Coremorrow E52 Series Bedienungsanleitung

E52 Series Piezo Controller

User Manual

Version: V1.0

This document describes the following products:

E52.B1S-H Servo piezo controller(standard version)

E52.B1S-I Servo piezo controller(simplified version)

E52.A1K-H Open loop piezo controller

声明

Declaration!

This user manual is a integrated user manual of the E52 series piezoelectric controller. Please

read this user manual carefully before using this controller. Follow the instructions in the manual

during use. If there is any problem, please contact us for technical support. If you do not follow

this manual or disassemble and modify the product yourself, the company will not be liable for any

consequences arising therefrom.

Please read the following to avoid personal injury and to prevent damage to this product or any

other product connected to it. In order to avoid possible hazards, this product can only be used

within the specied range.

Notice!

Do not touch any exposed ends of the product and its accessories.

There is high voltage inside. Do not open the case without permission.

Do not connect or disconnect input, output, or sensor cables with power on.

Please keep surface of E52 clean and dry, don't operate in humid or static environment.

After use, output voltage should be cleared to zero before turning o󰀨 the controller switch, such as

switching the servo state to the open-loop state.

Danger!

The piezoelectric power amplier described in this manual is a high-voltage device capable of

outputting high currents, which can cause serious or even fatal damage if not used properly.

It is strongly recommended that you do not touch any parts that connect to the high voltage output.

Special Note: If you connect it with other products in addition to our company, please follow the

general accident prevention procedures.

Operating the high-voltage amplication requires training professional operators.

Cautious!

Warning!

If the voltage exceeds the PZT's tolerable range, it will cause permanent damage to the PZT.

Before adding voltage to the PZT poles, it must be ensured that the positive and negative poles

of the PZT are connected correctly and the operating voltage is within the allowable range of this

PZT.

E52 housing should be installed on a horizontal surface in an area with a 3CM air ow area to

prevent internal convection in the vertical direction.

Insu󰀩cient airow can cause equipment to overheat or premature instrument damage.

DECLARATION

1.Security ………………………………………………………………………………………………………………………… 2

1.1 Features ………………………………………………………………………………………………………………… 2

1.2 Applicaitons …………………………………………………………………………………………………………… 2

1.3 Order information…………………………………………………………………………………………………… 2

2. Driving Principle ………………………………………………………………………………………………………… 2

3.Appearance ………………………………………………………………………………………………………………… 3

4. Frequency Load Curves ……………………………………………………………………………………………… 4

5.Interface ……………………………………………………………………………………………………………………… 4

6.Power Calculation ………………………………………………………………………………………………………… 5

7. Notes and Suggestions ……………………………………………………………………………………………… 6

8. Maintenance, Storage, Transportation ………………………………………………………………………… 6

8.1 Cleaning Measures ………………………………………………………………………………………………… 6

8.2 Transportation and Storage …………………………………………………………………………………… 7

9. Service and Maintenance …………………………………………………………………………………………… 7

9.1 Disposal ………………………………………………………………………………………………………………… 7

9.2 After-sales Service ………………………………………………………………………………………………… 8

10.Contact us…………………………………………………………………………………………………………………… 8

Contents

E52 Series Piezo Controller User Manual

1.Security

1.1 Features

High power (50W)

Peak current (Higher than 17A)

Optional sensor closed loop module

Combination of active and passive heat dissipation

Over-temperature protection

1.2 Applicaitons

Piezo spot rubber valve

Piezo drives with large electrostatic capacity and requiring rapid response

1.3 Order information

E52.B1S-H—SGS sensor clsoed loop standard version ,1 channel piezo controller

E52.B1S-I—SGS sensor clsoed loop simplified version ,1 channel piezo controller

E52.A1K-H—Open loop, 1 channel piezo controller

Accept customized according to requirements：

① 12bit gain/-20 ～ 120V output voltage（standard version）

② 15bit gain/-20 ～ 150V output voltage

2. Driving Principle

3.Appearance

Front Panel Rear Panel

Side Inlet

Top Heat Dissipation Drawing

Side Outlet

E52 Series Piezo Controller User Manual

4. Frequency Load Curves

5.Interface

No. Functions Description

①Power indicator Green, lights when power's on

②Overcurrent

indicator

Red, lights when the output current exceeds the rated

value

③Analog input Analog voltage input interface

④Potentiometer Parameters adjustment(sensing zero, offset, gain)

⑤Sensor monitor Detect sensor output, voltage range 0~10V

⑥Sensor Sensor input

⑦PZT Voltage output interface

⑧Servo Open/closed loop switch

6.Power Calculation

● Average output（Sine wave operation mode）

Pa ≈ Upp • Us • f• Cpiezo

Pa=Average output[W]

Upp=Peak and peak drive voltage [V]

Us=Drive voltage[V]（（Vs+）-（Vs-））

Cpiezo=Piezo actuator capacitance[F]

f=Operating frequency of the sine wave[Hz]

E52 Series Piezo Controller User Manual

7. Notes and Suggestions

When the power used is large or the ambient temperature is high, external auxiliary

heat dissipation can be considered.

The temperature of the over-temperature power off protection is 75±5 ℃ , but this

function should be used as the protection against accidents under the limit condition. When

in normal use, please try to keep the top heat dissipation shell below 55℃ .

When the step amplitude is less than 3V, the peak current is small, less than 0.5A. As

the step amplitude increases, the peak current also increases.When the step amplitude is

greater than 10V, the peak current is greater than 17A.

When the output power is too large or the output is short circuited to the ground,

the overcurrent indicator will light up, and the power supply part will output with a smaller

cross-current.When the short circuit or power output is withdrawn, the overcurrent indicator

goes out and the power supply returns to normal. But do not overflow for a long time.

E52 cannot be used to drive inductive loads. If the inductive loads are driven, the

product may be damaged.

If there is no need, please do not twist the potentiometer easily.

8.1 Cleaning Measures

Note! The PCB board of the function module in the E52 is an ESD (electrostatic discharge)

sensitive device. Take precautions against any static build-up of these devices before use to avoid

contact with circuit component leads and PCB wiring. Before touching any electronic components,

the body rst touches the grounding conductor to discharge static electricity, ensuring that any

type of conductive particles (metal, dust or debris, pencil lead, screws) enter the device. Be

careful not to drop the equipment when cleaning, to avoid any form of mechanical shock!

Disconnect the power plug of the E52 system before cleaning.

Prevent cleaning fluid and any liquid from entering the system module to avoid short

8. Maintenance, Storage, Transportation

circuits.

The surface of the system chassis and the front panel of the module, please do not use an

organic solvent for surface wiping.

8.2 Transportation and Storage

This product is packed in carton. Transportation must be carried out under product

packaging conditions, and direct rain and snow, direct contact with corrosive gases and strong

vibrations should be avoided during transportation.

The instrument can be transported under various conditions of normal transportation, and

should avoid damp, load, collision, extrusion, irregular placement and other adverse conditions

during transportation.

If the instrument is not used for a long time, the instrument should be packaged and

stored.

The instrument should be stored in a non-corrosive atmosphere and in a well ventilated,

clean room.

In the process of transportation, storage and use, attention should be paid to fire

prevention, shockproof, waterproof and moisture proof.

Note: Pay attention to frost when the E52 series piezo controller is powered on in winter to avoid

burning the controller!

Check whether the controller has frost before power on (frost usually occurs when moving

from outdoor to indoor).

If the controller is frosted, wipe it or dry it and store it indoors for more than two hours

before powering it up for relevant operation.

9. Service and Maintenance

9.1 Disposal

When disposing of old equipment, please abide by the national regulations and local

regulations.Please dispose of the old equipment properly.Please contact CoreMorrow for

the upgrade and replacement of old equipment in order to meet the customer's handling of

system products.

E52 Series Piezo Controller User Manual

10.Contact us

Harbin Core Tomorrow Science & Technology Co., Ltd.

Tel: +86-451-86268790

Email: info@coremorrow.com

Website: www.coremorrow.com

Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China

CoreMorrow Official and CTO WeChat are below:

If you have an old device or an unusable device that cannot be handled, you can ship

it to the following address:

Address: 1F, Building I2, No.191 Xuefu Road, Nangang District, Harbin, Heilongjiang

9.2 After-sales Service

E52 does not contain user repairable components.

E52 must be returned to factory for any service and repair.

Any part of E52 is dismantled, there will be no warranty service.

E52 is a precision instrument which should be handled with care.

In case of any problem, please record the problem and contact CoreMorrow to be

repaired by professional technicians.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Coremorrow Controller Handbücher

Coremorrow

Coremorrow XE-650 Series Bedienungsanleitung

Coremorrow

Coremorrow E51.D7S Series Bedienungsanleitung

Coremorrow

Coremorrow E82.C256K Series Bedienungsanleitung

Coremorrow

Coremorrow E51.D12S Series Bedienungsanleitung

Coremorrow

Coremorrow E63.C1K Series Bedienungsanleitung

Coremorrow

Coremorrow E00/E01 series Bedienungsanleitung

Coremorrow

Coremorrow Modular E70 Series Bedienungsanleitung

Coremorrow

Coremorrow E81.A1K Series Bedienungsanleitung

Coremorrow

Coremorrow E80.D3S-K Series Bedienungsanleitung

Coremorrow

Coremorrow E70 Series Bedienungsanleitung

Coremorrow

Coremorrow E51.B3S Series Bedienungsanleitung

Coremorrow

Coremorrow E71.D4E-H Bedienungsanleitung

Coremorrow

Coremorrow E63.A1K Series Bedienungsanleitung

Coremorrow

Coremorrow H01 Bedienungsanleitung

Coremorrow

Coremorrow E53.C Series Bedienungsanleitung

Coremorrow

Coremorrow E53.B Series Bedienungsanleitung

Coremorrow

Coremorrow P87 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung