Control Products HC-110 Series Bedienungsanleitung
Custom Design
• Membrane touch-pad programming
• 0.56" high red LED display
• Programmable setpoint(s) and differential(s)
• Panel mount enclosure
The HC-110 series panel mount humidity controllers provide
humidity display, relay control, and feature programmable setpoints,
upper and lower setpoint limits, differentials and calibration.
Applications
Applications include computer rooms, HVAC,
food service, medical, agricultural and industrial equipment.
Specifications
General Description
Features
• Available with single or dual stages
• Humidity setpoint display
• LED relay status indicator(s)
• Tamper resistant programmable setpoint limits
Relay(s) contact rating: SPDT relay, 4 Amp
(24 VAC resistive)
Ambient temperature range: 20° to 158°F,
– 6° to 70°C
Humidity: 90% non-condensing
Agency approvals: U.L. and C.U.L. recognized
Weight: 3.6 oz. (0.1kg)
Power requirements: Available in 12 or 24 volt models -
Specify AC (2VA) or DC (100 mA) voltage supply
Sensor: Not included (see HS 50 series or HS 800 series
specifications)
Accuracy: +3% (depends on accuracy of sensor)
Relay status indicator: Lighted while relay is activated
SET
%RH
ADJUST
>
hidden
button Cutout Dimensions
N0 C NC NO C NC G S +5 –3 – +
+ = volt (white)
Input
Power
SP-2 SP-1
(32mm)
(3mm)
3.22"
relaystatusindicator
Sensor
1.51"
(82mm)
1.27"
(64mm)
2.533" (79mm)
3.1"
(38mm)
1.51" (34mm)
1.35"
0.125"
(38mm)
HUMIDITY CONTROLLERS
HC–110
G= ground (black)
– = ground (black)
S= signal (white)
+5= VDC (red)
–3 = factory
>
Dimensions & Wiring
1724 Lake Drive West • Minneapolis, MN 55317 • 612-448-2217 FAX 612-448-1606 • Made in USA
Innovative Technologies in Custom Electronic Design & Manufacturing
Programming Instructions
IMPORTANT: If the programming sequence is interrupted for more than 15 seconds or not completed to the blank
screen stage, the unit will automatically revert to the humidity display mode WITHOUT acknowledging any
new values (tamper resistant feature).
B. DIFFERENTIAL(S), HIGH/LOW SETPOINT LIMITS AND CALIBRATION – To program these parameters, press
the "hidden" button located behind the "%RH" symbol (instead of the SET button), and repeat the programming
procedure described in step A.
1. Differential "dIF" – setting a positive differential value will close the NO (normally open) relay(s)
on humidity fall (humidification applications) and open the relay(s) on humidity rise. A negative differential
setting will close the NO relay(s) on humidity rise (dehumidification applications) and open the relay(s) on
humidity fall. Differential is programmable from –30% to +30%. DO NOT SET DIFFERENTIAL AT "0".
2. High and Low Setpoint Limits "HI" and "LO" – allow you to limit the range in which the setpoints can
be programmed. Also, by programming the high and low setpoint limit values to the same number, a
tamper-resistant fixed setpoint is established.
3. Calibration "CAL" – Controller calibration can be programmed +30%. Unit is factory calibrated to a
certified standard.
A. SETPOINT(S) 1. To start the programming sequence, press the SET button once. Unit displays "SP1" (setpoint 1).
2. Press the SET button again to display SP1 value.
3. To program an increase or decrease in SP1, press the appropriate ADJUST arrow.
4. Repeat steps 1 thru 3 for SP2 (setpoint 2, dual stage model only).
5. To complete the programming sequence, press the SET button until the screen
goes blank. After five seconds, the unit will automatically display sensor humidity.
Please use the following example when ordering:
HC = Humidity Controller
HC – 110 S – 24VAC
Ordering Information
In addition to standard models, Control Products specializes in complete custom design of electronic controls.
Modifications of standard controls such as wire length and guarded access are also available. Please consult factory
for more information.
Custom Design & Modifications
S or D
S = single stage
D = dual stage
110 series
Rev. 5-95
Control Products, Inc. warrants its products to be free from defects in material and workmanship under normal use for
one year and is not responsible for consequential damages or installation costs of any nature. Exposure to contaminants
and extreme environmental conditions such as moisture, temperature, chemicals, etc. may cause the unit to degrade or
fail. Control Products accepts no liability for product applications or customer application testing.
Warranty
Supply Voltage Options
24 = VAC
24VDC = 24 VDC
or
12 = VAC
12VDC = 12 VDC
Andere Control Products Temperaturregler Handbücher
Beliebte Temperaturregler Handbücher anderer Marken
Swegon
Swegon LUNAd MB Bedienungsanleitung
Lucky Reptile
Lucky Reptile Thermo Control II Bedienungsanleitung
SENSORMETRIX
SENSORMETRIX Argon 100 Bedienungsanleitung
Fuji Electric
Fuji Electric PXE4 Bedienungsanleitung
Yuyao gongyi
Yuyao gongyi XMT-808 series Bedienungsanleitung
Selec
Selec TC544C Bedienungsanleitung
