3 Electrical Supply

Electrical supply for RAC1306 and RAC1309 is ei-

ther 230V single phase or 415V three phase, Neu-

tral and Earth. Max cable inlet size is 4mm² for 1 - 4

terminals and 6mm² for L and N terminals.

Electrical supply for RAC1306RX is 230V single

phase only. Max cable inlet size is 4mm².

It is recommended that the electrical supply to the

base unit in the air curtain is via an appropriate

switched isolator having a contact separation of

greater than 3mm on all poles.

BM control, time switches, room thermostats and

door interlocks can be installed at the discretion and

responsibility of the installer.

All units must be wired in accordance with I.E.E

regulations for the Electrical Equipment of Buildings

and the installer should ensure that a suitable isolat-

ing switch is connected in the mains supply.

1.4 Controller `RX` models

The RAC1306RX heater is supplied without a con-

troller. The `RX` models will not work without the

CRX2 wireless controller. ee section 5.1 for more

details.

CONSORT Wireless CRX2 controller

41001453 Iss 02

2. Dimensions

2.1 Air Curtain Dimensions

41001453 Iss 02

3. Installation Details

ENSURE AIR OUTLET LOUVRES ARE NEAREST

TO DOOR APPERTURE.

3. Installation Details

3.1 Location

All units should be installed horizontally directly

over the door opening. It is recommended that the

air curtain is installed on the inside of the building,

within the open room space against a wall or

ceiling.

Care must be taken to allow complete free air

movement into the inlet grilles of the unit to ensure

correct working operation of the air curtain. The

discharge opening should be as close to the top of

the door as possible and cover the entire door

width.

Units can be mounted adjacent to each other to

cover the full door opening across wider

entrances.

The weight of the RAC13 heaters is 17kg

3.2 Clearance Distance

It is recommended that a minimum clearance of

55mm is allowed around the case.

The minimum mounting height (floor to grille) is

1.8m. The recommended mounting height is 2.8m.

3.3 Health and Safety

ole liability rests with the installer to ensure that

all site safety procedures are adhered to during

installation.

ole liability rests with the installer to ensure that

protective safety wear such as hand, eye, ear and

head protection is used during installation of the

product.

Do not rest anything especially ladders against the

product.

Fig.1 Air discharge

Fig.2 Mounting cut out dimensions

Fig.3 Grille fixing

WARNING:

THI AIR CURTAIN HOULD NOT BE

IN TALLED WHERE THERE I A

CORRO IVE ATMO PHERE.

41001453 Iss 02

3.4 Installation

It is the sole responsibility of the installer to ensure

that the points of attachment to the building are

sound. Consultation with the consultant/architect or

owner of the building is recommended to ensure

that a sound, mechanically stable installation is

achieved.

Before fitting or wiring the air curtain, ensure the

outlet is facing the doorway as on the picture and

see the general installation guidance notes.

Using a pozidrive screwdriver slacken the two M5

screws in the corners near air inlet side and remove

the two M5 screws in opposite corner near the out-

let. lide the lid sideways until the keyhole slots

pass over the screw heads. The grille assembly can

now be removed from the case.

Each unit has 2 fixing brackets from which it is sus-

pended. The brackets may be removed to assist in

passing the air curtain through the recess then reat-

tached when in-situ.

Either drop rods or catenary wire can be used to

fasten the air curtain to the ceiling support structure.

The height between the ceiling face and the top of

the air curtain case needs to be adjusted to circa

140mm to enable the grille assembly to fit flush with

the ceiling. Adjust accordingly.

After fitting the product in the ceiling recess and ad-

justing the height to ensure that the grille sits flush

to the ceiling (when re-fitted) take the grille assem-

bly and refit using the screws removed.

4. Electrical Connections

Fig.8 Cable entry position

4.1 Electrical connections

Fig.7 Grille Earth lead

With grille removed, connect the electrical supply

and controls wiring to the appropriate terminals (see

relevant wiring diagram section).

The unit has four holes for the cable entry, two on

the top and two on the side.

Cable entry may be

moved to alternative position if desired (see Fig.8

drawing).

An EARTH lead is connected to the lid from the unit

body, push on connection at grille. When replacing

the grille onto the unit ensure the EARTH lead is re-

connected. (see Fig.7 )

3. Installation Details

Fig.4 Fixing points

Fig.5 Wire fixing

Fig.6 Rod fixing

41001453 Iss 02

4.2 Electrical connections for standard models

Fig.12 Wiring of the heaters without using remote switch

4.3 Electrical connections without using the remote switch standard models

If the heaters are to be controlled by means other than the remote switch supplied, eg BM , then

the heat output can be selected by connecting the appropriate terminals.

WIRED TERMINAL

RAC1306 RAC1309

2 +3 + 4 or 5

6000W 9000W

2 + 4 or 5

2000W 3000W

3 + 4 or 5

4000W 6000W

Please note the ‘4’ or ‘5’ terminal must always be connected

4. Electrical Connections.

L2 L3

Fig.10 Three Phase connection Fig.11 Single Phase connection

Fig.9 Remote switch wiring

ON/OFF

BOOST

HEAT I.

HEAT II.

41001453 Iss 02

5.1 Models for wireless controls

The wireless controlled model RAC1306RX can

be controlled by our CRX2 wireless controller. The

heater will not work without this controller. Each

controller has a unique identification code, it can

control an unlimited number of heaters and will not

interfere with other controllers within the building.

For more details please follow the instructions

supplied with the controller.

5. Operation.

4. Electrical Connections.

4.4 Electrical connections for wireless control models

To switch on the appliance and operate the blower,

depress the left-hand switch (marked “on/off”).

To change the fan speed use fan/boost switch.

When the heat 1 switch only (marked with a single

bar) is depressed the heat output is ⅓ of full heat.

RAC1306 - 2kW,RAC1309 - 3kW

When the heat 2 switch only (marked with a double

bar) is depressed the heat output is ⅔ of full heat.

RAC1306 - 4kW,RAC1309 - 6kW

When both heat switches are depressed the full heat

output is available.

RAC1306 - 6kW,RAC1309 - 9kW

Fig.13 ‘L’ and ‘N’ connections Fig.14 Earth connection

5.2 Standard models

All standard RAC heaters are supplied with a re-

mote switch that gives the following functions;

On/off, fan, fan boost and heat.

For thermostatic control, a room thermostat with

6A switch rating maybe connected to the circuit.

The thermostat should be wired between the ter-

minal 1 and the heater remote switch.

41001453 Iss 02

ALWAYS ENSURE THAT THE MAIN EXTER-

NAL ELECTRICITY SUPPLY IS SWITCHED

OFF EFORE COMMENCING ANY MAINTE-

NANCE ON THIS HEATER.

To obtain the best results from the heater, it is es-

sential to avoid the accumulation of dust and dirt

within the unit on the air inlet and discharge grilles.

For this reason regular cleaning is necessary, pay-

ing particular attention to the removal of dirt build up

on the rotor blades.

Cleaning of the fan is best carried out with a soft

brush.

The product should be serviced annually.

ervicing shall be undertaken by a competent per-

son.

6.2 General

If the air curtain does not operate after switching on,

then a suitably competent service engineer should

be called to identify the nature of the fault.

All Air Curtains are fitted thermal cut-outs and motor

thermal protection.

Other faults in relation to the element, motor and

wiring should be identified using conventional fault

finding techniques.

In the event that electrical components are replaced,

please ensure that electrical safety checks in accor-

dance with the regulations in force in the country of

use are undertaken.

6.3 Thermal and fault protection

The units are protected from overheating in the

event of fan failure or an obstruction of the free air-

flow by thermal cut-outs.

6. Servicing & Maintenance

6.1 Maintenance

If this happens, the thermal cut-outs effectively

switch off the appliance by disconnecting power to

the control circuit. The appliance will not operate

until the thermal cut-outs are manually reset. This

should be done by a competent electrician.

The heaters are also protected by thermal fuses to

prevent catastrophic failure. The thermal fuse will

trip and disconnect power to the affected heater.

Thermal fuses are not resettable.

6.4 Fault Conditions

If the heater will not operate, disconnect it from the

mains and arrange for a certified electrician to at-

tend to investigate the reason.

6.5 Replacing Fan Heater Assembly

Remove the lid.

Disconnect the internal wiring from the main termi-

nal block. Remove the four nuts and washers fixing

the fan heater assembly to the back of the case.

The fan heater assembly can now be eased for-

ward and removed from the heater case. Fit re-

placement fan heater and reassemble in reverse

order.

6.6 Spares

It is essential when ordering spares or replacement

parts to state the model number and the serial

number on the rating place fixed to the top of the

unit.

In the interest of progress the Company reserve the

right to vary specifications from time to time without

notice. The material listed is offered subject to the

Company’s General Conditions of ale, a copy of

which can be obtained on request.

Consort Equipment Products Ltd

Registered Office: Thornton Industrial Estate

Milford Haven, Pembrokeshire, S 73 2RT

Tel: 01646 692172 Fax: 01646 695195

BS EN ISO 9001 Registered Company No FM12671

41001453 Iss 02

Fig.18 Wiring diagram

standard models

41001453 Iss 02

Fig.19 Wiring diagram models for

wireless controls

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Consort Heizung Handbücher

Consort

Consort PLSTI050EWIFI Gebrauchs- und Wartungshandbuch

Consort

Consort CN2FSLT Gebrauchs- und Wartungshandbuch

Consort

Consort PLE050MWIFI Gebrauchs- und Wartungshandbuch

Consort

Consort QZWP15N Handbuch

Consort

Consort PLE050 Gebrauchs- und Wartungshandbuch

Consort

Consort PLSTi Series Gebrauchs- und Wartungshandbuch

Consort

Consort PRX050SS Gebrauchs- und Wartungshandbuch

Consort

Consort WMH3SL Gebrauchs- und Wartungshandbuch

Consort

Consort WMH3E Gebrauchs- und Wartungshandbuch

Consort

Consort CHELSEA WMHW3 Handbuch

Consort

Consort PLE200/SS Bedienungsanleitung

Consort

Consort CHELSEA WMH3 Handbuch

Consort

Consort CN1LSTRX Original Betriebsanleitung

Consort

Consort CSL2LST Original Betriebsanleitung

Consort

Consort BFH2SL Gebrauchs- und Wartungshandbuch

Consort

Consort RWH2S Handbuch

Consort

Consort CSL2SC Gebrauchs- und Wartungshandbuch

Consort

Consort PLE050 Gebrauchs- und Wartungshandbuch

Consort

Consort CSL1LST Gebrauchs- und Wartungshandbuch

Consort

Consort CN2MLSTiE Gebrauchs- und Wartungshandbuch

Consort

Consort CN2LSTRX Bedienungsanleitung

Consort

Consort LST500EWIFI Gebrauchs- und Wartungshandbuch

Consort

Consort LST500 Handbuch

Consort

Consort CN1LSTW Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung