Contemporary Research ICC2-IRC Bedienungsanleitung

17630 Davenport Rd, Suite113

Dallas, TX 75252 USA

Tel: 972.931.2728

888.972.2728

Fax: 972.931-2765

Web: www.crwww.com

www.contemporaryresearch.com

Product Manual

ICC2-IRC / ICW-IRC

IR TV Controller

Ver. 2.5 October 30, 2002

Contemporary Research Corporation 2 IR TV Controller

Table of Contents

Overview............................................................................................................................................. 3

Specifications...................................................................................................................................... 4

Physical .................................................................................................................................................4

Front Panel ............................................................................................................................................4

Rear Panel.............................................................................................................................................4

Internal Closures....................................................................................................................................4

RF Tuner ...............................................................................................................................................5

iCC-Net (ICC2-IRC).................................................................................................................................5

iCW-Net (ICW-IRC) ................................................................................................................................5

CC-HSD Scan Sensor ..............................................................................................................................5

Status Indication ....................................................................................................................................5

Installation ......................................................................................................................................... 6

AC Power...............................................................................................................................................6

RF Coax and iCC-Net Operation ...............................................................................................................6

iCW-Net Connection (ICW-IRC) ...............................................................................................................6

TV Power Sensing ..................................................................................................................................6

A/V Setup ..............................................................................................................................................7

IR Control Wiring ...................................................................................................................................7

IR Mode and Power Sensing....................................................................................................................7

Programming the IC-RC Remote..............................................................................................................7

On-Screen Setup Menus..........................................................................................................................8

RS-232 Control Protocol ..................................................................................................................... 9

Overview ...............................................................................................................................................9

Command String Structure ......................................................................................................................9

RS-232 Commands ........................................................................................................................... 10

RS-232 Responses ............................................................................................................................ 13

Response String Structure..................................................................................................................... 13

iC-Net Zones ..................................................................................................................................... 15

System Map ...................................................................................................................................... 16

Typical RF and ICC-Net Signal Flow ................................................................................................. 17

iCW-Net Wiring ................................................................................................................................. 18

Mounting the IRC.............................................................................................................................. 19

Safety Instructions ........................................................................................................................... 20

Limited Warranty and Disclaimer ..................................................................................................... 21

Contemporary Research Corporation 3 IR TV Controller

Overview

Contemporary Research offers two solutions for intelligent, interactive distributed media management, the

ICC2-IRC and ICW-IRC IR TV Controllers. The ICC2-IRC communicates bi-directionally over the same RF coax

that carries the broadband TV channels, dramatically simplifying system wiring. The ICW-IRC connects over a

twisted-pair network using Category 5 or Category 3 wiring and connectors.

Both IRC TV Controllers feature an internal TV tuner for absolute channel access management and a character

generator that outputs on-screen text for channel names, control functions, and interactive menus. Intelligent

tuning, volume and power control is provided by IR control port and included scan sensor. Front-panel control

and LEDs keep users in touch with their system. Enjoy a full range of control choices with the included

IC-RC IR Wireless Remote, designed for simplified control of distributed media channels and sources.

Compatible with the Contemporary Research ABC Media Retrieval System and iC Commander software, the IRC

TV Controllers can be networked with up to 4000 TV and Video Display controllers. For custom systems

applications, all IRC units and other iC-Net devices can be accessed from a single RS-232 port on ICC-HE and

ICW-HE Head-End Network Controllers.

•Controls most brands of TVs from IR control port

oCreates on-screen channel labels, messages, text menus, and feedback using onboard

character generator

oReceives wireless commands from included IC-RC IR remote from internal IR sensors, external

sensor optional

oDelivers absolute volume control for level and mute

oManages channel access using programmable available channel list

oDelivers absolute power control with included power sensor

•Networks with up to 4,000 TVs through an ICC-HE or ICW-HE Head-End Network Controller

oICC2-IRC units provide 2-way operation over the same RF cable as CATV channels

oICW-IRC connect over Category 3 or 5 wiring

oUnits instantly respond to individual, zone, and all-call commands

•Provides front-panel control for power, volume, and channel, and LED feedback for power, IR control,

and network

•Includes A/V inputs to display video from PCs, overheads, cameras and other local video sources

•Restores all operation status after loss of power from data stored in non-volatile memory

•Enables and disables front-panel control via iC-Net protocol

•Mounts above, below, or near TV, mounting brackets included over the same RF coax as the distributed

media channels, simplifying system wiring and retrofit

Contemporary Research Corporation 4 IR TV Controller

Specifications

Physical

Size: 8.5" [216mm] wide x 1.75" [38mm] height (1RU) x 6.0" [153mm] deep

Weight: 1.5 lbs [0.68kg]

Enclosure: All aluminum with durable black powder coat paint

Mounting: Mounts above or below TV, optional RK2 brackets available

Front Panel

Push Buttons: Channel up and down, Volume up and down, and Power

Power LED: Red LED lights when TV is on

Net LED: Green LED for iC-Net bus, flashes once per second if active

IR In LED: Red LED lights when receiving IR commands from remote

IR Out LED: Red LED lights when sending IR commands

Volume Up/Down: Buttons adjust volume of IRC audio output

Channel Up/Down: Buttons select list of channels stored in IRC Tune Ring

Rear Panel

Power In: 2.1mm coaxial jack (inside center conductor positive), 350 Ma maximum

11.5 to 16.5 VDC, 12 VDC typical (may be unregulated)

North American version includes UL/CSA listed wall power supply

Power Sensor: 3.5mm jack for optional CC-HSD scan sensor or 5V logic-level input

IR Out: 3.5mm jack for CC-IRE IR Emitter cable or compatible CC-IRS serial cable

Supports carrier frequencies up to 62 KHz

Shipped with CC-IRE cable, 10 foot with stick-on IR emitter

Antenna/Cable: ‘F’, female, 75 ohm impedance

A/V Inputs: Video - RCA female, NTSC composite

Audio – 2 RCA female, mono 20K ohms unbalanced

A/V Outputs: Video - RCA female, NTSC composite

Audio – 2 RCA female, mono 1K ohms, 20Hz to 20KHz

0.5% maximum, 0.1% typical THD, 500mV RMS typical at max volume

Volume control 0 to -62 dB and mute in 64 steps

IR In Mounting hole for optional external IR sensor input jack

Internal Closures

Type: 2 Solid-State output switch closures, max 50 mA, 24 VDC

Closure 1 normally used for optional buzzer

Closure 2 normally used for an external camera power relay (by others)

Available as factory-installed option only

Contemporary Research Corporation 5 IR TV Controller

RF Tuner

Frequency Range: NTSC television 55.25 to 801.25 MHz, 62.5KHZ fine tune resolution

Maximum Input: +20dBmV

Video Gain: ±5% maximum, 2% typical

Video Phase: ±3 degrees maximum, 2 degrees typical

iCC-Net (ICC2-IRC)

Operation: Carried over the same RF coax connection as TV channels

Data Receive: Mid-band VHF, 74.7MHz, sent from IC Head-End Network Controller

-25 to +35 dBmV signal level

Data Transmit: Sub-band, 5.6MHz sent to Head-End Network Controller

80 KHz max carrier deviation

+49dBmV nominal

iCW-Net (ICW-IRC)

Connector RJ-45 female 8 pin Telco jack

RS-485 type data requiring at least 2 twisted wire pairs with shield or fifth conductor

Recommended Wire: CAT3/CAT5 compatible unshielded, max 3300 feet [914m] from iC Head End

CC-HSD Scan Sensor

Range: Senses presence of TV scanning, from 15-35 KHz, magnetic pick-up

Includes: 3.5mm plug, 4ft. cable, stick-on TV sensor

Status Indication

The Net and Power LEDs have special modes that help system setup and troubleshooting.

Power LED Uses a blink mode when the IRC logic and Sensor feedback do not agree

For example, if the TV Controller knows the TV should be on, but the sensor

input does not see scanning activity, the Power LED blinks rapidly.

Net LED Blinks when it is receiving network data

LED Response

Off – DC power to IRC missing or other internal power problem

Solid On – no network communication

Blinks once per second - communicating over network

The Head-End Network Controller sends out a “heartbeat” command once every

second that will flash the Net LED.

Logic Sensor LED Response

ON ON Solid On

ON OFF Blinks – states do not agree

OFF OFF Solid Off

OFF ON Blinks – states do not agree

Contemporary Research Corporation 6 IR TV Controller

Installation

AC Power

1. Insert DC power supply plug into 12 VDC jack on the IRC.

2. Plug power adaptor into AC wall outlet.

3. The Net LED should turn on and stay lit.

RF Coax and iCC-Net Operation

1. Connect the RF Coax cable into the Antenna/Cable input on the IRC.

2. If the iCC-Net signal is operating, the Net LED will blink once per second (ICC2-IRC only).

iCW-Net Connection (ICW-IRC)

1. Plug the iCW-Net RJ-45 connector into the iCW-Net input on the ICW-IRC.

2. If the iCW-Net signal is operating, the Net LED will blink once per second.

TV Power Sensing

1. Press the Power button on the IRC.

2. The Power LED should blink, indicating that the IRC knows the TV should be on, but is not sensing the

presence of TV scanning operation.

3. Insert the CC-HSD Scan Sensor plug into the IRC Power Sensor jack.

4. Turn on the TV using the TV’s power button.

5. Move the CC-HSD sensor block around the rear of the TV to pick up scanning signal from the TV’s

horizontal transformer

6. Watch the IRC Power LED as you move the sensor, stop moving when the LED stops blinking.

7. Turn the TV on and off from its own power button, testing if the IRC is reliably sensing power.

8. Mount the sensor to the TV, using the enclosed Velcro tape.

Tip: The best location for the sensor is usually on the lower left rear corner side corner (looking

from the front), and it may help to rotate the sensor to search for best performance.

Contemporary Research Corporation 7 IR TV Controller

A/V Setup

1. Connect audio and video outputs of the IRC into the audio and video inputs of the TV.

2. You may use the left or right IRC audio output for a TV with mono audio, both for a TV with stereo audio

(IRC sound is mono).

3. Select the External Video/Aux inputs on the TV to view on-screen setup commands and A/V from the IRC

(Most TVs don’t have a discrete Video input command).

IR Control Wiring

1. Connect the CC-IRE IR Emitter plug into the IRC IR Out jack.

2. Mount the emitter cube to the TV case where the TV receives IR commands.

3. Place the IRC near the TV within line-of-sight control from the IC-RC wireless IR remote. At this point,

you could fix the IRC into the final mounting position above or below the TV, or simply place the IRC so

you can complete the IR setup procedure.

Tip: At this point, you’ve set up the control wiring, the manufacturer’s codes sent will be

programmed or changed with the On-Screen Setup Menu 45700. Press the Power button on

the IRC. If the TV turns on and off, the settings are already correct.

IR Mode and Power Sensing

Newer IRC models set the IR and Sensing options via the On-Screen Setup Menu 45702. Some ICW-IRC units

include a DIP switch (S6), located inside the IRC, to set IR options and TV Power sensing. Note this affects the

front-panel sensing, not an external IR sensor. Turning off both sensors would limit sensing to the external IR

sensor only. If you have two adjacent TVs (or one on each side of a wall), you may want to lower TV power

sensing. Some TVs prefer a lower IR output, most work fine with the standard level.

Switch # Function Options

1 38 KHz IR Receive ON= 38 KHz IR

OFF= 38 KHz IR off (default)

2 57 KHz IR Receive ON= 57 KHz IR (default)

OFF= 57 KHz IR off

3 TV Power Sensing ON= High sensitivity (default)

OFF= Low sensitivity

4 IR Control Output ON= High IR output (default)

OFF= Low IR output

Programming the IC-RC Remote

In order to complete the setup of the IRC, you’ll need the IC-RC IR Remote to use the On-Screen Menus.

Typically, the remote is shipped ready to communicate to the IRC (Code 9). Just in case, here’s how to set the

format of IR codes in the remote:

1. Press and hold the Select button and a numeric key for the code # below.

2. Release the two keys at the same time.

3. The remote will now send the selected codes.

4. Remote will keep the codes, even if battery power is lost.

IR Code Format Code

Zenith Smart TV 1

Philips Smart TV 2

RCA Smart TV 3

Contemporary Research 38 KHz 4

Contemporary Research 57 KHz (default) 9

Tip: Normally, the 57 KHz frequency works the best, avoiding most sources of IR interference.

The IRC has 38 KHz and 57 KHz sensors, so it can receive either frequency.

Contemporary Research Corporation 8 IR TV Controller

On-Screen Setup Menus

The remaining installation steps use the IR remote and the built-in character generator of the IRC.

1. Touch Menu, then 999, then Enter.

2. The text CR MENU> should appear on the screen.

3. Key in one of the commands shown below, then press Enter to activate.

4. Note that, in Menu mode, the Channel Down key acts as a backspace/delete key.

Command Function

All The following commands are used for all IRCs

45678 Display IRC firmware version

45679 Display the unit’s Device #. At this point, you can use the Channel Down key as a

Delete key, enter a new device # with the remote’s numeric keypad, then hit Enter

to save the new number.

45700 Display or edit IR device type. Sets the IR control format to match your TV. In many

cases, CR can pre-set this command to the format specified by the dealer.

0=None

1=Zenith [added V2.0]

2=Panasonic [added V1.7]

3=Toshiba [added V2.0]

4=Hitachi [added V2.0]

5=Sony [added V2.0]

6=Grundig [added V2.0]

7=Magnavox/Philips [added V1.7]

8=RCA [added V2.0]

9=Sony_2 [added V2.0]

10=Panasonic_2 [added V1.9]

11=Mitsubishi [added V2.0]

12=Monivision (old) [added V1.6]

13=Monivision (new) [added V1.8]

14=Panasonic_3 [added V1.9]

15=Sharp [added V2.1]

16=Pioneer (plasma) [added V2.3]

17=NEC (plasma) [added V2.3]

18 = Samsung [added 2.5]

45702 Set IR receive, IR output and power sensing levels.

1 = Enable 38KHz IR receive in, 0=disable

2 = Enable 57KHz IR receive in, 0=disable

4 = Enable IR output carrier, 0=no carrier

8 = Set power sensor for high sensitivity, 0=low sensitivity

16 = Set IR output for high current, 0=low current

Add up the values and enter the result. For example, the default setting is 30 (57

KHz on, IR carrier, high power sensitivity, and high IR output).

65478 Reset IRC, similar to disconnecting power then restarting.

65487 Initialize IRC to factory default settings: Power on, unlocked, display channel 11,

channel ring set to 4, 5, and 11, Group 0. Note that this command works even if TV

power is off or control is locked out.

65482 Shows Net RX if receiving the iC-HE’s “heartbeat” pulse once per second, !NET RX

if not. Also displays receive signal strength in the ICC2-IRC.

ICC2-IRC The following commands are used for the ICC2-IRC only

65480 Enable constant Net transmit to the Head-End. This is used for measuring the signal

strength of the ICC2-IRC’s RF output. Press Enter to stop transmitting, or the unit

will automatically stop after 50 seconds.

65481 Display ICC2 transmitter frequency control voltage – should be 2000 - 3150.

65483 Display DF transmitter frequency deviation – should be 245 - 300.

Contemporary Research Corporation 9 IR TV Controller

RS-232 Control Protocol

Overview

RS-232 control for up to 4000 ICC2-IRC and ICW-IRC TV Controllers is provided through an iC-series Head-End

Network Controller. The ICC-HE Head-End manages iC-Net communication over RF Coax to ICC2-IRC TV

Controllers as well as ICW-IRC TV Controllers over twisted-pair Cat3/5 wiring. The ICW-HE Head-End operates

on the twisted-pair network only.

Each TV Controller is assigned a unique device number from 1 to 4000 to which control commands are

addressed. The devices are organized into 16 zones of 255 devices. All the devices in each zone will respond to

a single “virtual device number” — one device number that represents all devices in each zone. There is also a

global device number, 4095, that will command all devices in the system. This feature dramatically speeds up

system operation and programming, because one command can affect an entire group of devices—or all. To

take advantages of this feature, review the section iC-Net Zones in this manual.

In ABC Media Retrieval Systems, we reserve the first group of devices, 1-255, for components operating on a

connected control system. Zones 1-16 are used for CR TV Controllers, Video Display Controllers and Tuners. As

it’s unlikely any system will use all 4000 devices, this may be a good device standard for your system as well.

The Remote RS-232 port on the Head-End Network Controller can communicate from 1200 to 38.4K baud. The

factory default setting is 19.2K baud, 8 data bits, No parity, and 1 stop bit.

Command String Structure

Characters in command strings are expressed in a combination of hex and ASCII characters. For clarity, the

following protocol examples use the following conventions:

•Single-byte hex numbers are preceded by the ‘$’ symbol

•ASCII characters or strings are enclosed in single quotes

•Numbers not marked as hex or ASCII are a single decimal byte

•Parameters shown in < > brackets are single byte

•A series of multiple commands or parameters are set apart by [ ] brackets

•Commas separate the bytes, but are not part of the protocol

•Double quotes enclose the command string, but are not part of the protocol

Command format:

“$A5,<dh>,<dl>,<ncb>,<cmd1>,<parameter> [<cmdN>]"

$A5 Starts the command

<dh> The zone or high order byte of the device

<dl> The unit or low order byte of the device (0 for global zone)

<ncb> The number of command bytes to follow

<cmd1> The first command byte

<parameter> Command parameters (not used by all commands)

[<cmdN>] Multiple commands can be concatenated, with byte count added to <ncb>

Contemporary Research Corporation 10 IR TV Controller

RS-232 Commands

Command Description

Power Off PO “$A5,<dh>,<dl>,2,’P0’ ” (6 bytes) – checks sensor for true power control

Power On P1 “$A5,<dh>,<dl>,2,’P1’ ” (6 bytes) – checks sensor for true power control

Power Toggle PT “$A5,<dh>,<dl>,2,’PT’ ” (6 bytes) – checks sensor for true power control

Operating

Parameters

TM “$A5,<dh>,<dl>,3,’TM’,<setting>” (7 bytes)

Sets up key functions in the IRC

bit 7 – 3 = 0

bit 2 – Channel up/down operation, 0=Tune Ring, 1=Send IR Keypad response

bit 1 – Numeric channel labels, 0=num labels off, 1=num labels on)

bit 0 – Alpha channel labels, 0=alpha labels off, 1=alpha labels on

Volume

VL “$A5,<dh>,<dl>,3,’VL’,<vol level>” (7 bytes)

Sets IRC volume level

0 = Mute

1 – 63 = Minimum level (1) to maximum volume (63)

Power-up

Volume

S5 "$A5,<dh>,<dl>,3,'S5',<volume>" (7 bytes)

Sets volume level when IRC powers up

0 = restore to previous level

1 – 63 = Set from minimum (1) to maximum level (63)

Ts & Qs

T-series channel commands select a channel and display the channel label on the TV,

while Q-series commands don’t show the on-screen text.

T Channel Up TU “$A5,<dh>,<dl>,2,’TU’ ” (6 bytes) – Tunes to next channel up in Tune Ring

T Channel Dwn TD “$A5,<dh>,<dl>,2,’TD’ ” (6 bytes) – Tunes to next channel down in Tune Ring

Force T Channel TC “$A5,<dh>,<dl>,3,’TC’, <channel>” (7 bytes) – Tunes to a specific channel

124 = RGB 2 input on TV

125 = RGB input on TV

126 = Select IRC external A/V input (also selects TV video input)

127 = Select S-Video Input

0 = Blank video output to TV

255 = Unblank TV video (restore to previous channel)

Tip: Not all inputs are available on every TV make and model.

Select T Channel TT “$A5,<dh>,<dl>,2,’TT’ ” (6 bytes) – Tunes channel if included in Tune Ring

Channel Query T? “$A5,<dh>,<dl>,2,’T?’ ” (6 bytes) – Request response for current channel

Q Channel Up QU “$A5,<dh>,<dl>,2,’QU’ ” (6 bytes) – Tunes to next channel up in Tune Ring

Q Channel Dwn QD “$A5,<dh>,<dl>,2,’QD’ ” (6 bytes) – Tunes to next channel down in Tune Ring

Force Q Chan QC “$A5,<dh>,<dl>,3,’QC’, <channel>” (7 bytes) – Tunes to a specific channel

Same special-function channels as in the T Channel Select section above

Select Q Chan QT “$A5,<dh>,<dl>,2,’TT’ ” (6 bytes) – Tunes channel if included in Tune Ring

Andere Handbücher für ICC2-IRC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Contemporary Research Controller Handbücher

Contemporary Research

Contemporary Research ICC1-232 Bedienungsanleitung

Contemporary Research

Contemporary Research ICC1-232 Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-ZS2 Bedienungsanleitung

Contemporary Research

Contemporary Research ICA-FT6 Bedienungsanleitung

Contemporary Research

Contemporary Research ICC1-IR Bedienungsanleitung

Contemporary Research

Contemporary Research ICC1-ZS2 Anleitungen und Rezepte

Contemporary Research

Contemporary Research ICC1 Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-PSC Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-PSC Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-PSC2 Anleitungen und Rezepte

Contemporary Research

Contemporary Research ICW-ZS2 Bedienungsanleitung

Contemporary Research

Contemporary Research VCC Benutzerhandbuch

Contemporary Research

Contemporary Research VCC Bedienungsanleitung

Contemporary Research

Contemporary Research ICW-STA Bedienungsanleitung

Contemporary Research

Contemporary Research ICC2-VDC Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-PRZ Bedienungsanleitung

Contemporary Research

Contemporary Research ICC-ZS2 Anleitungen und Rezepte

Contemporary Research

Contemporary Research ICC1-232 Bedienungsanleitung

Contemporary Research

Contemporary Research ICW-IRC Benutzerhandbuch

Contemporary Research

Contemporary Research ICC2-VDC Bedienungsanleitung

Contemporary Research

Contemporary Research ICC1-IRX Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung