Contacta HLD9 Bedienungsanleitung
1
HLD9
User Guide
October 2016
Hearing Loop Driver
2
3
Contents
Product Overview
Components
Connections
Setting up the Driver
Loop Congurations / Set Up
Troubleshooting
Technical Specication
Warranty
Standards
4
4
5-6
7-9
10-13
14-15
16
17
18
Contacta has a policy of continuous product development, therefore small specication changes
may not be reected in this manual. Images, labels, packaging, accessories and product colours
are subject to change without notice.
4
Product Overview
Components
Our HLD9 is a pioneering modular hearing loop driver for perimeter
or phased array congurations, suitable for large area applications
such as theatres, conference facilities, sports arenas, concert halls and
auditoria.
The HLD9 uses cutting edge switching converter technology to deliver
high eicacy and high performance with low noise.
1
2
3
4
5
1. User Guide
2. Hearing Loop Stickers x 2
3. Rubber Feet x 4
4. Hearing Loop Driver (HLD)
5. IEC Power Lead
You will also need: loop cable or at copper tape of a length and
type, which will be determined by the loop design. The driver requires
ancillary equipment for audio feeds, such as a microphone or sound
system. Loop test equipment is also required as detailed on page 8.
5
1. Power Supply Input.
Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. The primary method of isolating the amplier
from the mains supply is to disconnect the mains plug. Ensure that the
mains plug remains accessible at all times. Unplug the AC power cord
from the AC outlet if the unit will not be used for several months or
more.
Rear Panel Connections*:
Connections
1
23
45
67
8
*HLD9-ETL rear panel text shown. All connections
are the same on the standard HLD9.
2. External Port - Status Indicator (Volt-free relay contacts).
3. Phantom power indication for microphone.
4. Input 1 (Microphone) - Balanced XLR with switchable 12VDC
phantom power or ¼” unbalanced TRS jack for electret microphone
with 5VDC power via 680Ω load.
5. Input 2 (Line) - Balanced XLR or ¼” TRS jack to ohmically isolated
input.
6. Expansion.
CAUTION: For connection to other Contacta systems only.
7. Feature - External monitor & control, Contacta communications
processor.
CAUTION: This is not a telecommunications port.
8. NL4 Loop Output Connection.
6
Audio Connections:
2 1
3
Mic & Line
XLR connector
1: Screen/Shield
2: + (Signal Hot)
3: - (Signal Cold)
Mic
Unbalanced TRS Jack
Tip
Ring
Sleeve SOURCE
+ (Signal)
GND
Mic
Unbalanced Mono TS Jack
Tip
Sleeve SOURCE
+ (Signal)
GND
Line
Unbalanced Mono TS Jack
Tip
Sleeve
SOURCE
+ (Signal) hot
- (Signal) cold
Phantom Power
CAUTION: Route loop output cables as far away as possible from the
driver audio input cables.
Connect a twisted pair or quad core loop feeder cables to the supplied
NL4 connector (diagram below). Insert into Output Channel A/B
sockets on the rear of the driver.
Loop Connections:
7
Setting up the Driver
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
Shows MIC level Shows LINE level Shows DRIVE level
Driver Modes:
Normal Operation Mode – The driver is fully functional. However, the
controls on the front do not change the driver operation.
Adjustment Mode – In this mode one can adjust all of the levels using
the + or – buttons.
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLIN
ED
RIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
To enter adjustment mode press
both MIC + and - simultaneously
In adjustment mode the
STATUS LED will ash
Front Panel Overview:
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLIN
ED
RIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
Pressing the MIC + or - will
adjust the MIC input gain;
adjustments are in 1dB steps.
LEDs show the MIC’s level
after fader
Pressing the LINE + or - will adjust the
LINE input gain; adjustments are in 1dB
steps. LEDs show the LINE level after
fader. If input is low the LOW SIG LED
will illuminate
Pressing the Drive + or - will
adjust the Drive output by
1dB steps. LEDs show the
DRIVE level in approx 0.5A
increments
8
Engineers mode – In this mode there are additional items that can
be adjusted, such as driver type, phantom power and high frequency
compensation.
You must rst be in adjustment mode (see page 7). Then, to enter the
engineers mode, simply press both Line + and - simultaneously.
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLIN
ED
RIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
Press both Line + and - simultaneously
to enter the Engineers’ mode
PAGE 1 allows you to select the driver operation; either PERIMETER,
PRIMARY or SECONDARY. Always select the driver operation mode
before installing the driver in its rack mount bracket.
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLIN
ED
RIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
PAGE 1 is identied by
LED 1 ashing
Pressing the LINE + or - buttons
selects driver operation, Perimeter,
PRIMARY or SECONDARY
When you are ready to move
onto the next PAGE press the
DRIVE + button
There are 5 PAGE settings, each identied by a ashing MIC LED:
PAGE 1 is LED 1, PAGE 2 is LED 2, etc.
9
• Pressing the MIC (+ and -) buttons simultaneously will take the
driver back to the normal operation mode where the controls are
non-functional.
• PERIMETER mode, for a single loop or (with a secondary driver)
two widely separated loops.
• PRIMARY mode, the rst and controlling driver of two in a phased
array loop layout.
• SECONDARY mode, the second driver of two in a phased array
loop layout.
• When only this rst light is illuminated and the driver is in the
engineers mode, press either the LINE + or – to change the driver
type from PERIMETER, PRIMARY OR SECONDARY.
• When nished setting up the driver type, press the DRIVE – button
to take the driver out of the engineers mode and put if back into
the adjustment mode. The status light will begin to ash.
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
Changing the driver type
You must be in engineers mode to change the driver type.
Ensure you have selected PAGE 1.
The three operating modes are:
10
Loop Congurations / Set Up
PLEASE NOTE: The loop cable must be connected before powering up
the driver. Upon power up the loop is automatically analysed and set
up. If no loop is connected the status light will be solid red. To RESET
unplug the driver and wait 60 seconds minimum after all lights go out.
Perimeter Loop or Primary Driver Setup*
1. Power up the driver and once the loop analysis (indicated by the
ashing LED sequence) is complete, conrm or select the correct
driver type (PERIMETER or PRIMARY). Instructions on changing driver
type on page 14.
CAUTION: Once the loop (load) has been analysed it should not be
altered or adjusted
2. Enter the adjustment mode by pressing the MIC (+ and - ) buttons
simultaneously until the red status light ashes.
3. While in adjustment mode (red status light ashing) conrm that
the MIC, LINE and DRIVE levels are set to their minimum level by
individually holding in the - button of each for a few seconds.
4. Connect the input signal to the LINE input unless you are directly
connecting a microphone. If testing with our Test Signal Generator
(TSG), connect to the HLD9’s LINE input.
5. For either input signal (in adjustment mode) increase the
appropriate input level by pressing the - button until the rst yellow
LED illuminates (this will be solid if using a sine wave) or occasionally
ash if used on music or speech sources.
6. Bring the DRIVE level up by pressing the DRIVE + button until the
required level is reached.
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
CLIP
ACTIVE
PHTM
CLIP
ACTIVE
LOW SIG
STATUS
POWER
MICLINEDRIVE
PERIMETER
PRIMARY
SECONDARY
2.5 5 7.5 10
contacta HLD9
*Assumes unit is properly connected and loop has continuity.
Andere Handbücher für HLD9
1
Inhaltsverzeichnis
