Cornelius ED22 Series Bedienungsanleitung

ED2XX Adapter Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ED22XX 629096792TE AND 629096795TE KITS

SAFETY

WARNING:

Before starting installation, read and understand all safety label and warnings on the machine. Also review and

understand all safety instructions in the owners, installation and service manuals.

Failure to comply could result in serious injury, death or damage to the equipment.

QUALIFIED SERVICE PERSONNEL

WARNING:

Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.

All wiring and plumbing must conform to national and local codes. Failure to comply could

result in serious injury, death or equipment damage.

SAFETY PRECAUTIONS

This unit has been specifically designed to provide protection against personal injury. To ensure continued

protection observe the following:

WARNING:

Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all

power is off to the unit before performing any work.

Failure to comply could result in serious injury, death or damage to the equipment.

CAUTION:

Always be sure to keep area around the unit clean and free of clutter. Failure to keep this area clean may result in

injury or equipment damage.

Revision Date: July 08, 2016 www.cornelius.com Revision: A

ED2XX Adapter Kit Installation Instructions

WARNING:

All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual

or the equipment manufacturer’s instructions.

Failure to comply could result in serious injury, death or damage to the equipment.

WARNING:

All of the attachment screws and plates must be installed as directed in this manual.

Failure to comply could result in serious injury, death or damage to the equipment.

1. Unpack the kit.

2. Place the insulation strip (item 12) over the studs on the baffle and insert the baffle assembly into the

adapter lid.

3. Place (2) sealing washers (item 9) over the studs and (2) flat washers (item 11), then fasten in place with

(2) plastic acorn nuts (item 8).

4. Set the ice maker lid on the top of the dispenser.

5. Using the slotted holes in the lid as a template, drill four (4) 0.140” diameter (9/64”) holes at the bottom of

the slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with

four (4) #8 sheet metal screws, two on each side.

6. Seal the Icemaker to the top of the dispenser as follows:

A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so

that the ice maker sets on the RTV.

Table 1. Loose-Shipped Parts

Item No. Part No. Name Qty.

620200136 Lid & Lanyard assembly - Grey

620200134 Lid & Lanyard assembly - Black

2. 15537 Lid Assembly 1

3. 29565 Bracket 2

4. 70217 #8 Screw 6

5. 50904 RTV 1

6. 90221 Label 1

7. 629096792TEINS Installation Instructions 1

8. 620701902 Acorn Nut, 8--32 Nylon 2

9. 620701901 Sealing Washer 2

10. 620037003 Baffle, Ice 1

11. 621701903 #8 Nylon Washer 2

12. 620505802 Insulation Strip 1

13. 630500109 Bin Stat 1

14. 43164 Screw MA 08-32 TRPH 10 SS 2

15. 70100 Nut HEX 08-32 SS Nylok 2

ED2XX Adapter Kit Installation Instructions

B. Set the ice maker onto the lid and position it as required.

C. Wipe away the excess RTV.

7. Drill 9/64” diameter holes into the ice maker cabinet using the bracket as a template. Use extreme care not

to drill into any Icemaker components (condenser, tubing, etc.). Secure the brackets using the screws

provided.

8. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in the

bottom of the ice maker. Wrap the eye of the wire form over the stud near the hole to the end of the wire

form bracket and wrap the tube around the end of the bracket several times, insuring the tube is secure.

NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from the

Icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.

9. If the plastic acorn nuts interfere with the positioning of the plastic manual fill cover, it may be necessary to

make small notches in the back of the cover to clear the acorn nuts.

10. The unit is now ready for operation.

Figure 1. ED2XX Kit

2 PLACES

ED2XX Adapter Kit Installation Instructions

Figure 2. ED2XX Kit

ICEMAKER

SEAL ICEMAKER TO

ITEM 2 WITH ITEM 5 (RTV)

DETAIL "A"

ENLARGED

DRILL 9/64 (.140) DIA.

HOLES USING BOTTOM

OF SLOTTED HOLES AS A

TEMPLATE.

(2) PLCS.

(6) PLCS.

VIEW "A"

ED2XX Adapter Kit Installation Instructions

Figure 3. Bin Stat

Figure 4. Detail X

FRONT PANEL OF ICE MAKER

REMOVED FOR CLARITY

SEE DETAIL X

IN FIGURE 4

BINSTAT COIL

NOT SUPPLIED

WITH BINSTAT

DETAIL X

SUPPORT

SCALE 0.580

NOTE: BINSTAT MUST BE WRAPPED AROUND SUPPORT AS SHOWN.

ED2XX Adapter Kit Installation Instructions

Figure 5. Reference Sheetmetal Cover Opening Dimensions for Mounting Icemaker.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cornelius Spender Handbücher

Cornelius

Cornelius The Profile PR150 BC Bedienungsanleitung

Cornelius

Cornelius NITROPRO MINI Bedienungsanleitung

Cornelius

Cornelius VIPER 3 FLAVOR Bedienungsanleitung

Cornelius

Cornelius QUEST ELITE 2 FLAVOR Bedienungsanleitung

Cornelius

Cornelius Millenium II 4000 Bedienungsanleitung

Cornelius

Cornelius Bubble Handbuch

Cornelius

Cornelius 2 Flavor Installationsanleitung

Cornelius

Cornelius pbd175 Bedienungsanleitung

Cornelius

Cornelius AquaCare Bedienungsanleitung

Cornelius

Cornelius CNB BIB Bedienungsanleitung

Cornelius

Cornelius IntelliBlue R134 Kuwait Series Bedienungsanleitung

Cornelius

Cornelius FlavorFusion Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Cornelius

Cornelius HELIX Bedienungsanleitung

Cornelius

Cornelius NITROPRO MINI Bedienungsanleitung

Cornelius

Cornelius VIPER Bedienungsanleitung

Cornelius

Cornelius IDC 255 PROGATE DRIVE THRU UNIT Bedienungsanleitung

Cornelius

Cornelius QUEST CAFE Einrichtungshandbuch

Cornelius

Cornelius Quest Elite 2000 Bedienungsanleitung

Cornelius

Cornelius Quest Bib Option Kit Bedienungsanleitung

Cornelius

Cornelius VANTAGE Bedienungsanleitung

Cornelius

Cornelius QUEST ELITE 4290 Bedienungsanleitung

Cornelius

Cornelius NITROPRO MINI Bedienungsanleitung

Cornelius

Cornelius Pro Fast Gate IDC255 Bedienungsanleitung

Beliebte Spender Handbücher anderer Marken

Silver King

Silver King Majestic SK12MAJ Kurzanleitung

Franke

Franke F3Dn Twin Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Bedienungsanleitung

DAN DRYER

DAN DRYER 282 Bedienungsanleitung

Essity

Essity Tork 473208 Bedienungsanleitung

CBS

CBS SD300BU-88 Einrichtungshandbuch

Sealey

Sealey MK77 Bedienungsanleitung

Fluid Management

Fluid Management Accutinter 1600 Bedienungsanleitung

Franke

Franke DVS SD99-010 Bedienungsanleitung

Graco

Graco Dispensit 1053-10C Fehlerbehebungshandbuch

ITALTINTO

ITALTINTO i50 Bedienungsanleitung

Coca-Cola

Coca-Cola FREESTYLE 9000 Bedienungsanleitung

Graco

Graco ProMix 2KE Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Bedienungsanleitung

Wayne

Wayne GLOBAL VISTA CNG Bedienungsanleitung

clarsen

clarsen H133 Bedienungsanleitung

PicoBrew

PicoBrew Zymatic Bedienungsanleitung

BOWMAN

BOWMAN BP-007 Bedienungsanleitung