Craftex CT023N Bedienungsanleitung

CT023N, CT019N, CT028N, CT022N, CT026N

DRILL PRESSES

OWNER’S MANUAL

13” 14”

13” 14” 20”

TABLE OF CONTENTS

GENERAL SAFETY INSTRUCTIONS PAGE3

SPECIFIC SAFETY INSTRUCTIONS PAGE 4

Features PAGE 5

Electrical Information PAGE 6

Unpacking & Cleaning PAGE 7

Assembly

BasetoColumn PAGE8

TabletoColumn PAGE8

Drill Press Head to Column PAGE 9

Feed Handle PAGE 9

PulleyCover PAGE10

Arbor and Chuck PAGE 10

Removing the Chuck PAGE 10

Mounting the Drill Press PAGE 10

Adjustments

Changing Spindle Speeds PAGE 11

Table Adjustments PAGE 11

Drilling Depth PAGE 12

Spindle Return Spring PAGE 12

Operation

Drilling Speeds PAGE 13

Metalworking PAGE13

Woodworking PAGE 13

Feeding PAGE 13

Laser Operation PAGE 14

Maintenance PAGE 15

Schematic Diagram for CT019N, CT022N & CT026N PAGE 16

PartsList PAGE17

Schematic Diagram for CT023N & CT028N PAGE 19

PartsList PAGE20

Warranty PAGE22

GENERAL SAFETY INSTRUCTIONS

EXTREME CAUTION SHOULD BE USED IN OPERATING ALL POWER TOOLS. KNOW

YOUR POWER TOOL, BE FAMILIAR WITH ITS OPERATION. READ THE OWNER’S

MANUAL AND PRACTICE SAFE USAGE PROCEDURES AT ALL TIMES.

CONNECT your machine ONLY to the matched and specified power

source.

WEAR SAFETY GLASSES, HEARING PROTECTION and SAFETY

SHOES when operating heavy machinery. Always wear safety glasses.

DO NOT wear loose clothing or jewellery when operating machinery.

A Safe Environment is important. Keep the area free of dust, dirt and

other debris in the immediate vicinity of the machine.

BE ALERT! Do Not Use prescription or other drugs that may affect your

ability or judgement to safely use this machine.

DISCONNECT the power source when making other adjustments or repairs.

NEVER leave an operating tool unattended.

NEVER reach over the table when the tool is in operation.

ALWAYS keep blades, knives or bits sharp and properly aligned.

ALWAYS keep all safety guards in place and ensure their proper function.

ALWAYS make sure that any tools used for adjustments are removed

before operating the machine.

ALWAYS secure your work with the appropriate clamps or vises.

ALWAYS keep bystanders safely away while operating machinery.

THINK SAFETY. WORK SAFELY. Never attempt a procedure if it does not

feel safe or comfortable.

SPECIFIC SAFETY INSTRUCTIONS

Always make certain that you clamp down any object that you are drilling

into.

When drilling, make sure that you are using the correct speed for the

material being drilled.

Clear the drill press table of all objects before turning the tool on.

Keep hands and fingers safely away from the spinning drill bits.

NEVER start the drill press with the drill bit in contact with the work-piece.

Make certain that the drill bit is securely tightened into the drill chuck.

NEVER wear gloves while operating a drill press.

Make certain that the table lock is securely tightened before using the drill

press.

Never attempt to drill any material that is not flat without using a secure jig

for that specific work-piece.

Always remove the drill bit before leaving the machine.

DRILL PRESS FEATURES

As part of the growing line of Craftex woodworking equipment, we are proud to

offer the CT023N, CT019N, CT028N, CT022N, CT026N Drill Presses. The

Craftex name guarantees Craft Excellence. By following the instructions and

procedures laid out in this owner’s manual, you will receive years of excellent

service and satisfaction. The CT023N, CT019N, CT028N, CT022N, CT026N are

professional tools and like all power tools, proper care and safety procedures

should be adhered to.

CT023N

Size: 13"

Motor: 1/2 HP

Chuck: 5/8"

Spindle: MT2

Table: 10" SQ.

Speeds: 12

Height: 38"

Weight: 57 kg.

Carton size: 19" x

10" x 30"

CT019N

Size: 14"

Motor: 3/4 HP

Chuck: 5/8"

Spindle: MT2

Table: 11 1/4" SQ.

Speeds: 12

Height: 38"

Weight: 73 kg.

Carton size: 20" x 9"

x 32"

CT028N

Size: 13"

Motor: 1/2 HP

Chuck: 5/8"

Spindle: MT2

Table: 10" SQ.

Speeds: 12

Height: 62"

Weight: 66 kg.

Carton size: 20" x 10"

x 56"

CT022N

Size: 14"

Motor: 3/4 HP

Chuck: 5/8"

Spindle: MT2

Table: 11 1/4" SQ.

Speeds: 12

Height: 64"

Weight: 86 kg.

Carton size: 20" x 10" x

56"

CT026N

Size: 20"

Motor: 1 1/2 HP

Chuck: 5/8"

Spindle: MT4

Table: 18 3/4" x 16 3/4"

Speeds: 12

Height: 67"

Weight: 148 kg.

Carton size: 29" x 13" x

56"

These 5 presses feature Rack & Pinion raising mechanism that gives smooth and accurate

movement of the drill press. The full cast iron table tilt, allowing for a variety of drilled holes.

The operational handles are all made of solid cast iron and feature comfort rubber grip pads

for ease of use.

Each of these drill presses also feature built in laser guiding technology. This can come in

handy when doing single cuts, but more so when repetitive cuts are in order. See page 14 for

more details.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides the path of least

resistance for electrical current and reduces the risk of electrical shock. This tool

is equipped with an electrical cord that has an equipment grounding conductor

and a grounding plug. The plug MUST be plugged into a matching outlet that has

been properly installed and grounded in accordance with ALL local codes and

ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If the provided plug will not fit the

electrical outlet, have the proper outlet installed by a qualified licensed

electrician.

IMPROPER CONNECTION of the equipment grounding conductor can result in

risk of electrical shock. The conductor wire with the green insulation (with or

without yellow stripes) is the equipment-grounding conductor. If repair or

replacement of the electrical cord or plug is required, DO NOT connect the

equipment grounding conductor to a live terminal.

If in doubt about these instructions consult a qualified,

licensed electrician.

USE ONLY A THREE-WIRE EXTENSION CORD with

a 3-prong grounding plug and three-hole receptacles

that accept the tool’s plugs as shown.

It is recommended that stationary tools be assigned to a dedicated 15 amp circuit

using #12 wire.

UNPACKING AND CLEANING

Carefully unpack your drill press and all of its parts. Compare the carton contents

with the illustration below. Do not discard any packing material until the drill press

is completely assembled and operating properly.

Your drill press and some of its parts have been coated with a protective

lubricant that should be removed before the machine is assembled. This can be

done with a soft cloth moistened with non-corrosive kerosene or mineral spirits.

ASSEMBLY

BASE TO COLUMN

Select the base and the drill press column from the

loose parts. Select the four 10mm x 25mm bolts

from the parts bag. Align the holes of the post flange

to the threaded holes in the base. Insert the bolts

and tighten securely.

TABLE TO COLUMN

Remove the ring (3) by loosening the set-screw (4).

Remove the rack (5) from the column.

Check that the worm gear (8) is properly seated

inside the table bracket (7) and it comes in contact

with the gears. The handle shaft (9) should extend

out of the housing by about 1”.

Insert the rack (5) into the geared groove (6) of the

table bracket (7). The table bracket should sit at the

center section of the rack.

Slip the table bracket and rack (1) carefully onto the

column (2). Insert the bottom of the rack into the slot

(3) at the base of the column.

Hold the bracket and rack against the column and

slip the rack ring (4) onto the column.

The rack (1) fits under the rack ring (4). Make sure

there is enough clearance between the rack and the

ring to allow the table to rotate around the column.

Tighten the set-screw (5) to hold the ring in position.

ASSEMBLY

Attach the elevation handle by tightening the set-screw (2)

Thread the column lock into the table bracket (1).

Rotate the table and position it directly over and in line with

the base.

DRILL PRESS HEAD TO COLUMN.

Lift the drill press head carefully and position it above the

column. NOTE: this may require the help of a second

person.

The column fits into the drill press mounting hole. Make

certain the mounting hole is properly seated on the column.

Line the drill press head up with the table and base and then

tighten the two set-screws using the supplied hex wrench.

FEED HANDLE.

Fit the one-piece cast-iron feed handle onto the shaft.

ASSEMBLY

PULLEY COVER

Insert washer and screw through the hole in the

pulley cover, thread the knob onto the screw and then

tighten.

INSTALLING THE ARBOR AND CHUCK

Slide the long end of the arbor (1) into the spindle (2)

as far as it will go.

Slide the chuck (3) onto the arbor and then place a

block of wood under the chuck and tap the chuck and

arbor with a hammer until it seats into the spindle.

DO NOT STRIKE THE CHUCK DIRECTLY WITH A

STEEL HAMMER.

REMOVING THE CHUCK

Lower the chuck to its lowest position exposing the

spindle sleeve (1).

The spindle sleeve has a large oval hole (2) on both

sides of it.

Rotate the chuck (3) until the spindle hole (4) lines up

with the hole in the spindle sleeve.

Insert the wedge (5) and tap the wedge lightly with a

hammer.

The arbor and the chuck will release from the spindle.

MOUNTING THE DRILL PRESS

Your drill press must be securely fastened to the floor

to prevent the machine from tipping, sliding or walking

during operation. There are two base holes provided

for this.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftex Elektrowerkzeuge Handbücher

Craftex

Craftex CT114 Bedienungsanleitung

Craftex

Craftex CX614 Bedienungsanleitung

Craftex

Craftex CX12HC Bedienungsanleitung

Craftex

Craftex CS Series Bedienungsanleitung

Craftex

Craftex CT087 Bedienungsanleitung

Craftex

Craftex CX08HC Bedienungsanleitung

Craftex

Craftex CX06SC Bedienungsanleitung

Craftex

Craftex CT180 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CT188 Bedienungsanleitung

Craftex

Craftex CX902 Bedienungsanleitung

Craftex

Craftex CT133 Bedienungsanleitung

Craftex

Craftex CT201 Bedienungsanleitung

Craftex

Craftex CT024N Bedienungsanleitung

Craftex

Craftex CX817N Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CT056 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CT106 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CX617 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung