Cooper Lighting Combolight Trimless V90229-1N Bedienungsanleitung

JBOX

JBOX COVER

SCREW

DRYWALL

HOUSING

TRIMLESS

INSERT

MUDDING

COMPOUND

DRYWALL SCREW

MOUNTING

CHANNEL

BUTTERFLY

MOUNTING

BRACKET

HEX

SCREW

APERTURE

COLLAR

TRIMLESS INSERT

HOUSING

Figure 1

OUTER ALIGNMENT HOLES

FIXTURE MOUNTING:

1. First remove TRIMLESS INSERT from Housing by pulling straight out.

See Fig 1. Fixture must be mounted using either BUTTERFLY MOUNTING

BRACKETS or HANGER BARS (Contact RSA Dealer for HANGER BARS).

Figure 4

ELECTRICAL:

7. Remove the JBOX COVER from the JBOX by removing the four SCREWS.

Connect supply lead wires to junction box lead wires in accordance with

your local electrical code(s) or N.E.C. Replace JBOX COVER onto JBOX,

securing with SCREWS. See Fig 3.

Figure 3

CEILING MATERIAL INSTALLATION:

8. A clean, square hole in the CEILING MATERIAL must be cut. Install the

ceiling material below housing as seen in Fig 4.

9. Replace the TRIMLESS INSERT into the HOUSING by pushing until flush

with the CEILING MATERIAL as seen in Fig 4. Using the OUTER

ALIGNMENT HOLES on the TRIMLESS INSERT, screw the TRIMLESS

INSERT into the HOUSING using DRYWALL SCREWS into the Outer

Holes on the TRIMLESS INSERT.

10. Smooth out MUDDING COMPOUND / TAPE from around aperture to

surrounding areas of DRYWALL as seen in Fig 4.

INSTALLATION NOTE:

DO NOT install insulation within 3in of any part of the Luminaire.

Blinking light of this thermally protected Luminaire may indicate overheating.

BUTTERFLY MOUNTING:

2. Fixture comes equipped with universal BUTTERFLY MOUNTING

BRACKETS that can take common 1" or 1-1/2" black iron or galvanized

MOUNTING CHANNELS (supplied by others). See Fig 2.

3. Position fixture so the MOUNTING CHANNELS lie on top of the ceiling

runners.

4. Fasten MOUNTING CHANNELS securely to ceiling runners.

5. Secure MOUNTING CHANNELS to universal BUTTERFLY MOUNTING

BRACKETS with wire tie downs.

6. The BUTTERFLY MOUNTING BRACKETS are height-adjustable and

should be set so that the APERTURE COLLAR will be flush with the

finished ceiling plane.

Figure 2

INSTALLATION INSTRUCTIONS

V90229-1N

Avoid Fire or Electric Shock

COMBOLIGHT

TRIMLESS

Page 1 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









COVER

RING

BACK RING

COIL SPRING

LAMP

(MR16 shown, COIL

SPRING behind)

BACK RING

SOCKET ASSY

PIVOT JOINT

(FOR GIMBAL

TIGHTENING)

OPTICAL

ACCESSORY

RETAINER

RING

COVER

RING

SNOOT

Flush Position

Regressed Position

CEILING

LINE

11. Lamp installation:

To install LAMP, remove the COVER RING by pushing straight back on

the COVER RING and then turning it

counter-clockwise

to release.

See Fig. 5.

12. Once removed, insert the properly-specified LAMP into the

BACK RING, ensure that the LAMP is the correct LAMP for the SOCKET

or damage to the fixture or lamp may occur. The LAMP will seat into the

COIL SPRING when installed properly. While holding the LAMP in place,

grab the SOCKET ASSY and plug or screw the LAMP firmly into it.

See Fig. 6.

Figure 7

Figure 6

(Cover Ring Removed)

Figure 8

Figure 5

13. Optical Accessory: (skip to Step 21 if not using optical accessories)

To install OPTICAL ACCESSORY pieces, remove the ACCESSORY

RETAINER RING by unthreading until it is completely removed from the

COVER RING.

14. Install desired OPTICAL ACCESSORY pieces into the COVER RING and

re-thread the ACCESSORY RETAINER RING firmly. See Fig. 7.

*The COVER RING can accommodate three (3) accessories without the

ACCESSORY RETAINER RING or two (2) pieces with it.

*The ACCESSORY RETAINER RING may be used to lock the accessory.

For example, a linear spread lens or cross baffle can be locked in-place

into a desired orientation.

*Please note that not all accessories are compatible with each other and

with all lamps.

15. Regressed Lamp Ring/Snoot: (skip to Step 19 if not regressing the lamp)

The lamp ring may be installed in a regressed position only if a

SNOOT accessory is being used. See Fig. 8. If necessary, please see step

13 for instructions on SNOOT installation. To accomplish the regressed

lamp ring position set the COVER RING aside. Remove the lamp ring assy

by loosening the two (2) SET SCREWs in the GIMBAL BLOCKs.

16. Once loosened the lamp ring assy can be removed by grasping the

GIMBAL RING and turning

clockwise

until it releases from the GIMBAL

BLOCKs.

INSTALLATION INSTRUCTIONS

V90229-2

Avoid Fire or Electric Shock

COMBOLIGHT

LAMPHOLDER

Page 2 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









GIMBAL BRACKET

(Standard Position)

SLOT

SET SCREW

SNOOT

GIMBAL RING

GIMBAL

BLOCK

17. Once removed, flip the two (2) GIMBAL BRACKETs around (180°) and

tighten the joint if necessary. See Fig. 9.

If necessary, please see Step 21 for gimbal tightening instructions.

18. Reinsert the lamp ring assembly by turning it

counter-clockwise

into the

SLOTs on the GIMBAL BLOCKs. Re-tighten the two (2) SET SCREWs

in the GIMBAL BLOCKs. The lamp ring assy should now be oriented in

the "up position". See Fig. 10.

BAYONET

SLOTS

COVER

RING

BACK RING

COVER RING

(AS INSTALLED)

GIMBAL BRACKET

(Rotated 180° to

"Down" Position)

19. To replace the COVER RING:

Push the COVER RING onto the BACK RING by lining up the

BAYONET SLOTS (see Fig. 11) with the two (2) PINs in the BACK RING.

Figure 10

Figure 11

Figure 12

Figure 9

20. Once lined up, push straight back until the COVER RING stops, then

while keeping the COVER RING pushed back, turn

clockwise

until it

pushes forward again slightly. See Fig. 12.

21. Gimbal tightening instructions:

The lamp ring is intended to give positive tension at the PIVOT JOINTS

so the lamp ring can be aimed by hand and held in place by tension.

*If a stronger, more secure lock is required then the PIVOT JOINTS (hex

screws) may be tightened

clockwise

with a hex wrench tool. See Fig. 6.

*Please note that in some conditions the COVER RING will need to be

removed to gain access to the inner PIVOT JOINTS.

INSTALLATION INSTRUCTIONS

V90229-3

Avoid Fire or Electric Shock

COMBOLIGHT

LAMPHOLDER

Page 3 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









Inhaltsverzeichnis

Andere Cooper Lighting Leuchte Handbücher

Cooper Lighting

Cooper Lighting EC Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX G SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRiS M32T Bedienungsanleitung

Cooper Lighting

Cooper Lighting COMBOLIGHT MLU Series MLU314 Bedienungsanleitung

Cooper Lighting

Cooper Lighting YR Bedienungsanleitung

Cooper Lighting

Cooper Lighting Combolight Galleria Series AR111 12V Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metal Halide PAR Lamps MD6X Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites EUX Bedienungsanleitung

Cooper Lighting

Cooper Lighting NEO-RAY 2-S Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux RK Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting all-pro mst27920les Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L10230 Bedienungsanleitung

Cooper Lighting

Cooper Lighting P1R Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L5056 Stasis Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo Classic Pendant Lighting Bedienungsanleitung

Cooper Lighting

Cooper Lighting Quiet Ceiling Trimless QCT-1975 Bedienungsanleitung

Cooper Lighting

Cooper Lighting RKS-140RS-48-10B Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo H2HALOLRG Bedienungsanleitung

Cooper Lighting

Cooper Lighting CORELITE Traverse Wall 2T5HO Bedienungsanleitung

Cooper Lighting

Cooper Lighting ALL-PRO Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting AMETRIX ADY080863 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Cirque 6-ADP Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo H1BSMLRG Bedienungsanleitung

Cooper Lighting

Cooper Lighting SURE-LITES UN Series Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung

ArtFox

ArtFox Beam 15R extreme Bedienungsanleitung