Cookology CEI1100SS Bedienungsanleitung

CEI1100SS

CEI110WGP CEI110BGP

Cooker hood

Instruction manual

CONTENT

1……………………………………….Notice

2……………………………………….Feature

3………………………………………..Installation

4………………………………………..Notice of installation

5………………………………………..Safety Warning

6…………………………………………Speed adjustment

7…………………………………………Maintenance

8…………………………………………Abnormity and Solution

1.Notice

This appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or lack

of experience and knowledge if they

have been given supervision or

instruction concerning use of the

appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

The instructions shall state the

substance of the following:

– there shall be adequate ventilation

of the room when the range hood is

used at the same time as appliances

burning gas or other fuels (not

applicable to appliances that only

discharge the air back into the room);

– the details concerning the method

and frequency of cleaning;

– there is a fire risk if cleaning is not

carried out in accordance with the

instructions;

– do not flambé under the range hood;

– CAUTION: Accessible parts may

become hot when used with cooking

appliances.

The installation instructions shall

include the substance of the

following:

– the air must not be discharged into a

flue that is used for exhausting fumes

from appliances burning gas or other

fuels (not applicable to appliances

that only discharge the air back into

the room);

– the minimum distance between the

supporting surface for the cooking

vessels on the hob and the lowest part

of the range hood. (When the range

hood is located above a gas appliance,

this distance shall be at least 65 cm.

– regulations concerning the

discharge of air have to be fulfilled.

The installation instructions for range

hoods with accessible metallic

enclosures of class II construction

shall include details that indicate the

location and maximum permitted

lengths for any fixing or mounting

screw or other fixing device that

penetrates into the range hood to

attach an accessory such as a facia or

duct fitting.

Where fixing or mounting screws, or

other fixing devices are used, that

penetrate into the range hood with an

accessible metallic enclosure of class

II construction, to attach an accessory,

the instructions shall indicate the

required location of these screws or

fixing devices and include the

substance of the following warning.

Warning: Failure to install the screws

or fixing device in accordance with

these instructions may result in

electrical hazards.

2. Feature

1. The cooker hood uses high quality materials, and is made with a

streamlined design.

2. Equipped with a large power low noise electric motor and

centrifugal leaf, it produces strong suction, low noise, non stick grease

filter and easy to clean.

3. Special wind tunnel construction and oil collector design, free dirt

will be absorbed in a second.

3. Installation

MOUNTING OF THE V-FLAP

If the cooker hood does not have an assembled V-flap 1, you should

mount the half-parts to its body. The images only show an example of

how to mount the V-flap, the outlet may vary according to different

models and configurations.

To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6

• the pin 3 should be top oriented;

• the axis 4 should be inserted into the holes 5 on the body;

• repeat all the operations for the 2nd half-part

INSTALLATION

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should not be placed at a distance of no more than

150cm from the cooking surface for the best performance. Refer to Pic

3. The ceiling must bear at least 120KGs weight, and the thickness of the

ceiling must be ≥30MM.

4. According to the size shown on pic 2, drill 14pcs φ8mm holes on the

ceiling once the installation height is determined,14pcs explode screws(or

14pcs ST6*40mm big flat screws+14pcs wall plugs) will be used to fix

the two hanging board on the ceiling.( see pic. 3)

5. Calculate the length of the angle iron (refer to pic 4/5),then 32pcs of

M4*10 screws and M4 nut with gasket will be used to connect the angle

iron into the adjustable angle iron bracket. (Make sure the overlap length

of angle iron cannot less than 36mm)

6. As pic 9 shown, choose the direction of the outlet①/②/③/④

a. Refer to Pic 7, open the decorative plate in order, and take out the filter.

b. Refer to Pic 8, unscrew and take away the 4 pcs ST4*8mm screws that

on the panel decorative strip.

c. Unscrew the 8pcs machine silk from the bottom of the cabinet housing

and rotate it by 90°/180°/270° to choose the direction of the outlet, then

screw the 8 pcs machine silk to fix the housing well;

d. Install the panel decorative strip and filter well apply to the reverse

order of a/b steps above. Meanwhile, install the expansion pipe to the

outlet (refer to pic 10).

7. As pic 11 shown, connect the 4 adjustable angle iron bracket with the

housing by 8pcs M4*12mm

machine silk screw, next refer to

pic 12/13, lift up the housing, use

8pcs M4*12mm machine silk screw

and M4 nut with gasket to fix the

housing onto the 2 hanging board,

meanwhile, pull the expansion pipe

outside. (Note: The expansion pipe

must be fixed on the housing

firmly.)

8. After installing the housing to the hanging board, use cross screwdriver

or straight screwdriver to adjust the screw of the angle iron bracket, direct

the housing level position and height till it is suitable. Adjust method:

Adjust rang of the angle iron bracket is 0-25mm, clockwise twist the

screw of the 4 angle iron bracket, slightly move the housing upwards;

meanwhile, anticlockwise twist the screw of the angle iron bracket,

slightly move the housing downwards. Use the cross screwdriver to screw

the safety screw tightly after the level position and height is suitable.

(Refer to pic 14)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cookology Dunstabzugshaube Handbücher

Cookology

Cookology CDD600BK Bedienungsanleitung

Cookology

Cookology LINT1001BK Bedienungsanleitung

Cookology

Cookology BUCH520SS Bedienungsanleitung

Cookology

Cookology ANG605SS Bedienungsanleitung

Cookology

Cookology CEI1100BK Bedienungsanleitung

Cookology

Cookology PREM900BK Bedienungsanleitung

Cookology

Cookology TEL600SS/A Bedienungsanleitung

Cookology

Cookology CYL351BK Bedienungsanleitung

Cookology

Cookology CHA600BK Bedienungsanleitung

Cookology

Cookology HICYL351BK Bedienungsanleitung

Cookology

Cookology CGL100BK Bedienungsanleitung

Cookology

Cookology CH600SS Bedienungsanleitung

Cookology

Cookology BUGL520BK Bedienungsanleitung

Cookology

Cookology VISOR600SS Bedienungsanleitung

Cookology

Cookology VER601BK Bedienungsanleitung

Cookology

Cookology TUB350SS Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch