CoolGear CG-4PU3MGD Bedienungsanleitung
1
4 Port Managed USB 3.2 Gen 1 Hub w/
15KV
ESD Surge Protection
Model No. CG-4PU3MGD
Thank you for purchasing this 4-port Managed USB3.2 Gen 1 hub. The Super-speed
Hub is supplied with managing software utilities which can turn on/off the bus
power of each downstream device or even reset the entire hub by user or
application programs. It enables the success of your critical USB applications
instantly and improve your investment returns.
Features:
✓Compliant with USB Specification 3.2 Gen 1
✓Metal Case, DIN Rail and wall mountable
✓Software Manageable Bus power for each Port
✓Supports software utilities for Windows (XP and newer), Mac OS and Linux
✓Provides 4 Downstream USB3.2 Gen 1 Facing Ports (see Note 1)
✓Provides 4 LEDs Indicating each bus power states
✓Supports 5Gbps (Super-speed), 480Mbps (High speed), 12Mbps (Full-speed) and 1.5Mbps
(Low-speed) Speed
✓Supports 15KV ESD Level 4 Protection for Each Port
✓Supports +7~48V DC Wide Range Input Power
✓Supports USB Battery Charging v1.2 : CDP, DCP modes
1. Introduction
4-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
2
1. USB-A Downstream Facing Port Connectors: There are 4 USB-A
connectors for standard USB3.2 Gen 1 and legacy USB2.0/1.1 devices.
Note 1: The last USB port (Port 4) of this hub does NOT
support USB2.0/1.1 devices because it is used to communicate
with the managing utilities. However, it still supports USB3.2
Gen 1 devices.
2. USB-B Upstream Facing Port Connector: The Type-B connector from
upstream USB3.2 Gen 1 port. It is connected from host or another
USB3.2 hub’s downstream facing port.
3. Power LED: Turns on indicates the hub was powered.
4. Port State Indicator LEDs: Each port has a LED next to it. When the
LED is on, the USB device is enabled (connected). If the LED is off, the
USB device is disabled (disconnected).
5. Self Power Input Connector: This 2-pin (one pin is for the positive
voltage and the other pin is GND) screw-lock terminal blocks is used
2. Connector Layout
Power LED
USB-A Downstream Ports
Upstream Port
Connector
Power Input
Connector
4-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
3
to connect wide range power source to self-power the hub, the voltage
can be in the range from +7V to 48V DC.
1. Use static electricity discharge precautions.
Remove possible static discharge potential from any objects that the
hub may come in contact with before installation. This can be
accomplished by touching a bare metal chassis rail after you have
turned off the power.
2. Apply DC power (range from +7V to 48V) to the 2-pin Screw-Lock
Terminal Block Connector.
Warning!!
Please make sure the polarity of the input power should
correctly match with the marking next to the terminal block
pins
⚫The terminal blocks’ Push-In mechanism allows you to push the
wire directly into the contact hole and latched by its internal latch
spring automatically.
⚫To remove the wire, you need a tool (such as a small flathead
screwdriver) to release the internal latch spring then remove the
wire as the following picture. If the wire is too soft to be inserted
into the contact hole, you need to release the latch string with
above tool, insert the wire then release the latch spring to latch the
wire.
3. Hardware Installation
4-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
4
3. Connecting USB Host cable: The host cable can be a standard B-to-
A or B-to-C USB3.2 Gen 1 cable (depends on the host port’s connector
type). Please connect the type-A (or Type-C) end connector of the
cable to your USB host port, then connect the type-B end connector
to this hub. Since the USB hub is plug-and-play, you don’t have to turn
off your host computer when installing the hub.
4. Connect the USB devices to the downstream ports of this hub.
5. Mount your hub on the wall or DIN RAIL if required.
6. Install the USB Hub Administrator Utilities as described in the
following chapter
DIN RAIL Clip
Wall mounting holes
4-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
5
The Hub supports managing utilities called USB Hub Administrator for
major recent Windows (XP and above) and Linux:
1. The above folders include the software for different platforms.
If you are installing it on Windows, please find the executable
setup program in Windows folder, double-click it:
4. USB Hub Administrator Utilities Installation
4-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
6
2. Please follow the on-screen instructions of the setup program
to complete the installation. After installed, it will launch the
utility automatically:
⚫Click Auto Search to find all Managed USB Hubs
⚫Click the item on the list to select the Hub to control
⚫Click on the numeric (indicate the Port number) button to
turn On/Off the USB port
⚫You can save the current port states by clicking the Save
Port States button
4-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
7
3. To use the console utility CUSBC to control the USB devices,
please run Command Prompt as follows:
To see all CUSBC commands, type:
CUSBC /?
To query all Hubs connected:
CUSBC /Q
4-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit
8
To perform a factory reset:
1. Verify that your hub’s Power LED is off.
2. On the side of your hub, locate the hole of the Restore Factory
Settings button:
3. Use a paper clip or similar object to press and hold the Restore
Factory Settings button, while still holding the button power on the
hub.
4. Release the Restore Factory Settings button.
5. Your hub resets to its factory default settings:
⚫All ports are On
⚫The password: pass
Operating temp.: 0 to 55C (32 to 131F)
Operating humidity: 5 to 95% RH
6. Environmental Specifications
5. Restore to Factory Settings
Push button hole to
restore the factory
default settings
4-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit
9
Dimensions (LxWxH): 5.61(L) x 2.56(W) x 1.03(H) in
(142.5 x 65.2 x 26.3mm)
Inhaltsverzeichnis
Andere CoolGear Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
