Corecess 3213 Bedienungsanleitung

| FCC Part 15 Notice |

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Class B limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy, and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is not guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•Reorient the receiving antenna.

•Increase the separate between the equipment and the

receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician

for help.

CAUION: Changes or modifications not expressly

approved by the manufacturer responsible for

compliance could void the user's to operate the

equipment.

| Copyright |

No Part of this book shall be reproduced, stored in a

retrieval system, or transmitted by any means, electronic,

mechanical, photocopying, recording, or otherwise,

without written permission from the publisher.

The specifications and information regarding the products

in this manual are subject to changed without notice.

| Trademark Credit |

Corecess 3213 is registered trademark of Corecess Inc.

Windows is registered trademark of Microsoft Corp.

Corecess Inc.

997-4, Daechi-dong, Kangnam-ku, Seoul, Korea

TEL:82-2-3016-6900 FAX:82-2-3016-6622

http://www.corecess.com

All manuals and user guides at all-guides.com

all-guides.com

English

Table of Contents

Introduction ··························································· 4

Unpacking the Box ··············································· 4

Installing the Corecess 3213 ································ 5

Configuring the TCP/IP ········································ 7

Troubleshooting ·················································· 10

Technical Specifications ····································· 12

Thank you for using the product of Corecess.

This manual helps users to install and configure

the Corecess VDSL Modem Corecess 3213.

All manuals and user guides at all-guides.com

Corecess 3213 Installation Guide

Introduction

The Corecess 3213 is an Very-high-data-rate Digital Subscriber Line (VDSL) modem used for

home connectivity to an VDSL service provider network over an Ethernet network connection. The

Corecess 3213 VDSL modem can transmit and receive data at rates up to 16Mbps.

Unpacking the Box

Check the shipping carton carefully to ensure that the contents include the items you ordered.

Note : The PC with Ethernet port or adapter is neccssary to install the Corecess 3213.

Before installing the Corecess 3213, prepare a PC with Ethernet port or adapter.

Installation Guide

Corecess 3213

Power Supply and

Power Cord

Ethernet Cable

(Straight-through Category-5)

VDSL Cable

(RJ-11 Telephone Cable )

All manuals and user guides at all-guides.com

English

Installing the Corecess 3213

Connecting Cables

nConnecting the VDSL Line (LINE Port)

Connect the provided VDSL cable to the LINE port of the Corecess 3213 and then connect the

other end of the cable to the wall receptacle.

oConnecting a Telephone (PHONE Port)

Connect a telephone cable to the PHONE port of the Corecess 3213 and then connect the

other end of the cable to your telephone.

pConnecting a PC (LAN Port)

Connect the provided Ethernet cable to the LAN port of the Corecess 3213 and then connect

the other end of the cable to Ethernet port on the back of your PC.

qConnecting the Power Supply (DC IN Port)

Connect the provided power supply cable into the DC IN port of the Corecess 3213.

rConnecting the Power Cord

Connect the provided power cord to the power supply and connect the other end of the cord to

an appropriate electrical outlet.

Caution : You must power on the Corecess 3213 before powering on your PC. If you power

on your PC first, PC’s IP address may not be properly assigned. In this case, assign new IP

address referring to ‘Troubleshooting’ on page 10-11 or restart your PC.

All manuals and user guides at all-guides.com

Corecess 3213 Installation Guide

Power on the Corecess 3213

After connecting the Corecess 3213, turn on the Corecess 3213 by pressing the power switch on

the rear panel of the Corecess 3213.

When you have powered up the Corecess 3213, check the status of the four LEDs on the front

panel by the following table:

LED Color Status Description

POWER ON DC power is being supplied to the Corecess 3213.

LINK ON The modem is connecting to VDSL network.

LAN ON The LAN port is connecting to Ethernet port on your PC.

DATA

Green

Blink Data is being sent to or received from VDSL network.

All manuals and user guides at all-guides.com

English

Configuring the TCP/IP

After you install the Corecess 3213, next is to configure the TCP/IP network protocol.

Caution: When you configure the TCP/IP, leave the default value of any other configuration

that is not mentioned in the following description.

Windows 95/98/ME

1. Click the Start button and select Settings ¼Control Panel.

(Figure 1)

2. Double-click the Network icon.

3. Select TCP/IP in the ‘The following network components are installed’ list and click Properties.

(Figure 2)

4. Select the [IP Address] tab and click the Obtain IP address automatically. (Figure 3)

5. Select the [DNS Configuration] tab and click the Disable DNS. (Figure 4)

6. Select the [Gateway] tab and check there is no gateway

installed. If there are installed gateways, delete them by

clicking [Remove]. Click OK.(Figure 5)

7. At the <Network> dialog box, click OK.The system

prompts you to restart. Click Yes.

Figure 2 Figure 3Figure 4

Figure 5

Figure 1

All manuals and user guides at all-guides.com

all-guides.com

Corecess 3213 Installation Guide

Windows 2000/NT

1. Click the Start button and select Settings ¼Network and

Dial-up Connections. (Figure 1)

2. Right-click the Local Area Connection icon at the

<Network and Dial-up Connections> windows and select

Properties menu. (Figure 2)

3. At the <Local Area Connection Properties> dialog box, select the Internet Protocol (TCP/IP) in

the ‘Components checks are used by this connection’ list and click Properties.(Figure 3)

4. At the <Internet Protocol (TCP/IP Properties)> dialog box, click the Obtain an IP address

automatically and the Obtain DNS server address automatically. Then click Advanced to check

the TCP/IP settings for accuracy. (Figure 4)

5. The <Advanced TCP/IP Settings> dialog box appears. At the [IP Settings] tab, check that the IP

Address is set to Enable DHCP. (Figure 5)

6. Select the [DNS] tab and check that the Append primary and connection specific DNS suffix is

selected. Click OK. (Figure 6)

Figure 3Figure 4

Figure 1

Figure 2

Figure 5Figure 6

All manuals and user guides at all-guides.com

English

Windows XP

1. Click the Start button and select Settings menu. (Figure 1)

2. Double-click the Network icon at the <Control Panel>

window.

3. Right-click the Local Area Connection icon at the <Network

Connections> windows and select Properties menu. (Figure 2)

4. At the <Local Area Connection Properties> dialog box, select

the Internet Protocol (TCP/IP) in the ‘This connection uses the

following items’ list and click Properties. (Figure 3)

5. At the <Internet Protocol (TCP/IP) Properties)> dialog box, click the Obtain an IP address

automatically and the Obtain DNS server address automatically. Then click Advanced to check

the TCP/IP settings for accuracy. (Figure 4)

6. The <Advanced TCP/IP Settings> dialog box appears. At the [IP Settings] tab, check that the IP

Address is set to Enable DHCP. (Figure 5)

7. Select the [DNS] tab and check that the Append primary and connection specific DNS suffix is

selected. Click OK. (Figure 6)

Figure 3Figure 4

Figure 2

Figure 5Figure 6

Figure 1

All manuals and user guides at all-guides.com

Corecess 3213 Installation Guide

Troubleshooting

If you cannot connect to VDSL network, please check the status of the LEDs on the front panel,

and then ensure the following:

1. Check the LAN LED

If the LAN LED goes off, ensure that the Ethernet cable is firmly connected both to the Ethernet

port on the Corecess 3213 and LAN port on your PC.

2. Check the LINK LED

If the LINK LED blinks continuously and never stays solid on, ensure that the VDSL cable is

firmly connected to the LINE port on the Corecess 3213. If the LINK LED still blinks, contact

your VDSL service provider.

If the LINK LED goes off, turn off the power of the Corecess 3213 by pressing the power switch

and turn on the power again. If LINK LED still goes off, contact your vendor.

3. Check your PC’s IP address

If all LEDs operate normally and cables are firmly connected to the ports, ensure that your PC’s

IP address is properly assigned. Otherwise assign a new IP address according to your

operating system.

Windows 95/98/ME

nClick the Start button and select Run.

oInput Winipcfg and press the [Enter]

key.

pSelect Ethernet adapter connected with

the Corecess 3213 and click Release All.

qClick Renew All.

All manuals and user guides at all-guides.com

English

Windows 2000/NT/XP

nClick the Start button and select Run.

oInput cmd and press the [Enter] key.

pThe DOS-prompt appears. Input ipconfig

/release and press [Enter] key.

qInput ipconfig /renew and press [Enter]

key.

4. Restart your PC

If new IP address is not assigned properly or you cannot solve the problem, ensure that the

Corecess 3213 turns on and then restart your PC.

All manuals and user guides at all-guides.com

Andere Handbücher für 3213

Inhaltsverzeichnis

Andere Corecess Modem Handbücher

Corecess

Corecess 3213 Bedienungsanleitung

Corecess

Corecess 3312 Betriebsanleitung

Corecess

Corecess 3221 Bedienungsanleitung

Corecess

Corecess Corecess 3115 Bedienungsanleitung

Corecess

Corecess 3113 Bedienungsanleitung

Corecess

Corecess 3311 Bedienungsanleitung

Corecess

Corecess 3121 Bedienungsanleitung

Corecess

Corecess 3213 Bedienungsanleitung

Corecess

Corecess 3311N Bedienungsanleitung

Corecess

Corecess 3311N Bedienungsanleitung

Corecess

Corecess DX3111 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung