Cooper Lighting Corelite Bedienungsanleitung

WARNINGS

1). WARNING! Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

2). WARNING! - Risk of Fire/Electric Shock. If not qualiﬁed, consult an electrician.

3). WARNING! – Risk of ﬁre or electric shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when

drilling for installation of reﬂector kit hardware. Check for enclosed wiring and components.

4). WARNING! – Avoid contact with LED modules.

NOTES

1). NOTE! - This product must be installed in accordance with the applicable installation code by a certiﬁed

electrician, familiar with the construction and operation of the product and hazards involved.

2). NOTE! - Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit

installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

3). NOTE! - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.

4). NOTE! - Disconnect all power before proceeding.

5). NOTE! - “Doghouse” component on end of ﬁxture is intended for T8 lamping only. A maximum of (8) ﬁxtures can be

mounted in a continuous row with each “Doghouse” facing the opposite direction starting from the center of the run.

Class R6 LED or Fluorescent

Installation Instructions - page 1 of 2

Corelite 18001 East Colfax Ave. Aurora, CO 80011 Ph. (303) 393-1522 Fax (303) 393-1477

ADE111698 rev 021213

1. Unpack ﬁxture from box.

3. To install ﬁxture into grid, raise it through an adjacent cell and then into the cell

where it is to be installed.

5. After securing ﬁxture tabs to grid frame, use holes in tabs to tie ﬁxture back to

structure at all four corners or per local code.

2. If installing an LED ﬁxture, leave the lens installed during installation. If install-

ing a ﬂuorescent module, the lens should be left installed until just prior to

installing lamps.

4. Bend all four side tabs out and secure ﬁxture to grid.

6. Make appropriate wire connections adhereing to local electrical code.

If installing an LED ﬁxture,

this is the ﬁnal step. If

installing a ﬂuorescent

ﬁxture, go to page 2.

WARNINGS

1). WARNING! Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

2). WARNING! - Risk of Fire/Electric Shock. If not qualiﬁed, consult an electrician.

3). WARNING! – Risk of ﬁre or electric shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when

drilling for installation of reﬂector kit hardware. Check for enclosed wiring and components.

4). WARNING! – Avoid contact with LED modules.

NOTES

1). NOTE! - This product must be installed in accordance with the applicable installation code by a certiﬁed

electrician, familiar with the construction and operation of the product and hazards involved.

2). NOTE! - Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit

installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

3). NOTE! - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.

4). NOTE! - Disconnect all power before proceeding.

5). NOTE! - “Doghouse” component on end of ﬁxture is intended for T8 lamping only. A maximum of (8) ﬁxtures can be

mounted in a continuous row with each “Doghouse” facing the opposite direction starting from the center of the run.

Class R6 Fluorescent

Installation Instructions - page 2 of 2

Corelite 18001 East Colfax Ave. Aurora, CO 80011 Ph. (303) 393-1522 Fax (303) 393-1477

ADE111698 rev 021213

1. Remove lens.

3. Replace the lens.

2. Insert T5 or T8 ﬂuorescent lamp into the ﬁxture. For T8 lamping, install one

end of the lamp into the socket inside the “doghouse” compartment ﬁrst. Then

install the other end and make sure the lamp is secure.

Dieses Handbuch passt für folgende Modelle

Andere Cooper Lighting Arbeitsleuchte Handbücher

Cooper Lighting

Cooper Lighting SURE-LITES Photoluminescent Exit Signs Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRIS E4LWW Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCL5 Bedienungsanleitung

Cooper Lighting

Cooper Lighting PQS45 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites CCX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting PQS45 Bedienungsanleitung

Cooper Lighting

Cooper Lighting McGraw-Edison EPL/DLS Envoy Bedienungsanleitung

Cooper Lighting

Cooper Lighting PHL300 Bedienungsanleitung

Cooper Lighting

Cooper Lighting LED120 Bedienungsanleitung

Cooper Lighting

Cooper Lighting McGraw-Edison IMI-6950 Bedienungsanleitung

Cooper Lighting

Cooper Lighting LED110 Bedienungsanleitung

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

PowerSmith

PowerSmith PWLD080T Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

Monzana

Monzana Gore MZCL10 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung