Craftmade WCS-100 Bedienungsanleitung
WCS-100 Smart
on/off Switch
Installation Guide
WARNING:
RISK OF ELECTRIC SHOCK
This product installation requires
handling 120 volt wiring.
Follow each step carefully.
If any concerns handling wiring,
hire a qualied electrician.
Ensure all work meets local and
federal regulations.
• Install your Craftmade Smart Switch.
• Download the Craftmade Smart app.
• Add your Craftmade Smart Switch
the Craftmade Smart app.
Simple DIY Setup
WARNING:
RISK OF ELECTRIC SHOCK
• Rating 120V AC 60Hz.
• Neutral wire required (wire is usually white or gray).
• Ground wire required (wire is usually green,
green with yellow stripe, or bare copper).
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with compatible LED bulbs.
• LED up to 150 watts.
• Incandescent/Halogen up to 600 watts.
Compatibility Requirements Parts Included
• Rating 120V AC 60Hz.
• Neutral wire required (wire is usually white or gray).
• Ground wire required (wire is usually green,
green with yellow stripe, or bare copper).
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with compatible LED bulbs.
• LED up to 150 watts.
• Incandescent/Halogen up to 600 watts.
• Rating 120V AC 60Hz.
• Neutral wire required (wire is usually white or gray).
• Ground wire required (wire is usually green,
green with yellow stripe, or bare copper).
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with compatible LED bulbs.
• LED up to 150 watts.
• Incandescent/Halogen up to 600 watts.
Compatibility Requirements
Switch Wall Plate
Wire Labels
Line GroundLoad Neutral
4 Wire Nuts 4 Mounting
Screws
Parts Included
• Rating 120V AC 60Hz.
• Neutral wire required (wire is usually white or gray).
• Ground wire required (wire is usually green,
green with yellow stripe, or bare copper).
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with compatible LED bulbs.
• LED up to 150 watts.
• Incandescent/Halogen up to 600 watts.
Tools you will need
Philips Screwdriver
Needle Nose Pliers
(Recommended)
Voltage Tester
(Recommended)
Allow 30 minutes to perform installation.
Step 1 - Turn off the Power!
• Turn off the power for the switch location
at the circuit breaker box.
• Test existing switch by toggling switch on/off,
ensuring the lights do not turn on.
• Now, follow these setup steps
for a single gang switch.
Tools you will need
Step 2 - Remove your old switch
1. Remove the existing wall plate
and switch from the wall.
2. Use voltage tester on the black wire to conrm
power to the switch is off (recommended)
3. Before disconnecting the wires from the wall,
label each with the provided wire labels.
a. Attention: Neutral and ground wires are
required. If you don’t have either wire, the
Craftmade Smart Switch cannot be installed.
4. Disconnect wires and remove the existing switch.
Step 2 - Remove your old switch
1. Remove the existing wall plate
and switch from the wall.
2. Use voltage tester on the black wire to conrm
power to the switch is off (recommended)
3. Before disconnecting the wires from the wall,
label each with the provided wire labels.
a. Attention: Neutral and ground wires are
required. If you don’t have either wire, the
Craftmade Smart Switch cannot be installed.
4. Disconnect wires and remove the existing switch.
Step 2 - Remove your old switch
Step 3 - Connect the Wires
1. Connect the neutral (white) wire on the switch
to neutral (white label) wire from the wall.
2. Connect the line (black) wire on the switch to
the line (black label) wire from the wall.
3. Connect the load (black) wire on the switch to
the load (red label) wire from the wall.
4. Connect the ground (green) on the switch to
the ground (green label) wire from the wall.
Inhaltsverzeichnis
Andere Craftmade Schalten Handbücher
