Cooper Lighting INVUE IMI-575 Bedienungsanleitung

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

ARM & FIXTURE INSTALLATION

Bishop Arm (VA6005-VA6008, VA6054-VA6057, VA6105-VA6108

& VA6154-VA6157)

See Figure 1.

1. Secure arm onto pole and orient.

2. Tighten the six set screws located near bottom of arm to

150 in/lbs. to secure arm.

3. Loosen the three arm cap set screws and remove arm cap.

4. Pull fixture leads through arm to arm cap location.

5. Raise fixture to arm aligning locating pin and socket.

See Figure 2.

6. Insert and tighten 4 fixture screws with Teflon washers, provided

in polybag, to 80 in/lbs.

7. Connect fixture leads to service leads.

8. Resecure arm cap with arm cap set screws tightened to

50 in/lbs.

Traditional Arm (VA6009-VA6021 VA6058-VA6070,

VA6109-VA6121 & VA6158-VA6170)

See Figure 3.

1. Slip arm onto pole and orient.

2. Tighten the six set screws located near bottom of arm to

150 in/lbs. to secure arm.

3. Loosen the three arm cap set screws and remove arm cap.

4. Pull fixture leads through arm to arm cap location.

5. Raise fixture to arm aligning locating pin and socket.

See Figure 2.

6. Insert and tighten 4 fixture screws with Teflon washers, provided

in polybag, to 80 in/lbs.

7. Connect fixture leads to service leads.

8. Resecure arm cap with arm cap set screws tightened to

50 in/lbs.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-575 AVU040300

Epic/Pole Mounted

Fixtures

Sheet 1 of 4

2/18/04 IMI-575

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

General: Upon receipt of fixture thoroughly inspect for any

freight damage, which should be brought to the attention of

the delivery carrier. Compare the catalog description listed

on the packing slip with the fixture label on the housing to

assure you have received the correct merchandise.

Safety: This fixture must be wired in accordance with

the national electrical code and applicable local codes

and ordinance. Proper grounding is required to insure

personal safety. Carefully observe grounding procedure

under installation section. All work should be done by a

qualified electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Fixture Screws

Fig. 1

Teflon Washers

Arm Cap

Set Screws

Bishop Arm

Aligning Pin

Aligning Socket

Fig. 2a

Modern Top

Customer First Center •1121 Hwy 74 South •Peachtree City, GA 30269 IMI-575 AVU040300

Epic/Pole Mounted

Fixtures

Sheet 2 of 4

2/18/04 IMI-575

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

FIXTURE MAINTENANCE

A. Relamping

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Install suitable lamp. Consult re-lamp label and lamp

instructions for details. Do not overtighten.

4. Raise door and secure with screws.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining

ring and globe. Components are not tethered.

See Figure 5.

2. Install suitable lamp. Consult re-lamp label and lamp

instructions for details. Do not overtighten.

3. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use

the mark on globe bottom for orientation.

B. Starter and Fuse Replacement (Where applicable)

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Loosen thumbscrew until rectangular washer can be rotated

90 degrees. See Figure 6.

4. Rotate reflector faceplate to release from screws using key

hole slots.

5. Unplug optic quick-disconnect.

6. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

7. For starter replacement, remove the plug-in starter from

receptacle and replace.

For fuse replacement, unscrew fuse holder cap and replace

fuse. Resecure fuse holder cap.

8. Resecure the ballast cover with the two screws.

9. Plug optic quick-disconnect and secure reflector by keyhole

slots and thumbscrew.

10. Raise door and secure with screws.

Aligning Socket

Fig. 2b

Aligning Pin

Classical Top

Fixture Screws

Teflon Washers

Fig. 3

Arm Cap

Set Screws

Traditional Arm

Door Screws

Fig. 4a Options

FG, FR, SG & FRS

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

Customer First Center •1121 Hwy 74 South •Peachtree City, GA 30269 IMI-575 AVU040300

Epic/Pole Mounted

Fixtures

Sheet 3 of 4

2/18/04 IMI-575

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining ring

and globe. Components are not tethered.

See Figure 5.

2. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

3. Unplug optic quick-disconnect.

4. For starter replacement, remove the plug-in starter from

receptacle and replace.

For fuse replacement, unscrew fuse holder cap and replace

fuse. Resecure fuse holder cap.

5. Plug optic quick-disconnect.

6. Resecure the ballast cover with the two screws.

7. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use the

mark on globe bottom for orientation.

C. Power Pack Replacement

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Loosen thumbscrew until rectangular washer can be rotated

90 degrees. See Figure 6.

4. Rotate reflector faceplate to release from screws using key

hole slots.

5. Unplug optic quick-disconnect.

6. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

7. Unplug service quick-disconnect.

8. Holding the handle, loosen the two screws holding the power

pack to the fixture housing. See Figure 8.

9. Holding the handle, rotate the power pack until free and lower.

10. Holding replacement power pack by handle, raise onto screw

heads and rotate.

11. Tighten the two screws while holding power pack in position.

12. Plug together the service quick-disconnect.

13. Resecure the ballast cover with the two screws.

14. Reconnect optic quick-disconnect and secure reflector by

keyhole slots and thumbscrew.

15. Raise door and secure with screws.

Tether

Door Screws

Fig. 4b Options

FG, FR, SG & FRS

Ring Retaining Screws

Fig. 5a

Globe Retaining Ring

Globe

Option MA

Ring Retaining Screws

Fig. 5b

Globe Retaining Ring

Globe

Options

3R & 5R

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

Customer First Center •1121 Hwy 74 South •Peachtree City, GA 30269 IMI-575 AVU040300

Epic/Pole Mounted

Fixtures

Sheet 4 of 4

2/18/04 IMI-575

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining

ring and globe. Components are not tethered.

See Figure 5.

2. Remove two screws on ballast cover followed by ballast

cover. See Figure 6.

3. Unplug optic quick-disconnect.

4. Unplug service quick-disconnect.

5. Loosen the two screws holding the power pack to the

fixture housing. See Figure 7.

6. Holding the power pack by the handle, rotate the power

pack until free and lower.

7. Holding replacement power pack by handle, raise onto

screw heads and rotate.

8. Tighten the two screws while holding power pack in

position.

9. Plug together the service quick-disconnect.

10. Plug together the optic quick-disconnect.

11. Resecure the ballast cover with the two screws.

12. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use

the mark on globe bottom for orientation.

Keyhole Slot

Fig. 6

Rectangular Washer

Thumbscrew

Reflector

Removal

Ballast Cover

Screws

Optic

Quick-

Disconnect

Fig. 7a

Starter

Fig. 7b

Handle

Fuse

Service

Quick-Disconnect

Screws

Fig. 8

Power Pack Removal

Andere Cooper Lighting Landschaftsbeleuchtung Handbücher

Cooper Lighting

Cooper Lighting 902-PT CS Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Street Works TMU40SWW3SF Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere Aspen 1900-AA Bedienungsanleitung

Cooper Lighting

Cooper Lighting Avenue ARC25MWW5552 Bedienungsanleitung

Cooper Lighting

Cooper Lighting ARC15SWW33112 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Streetworks Generation Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Breckenridge MPB50SR255 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Landau MFT91MWWFT4 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HMX High-Mast Bedienungsanleitung

Cooper Lighting

Cooper Lighting SURE-LITES CCX20RWH Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCGRAW-EDISON GAR Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites STL StairLite Bedienungsanleitung

Cooper Lighting

Cooper Lighting OVY15SWW2D4 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumark LQL1500 Bedienungsanleitung

Cooper Lighting

Cooper Lighting ADH080747 Leitfaden

Cooper Lighting

Cooper Lighting Invue 42 - 175W Bedienungsanleitung

Cooper Lighting

Cooper Lighting Invue Bedienungsanleitung

Cooper Lighting

Cooper Lighting Acorn ANE50SR2554 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO H2522 Bedienungsanleitung

Cooper Lighting

Cooper Lighting McGraw-Edison PSL Bedienungsanleitung

Cooper Lighting

Cooper Lighting OVZ50SR22E4 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Westminster WST50SR2554 Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Bedienungsanleitung

Cooper Lighting

Cooper Lighting Avenue ARC25MWW5C652 Bedienungsanleitung

Beliebte Landschaftsbeleuchtung Handbücher anderer Marken

Intex

Intex SL1006 Bedienungsanleitung

LED Group

LED Group ROBUS R2IN13W Bedienungsanleitung

Patriot Lighting

Patriot Lighting 343-1484 Bedienungsanleitung

LIGMAN

LIGMAN JET 44 Bedienungsanleitung

Hess

Hess SERA G: SERA S Bedienungsanleitung

LIGMAN

LIGMAN MALTA 1 Bedienungsanleitung

Saxby Lighting

Saxby Lighting Islay 68784 Handbuch

LIGMAN

LIGMAN EU-10016-3 Bedienungsanleitung

LIGMAN

LIGMAN KI-60475 Bedienungsanleitung

Malibu Boats

Malibu Boats CL905K Bedienungsanleitung

LIGMAN

LIGMAN NYB-30161 Bedienungsanleitung

LIGMAN

LIGMAN SI-80021 Bedienungsanleitung

Volt

Volt 2-in-1 Tiki-Brass Torch Light Bedienungsanleitung

Malibu Boats

Malibu Boats CM110P Bedienungsanleitung

LIGMAN

LIGMAN VIENNA 1 Bedienungsanleitung

LIGMAN

LIGMAN LA-60022 Bedienungsanleitung

LIGMAN

LIGMAN EU-10016-2 Bedienungsanleitung

HEPER

HEPER ZEROX Hybrid Montage- und Bedienungsanleitung