CORNING Crimplok+ Connector 8700 APC SM 250/900 mm Bedienungsanleitung

P/N 78-0015-3873-1

Issue 2

Standard Recommended Procedure 78-0015-3873-1 | Issue 2 | September 2019 | Page 1 of 4

related literature | Search corning.com/opcomm. Click on “Resources/Standard Recommended Procedures.”

Crimplok™+ Connector 8700 APC SM 250/900 μm

Quick Reference Guide

SAFETY PRECAUTIONS

Protective Eyewear

CAUTION

Safety glasses should be worn when handling chemicals and cleaving the optical ber.

Chemical Precautions

CAUTION

Storage, use and disposal of isopropyl alcohol and methanolwater solution should be per your company health, safety and environmental

instructions. Refer to Safety Data Sheet (SDS) for health hazards, safe handling, proper use and control measures.

Bare Fiber Handling

CAUTION

Cleaved glass bers are sharp and can pierce the skin. Use tweezers when handling shards and dispose of them properly per your company health

and safety instructions.

Fiber Cable Handling

NOTICE

Optical ber can be damaged by excessive tensile, compressive and bending forces. Consult the manufacturer’s specications for proper handling

instructions.

Laser Safety

CAUTION

Take the proper precautions when working with optical ber because invisible laser light may be present. The principal laser hazard when working

with ber optics is injury to the eye. Never look directly into the end of a ber or connector using the naked eye, a view scope or a microscope when

connected to a laser source.

Standard Recommended Procedure 78-0015-3873-1 | Issue 2 | September 2019 | Page 2 of 4

1 2 3

4 5 6

7 8 9

10 11 12

Tool is set for 900 μm ber.

For 250 μm ber rotate ber

holder pad to the 250 mark. Insert Crimplok™+ Connector

Strip ber 40 mm

900 μm coating

edge, 24 mm

cleave length

250 μm coating

edge, 19 mm

cleave length

Optional– place

mark on buer at

edge of cleaver.

Insert ber

Ensure cap is still right justied

during insertion.

020 mm 40 mm

40 mm

IPA or

cleaner

Test ber to

ensure no

nick damage.

Ensure cap is aligned all the way to the right

╳

✓

Hold Crimplok+ connector

with thumb and rotate the

lever up to 90° and back

down to seat connector

and set cap to the right.

Standard Recommended Procedure 78-0015-3873-1 | Issue 2 | September 2019 | Page 3 of 4

13 14 15a

15b16 17

18 19 20

21 22 23

Check tension

Press rmly

Check for bow lift before

actuation arm is vertical

Apply and center lapping lm to

orange pad.

Spray distilled water

2X on lapping lm

Push down

until it clicks

Push button

Turn until

stop

Need to

re-clean

Thread caught,

re-clean with

a twist

Remove Crimplok+

connector & clean

1. Dry o water

2. Clean with alcohol

or cleaner

3. Dry o & twist

Top image activated, bottom image

not activated

Remove Crimplok™+ Connector

from tool

Buer mark will move left

during bow lift

╳

✓

Standard Recommended Procedure 78-0015-3873-1 | Issue 2 | September 2019 | Page 4 of 4

Corning Optical Communications LLC • 4200 Corning Place • Charlotte, NC 28216 USA

800-743-2675 • FAX: 828-325-5060 • International: +1-828-901-5000 • www.corning.com/opcomm

Corning Optical Communications reserves the right to improve, enhance, and modify the features and specications of Corning Optical Communications products without

prior notication. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are

Caution reminder: Never look directly

into the end of a fiber or connector

when connected to a laser light source

using the naked eye or a microscope.

╳

✓✓

Ideal clean ber end face

Thin black line is visible

Light grey Dark grey

No line, just grey to white

Chips or cracks inside the ½ diameter circle are not allowed.

Fiber is missing, strip,

go to step 3

Acceptable chip

Inhaltsverzeichnis

Andere CORNING Kabel und Steckverbinder Handbücher

CORNING

CORNING X75 8000 Series Bedienungsanleitung

CORNING

CORNING Gold 000301T4180002M Bedienungsanleitung

CORNING

CORNING SRP-004-067 Bedienungsanleitung

CORNING

CORNING PCH-02U Bedienungsanleitung

CORNING

CORNING EDGE-01U-SP Bedienungsanleitung

CORNING

CORNING ECL-C4U Bedienungsanleitung

CORNING

CORNING Lanscape Solutions CLSSC-03U Bedienungsanleitung

CORNING

CORNING ClearCurve SRP-005-065 Bedienungsanleitung

CORNING

CORNING Evolant TKT-OPTISNAP-Cx Bedienungsanleitung

CORNING

CORNING UCNCP 5 MFT Flip HS Series Bedienungsanleitung

CORNING

CORNING SST Bedienungsanleitung

CORNING

CORNING UCNCP 5 MFT Flip HS Series Bedienungsanleitung

CORNING

CORNING EDGE Splice Cassette Bedienungsanleitung

CORNING

CORNING SST-Drop Bedienungsanleitung

CORNING

CORNING UniCam SRP-006-150 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung