CONVECTAIR Piccolo 7831 Montageanleitung

!"#

!""#$#

!%&'())('*+%,-,

#./0('*%1,!%&'023'*+%&

!!"#!$%#&'&()*+,-./0&/)&1-&2-3/&14&-.56+-7

421AA2357 Ind.A

INTRODUCTION :

Dear owner,

- Congratulations on the purchase of this premium electric heater. CONVECTAIR develops and

produces the highest quality heating product in the electrical industry.

- To obtain the best results and the ultimate in performance and comfort, please take a moment to

read the installation , operation and maintenance instructions detailed in this manual

QUICK START GUIDE .................................................................................................. Page 3

1- SPECIFICATIONS......................................................................................................... Page 4

2- RECOMMENDED SET-UP..................................................................................... Page 4

3- INSTALLATION AND MOUNTING.............................................................. Page 5

4- ELECTRICAL CONNECTION.............................................................................. Page 7

5- OPERATING INSTRUCTIONS........................................................................... Page 9

6- OVERHEAT CONTROL........................................................................................... Page 10

7- MAINTENANCE.. ........................................................................................................ Page 10

8- TROUBLESHOOTING ............................................................................................. Page 11

9- IDENTIFICATION OF YOUR HEATER ......................................................... Page 11

10- WARRANTY INFORMATION ........................................................................ Page 11

TABLE OF CONTENTS

WARNING :

Your heater is already equiped with a precise electronic thermostat. It must not be

connected to a wall thermostat.

- QUICK START GUIDE -

Electrical requirements : 240 V

Installating and connecting the heater

To turn the heater ON or OFF

To set the temperature

Fast heat

Trouble shooting page 10

To contact Convectair : see page 10

See pages 6 and 7.

See pages 5, 6 and 7.

Press the switch brieﬂy

Set the temperature dial at the comfort zone. Wait for the temperature to stabilize.

Adjust up or down for the required comfort level (see page 8).

With the heater ON, press the button.

On/Oﬀ indicator

On/Oﬀ switch

ermostat adjustment

Accelerated heat ventilation

button (30 minutes)

Accelerated heat ventilation indicator

Comfort zone

Heating indicator

Fig. 1

SPECIFICATIONS

- Your new PICCOLO is a fan heater partially enclosed.

- is heater is equipped with 2 fan forced heat levels : 750W regulated with the electronic

thermostat and 1500W accelerated heat on demand for 30 minutes.

- Minimum obstruction and designed to heat your room quietly, consistant heat, it is a per-

fect heater for your bathroom or other intermittant rooms.

- Your PICCOLO can be used with the optional CONVECTAIR Programmer Module (pilot

wire) allowing scheduled temperature set-backs in periods of prolonged absence providing

the same comfort and more savings.

READ CAREFULLY : :

These instructions are essential to install and use your new PICCOOLO safely.

!RECOMMANDED SET-UP

- Your heater must be installed in accordance with national and local codes and CONVECTAIR

recommends an installation by a qualiﬁed electrician.

- Your heater must be installed so that the control panel is out of reach from anyone in the

bath-tub or in the shower. Do not install over a bath-tub or spa.

- Do not install the heater behind a door, furniture or others obstacles, or in front of an airex-

haustvent. Keep combustible materials such as curtains, away from the heater.

- Your heater is equipped with a heating element that may reach high temperatures. Do not

install or operate in the presence of gasoline, paint solvents or other ﬂammable products.

- Maintain the minimum required clearances ( height from ﬂoor, distances from side walls or

furniture, drapes, etc).

"INSTALLATION AND MOUNTING

- Identify where you want to install the heater, providing suﬃcient clearance around the unit

(Fig.2).

- e PICCOLO heater is partially enclosed and clearance restrictions must be respected (Fig.

2).

e heater should be installed no lower than 30 cm (12 in.) from the ﬂoor. Leave a minimum

clearance of 10 cm (4 in.) on each side of the heater, 20 cm (8 in.) and 60 cm (24 in.) in front for

a proper air circulation.

- Clear a rectangular opening of 37.2 cm (143/5 in.) high, 31.5 cm (123/8 in.) wide and 8,5 cm (33/8

in.).Deep between the dreams of the wall (Fig. 3).

- Make sure that the electrical wires (and the pilot wire if needed) come out of the top left corner

of the wall opening (Fig.3).

- The heater can be dismantled in 3 pieces (Fig.3) :

the front facade (1), the ventilation block and panel

controls (2) and the built-in (3).

To dismantle the heater :

- Take off the facade by removing the 2 screws located

on the panel control and the 2 screws located at the

bottom of the facade (Fig. 4).

- Take off the ventilation block by removing the 2

screws (Fig. 5, A) and slide the ventilation block to

click the hooks (Fig. 5, B).

Electrical wire exit

- Before placing the inner junction box inside the wall opening, remove the knock out and

pass the electrical wires (Fig.6), and the pilot wire if needed, using an appropriate bushing

( not include).

- Insert the inner box and secure it to the wall having taken into account the reassembly of the

facade. Indeed, leave approximately 3 mm (1/8“) between the wall and the upper fold of the

inner box to facilitate the assembly of the facade (see Fig. 7a et 7b).

Power cable

wall

Facade

Inner

Box Screw

Screw

- Insert and hook the ventilation block and the protocol panel inside the inner box. Secure the

ventilation box with 2 screws (Fig.5).

- Connect the electrical wires ( see chapter 4 - connexion, page 7).

- When remounting the front facade, please make sure that the low small strip of the facade

(Rep.A) amounts down of the deﬂector of ventilation block (Rep.B), and this to guarantee

optimal performances.

- Place and hook the facade using the inner box

crease. Secure the control panel using 2 screws

and then secure the facade with 2 screws (Fig.4).

WARNING : Do not pinch wires when closing

the facade.

- Aﬁx the control panel sticker provided in the

bag (Fig.8) and put the control wheel in place.

BAD GOOD

#ELECTRICAL CONNEXION

- CONVECTAIR recommends that your heater be installed by a qualiﬁed

electrician and in accordance with national and local codes.

- To prevent short circuits and electrical shocks turn the power oﬀ at the main

panel before attempting the installation or making any repairs.

- If the power cable is damaged it must be replaced by the manufacturer, an

approved service depot or a technician with similar qualiﬁcations to avoid any danger.

- e connection of the heater must be done inside the inner box on the left side

of the control panel. Connect the wires using the wire connectors provided in the

bag (Fig.9).

CAUTION :

is heater must be connected to a 240 Volt (60 cycles) circuit.

- Disconnect the power supply before making wiring connections to prevent

electrical shock and equipement damage. If you are using a programmer system,

make sur to cut the power oﬀ ALL electrical heating circuits in the home (for more

information, see the CONVECTAIR model 7392 installation notice).

RESPECT WIRE COLOR WIRING

- You must connect the ground wire of the heater ( Green /

Yellow) with the copper wire.

- e purple wire with the seal at the extremity should not

be used for the electrical connexion.

- e purple wire is used only if the heater is connected with

the CONVECTAIR central programming system.

$OPERATING INSTRUCTIONS

On/Oﬀ indicator

On/Oﬀ switch

ermostat adjustment

Accelerated heat ventilation

button (30 minutes)

Accelerated heat ventilation indicator

Comfort zone

Heating indicator

e electronic controls have been designed to achieve maximum savings.

- Once the heater is on, set the temperature dial at the comfort zone.

- Close the doors and windows the room where the heater is located. Let the temperature

stabilize for an hour.

- If the temperature is not quite right, adjust the thermostat dial up or down by half a mark.

- Let the temperature stabilize for another hour before checking again and repeat if necessary

(with a quarter adjustement this time).

- Once the thermostat is set at the desired comfort setting, do not touch the thermostat dial.

To turn the heater oﬀ, use the On/Oﬀ switch. To brieﬂy raise the temperature, use the accele-

rated heat ventilation button.

Accelerated heat

When activating the accelerated heat, the Piccolo provides temporarily 1500W, allowing to warm

more quickly the room.

- When the heater on, press the accelerated heat ventilation button to obtain 1500W for a 30

minutes duration. The accelerated heat ventilation indicator turns on.

- To revert to standard operating mode, press the accelerated heat ventilation button.

- When the accelerated heat ventilation cycle is finished, the heater resumes normal heating mode

(750W).

%OVERHEAT CONTROL

- is heater is equipped with overheat controls. In case of a malfunction of the unit (blocked

air output or intake, for example) the heater will stop heating automatically. After correcting

the malfunction the heater can be reset.

To restart the heater:

- Turn the heater oﬀ and turn its power supply oﬀ. Check that the front outlets are free of

obstruction. Wait 5 minutes and turn the heater back on.

If no heat is generated, call your electrician or the nearest CONVECTAIR repair center.

MAINTENANCE

- To keep your CONVECTAIR unit clean, regular maintenance is suggested. To remove dust,

use a soft cloth. To remove a stain, use a damp cloth. For a better performance and maximum

eﬃciency, it is suggested that dust and lint be regularly removed from the protective grill

situated at the back of your PICCOLO.

NEVER USE ABRASIVE OR ACETONE-BASED PRODUCTS TO CLEAN YOUR HEATER AS THIS

MAY DETERIORATE THE EPOXY FINISH.

!"#$%&'()$'*)+$&'%"'$',")%&!-

Your CONVECTAIR heater will become hot when in use. Caution is advised when young children are present.

Do not insert small objects in the heater : this could cause an electrical short circuit, ﬁre or damage to the

inner components.

Any use or modiﬁcations not approved by CONVECTAIR may cause electrical short circuits, ﬁre or injuries to

the users.

In certain cases, it is possible for yellowing of the surface to occur over time. is is not due to a manufacturing

defect.is is caused by surrounding air, which may contain smoke or dust, being heated and circulated

through the heater.

Prevention : it is suggested that surfaces be frequently cleaned especially with units installed in

locations where cigarette smoke is present or in the kitchen. Never use this heater during construction

work or other activities that generate a lot of dust.

ANY REPAIR ON YOUR CONVECTAIR HEATER SHOULD ONLY BE DONE BY A QUALIFIED TECHNICIAN,

AND ONLY AFTER HEATER HAS BEEN DISCONNECTED.

)*!

Inhaltsverzeichnis

Andere CONVECTAIR Heizung Handbücher

CONVECTAIR

CONVECTAIR opera 12 7732-C07 Handbuch

CONVECTAIR

CONVECTAIR Allegro 7300-C07 Kurzanleitung

CONVECTAIR

CONVECTAIR DIVA 7648 Bedienungsanleitung

CONVECTAIR

CONVECTAIR DIVA 7647 Montageanleitung

CONVECTAIR

CONVECTAIR ALLEGRO II Bedienungsanleitung

CONVECTAIR

CONVECTAIR ALTO 7375 C Bedienungsanleitung

CONVECTAIR

CONVECTAIR CALYPSO 7826 Bedienungsanleitung

CONVECTAIR

CONVECTAIR SOPRANO Installationsanleitung

CONVECTAIR

CONVECTAIR Allegro 26 7304 Handbuch

CONVECTAIR

CONVECTAIR Samba Bedienungs- und Wartungshandbuch

CONVECTAIR

CONVECTAIR 7359 - C05 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung