Craftsman 200.57933 Bedienungsanleitung

Owner’s Manual/Manual Del Propietario

Read and follow all safety rules and operating

instructions before first use of this product.

Fasten the manual near the garage door after

installation.

Periodic checks of the opener are required to

ensure safe operation.

DO NOT install on a one-piece door.

SEOMU01A-1

Write down the Craftsman®serial number located on the garage door opener:

Anote en el recuadro el número de seria de Craftsman ubicado en el abre-puerta:

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A

www.craftsman.com

Leer y seguir todas las reglas de seguridad y

las instrucciones de operación antes de usar

este producto por primera vez.

Guardar este manual cerca de la puerta de la

cochera.

Se deben realizar revisiones periódicas del

abridor de puertas para asegurar su

operación segura.

Los dispositivos y funciones automáticas

deben usarse ÚNICAMENTE con puertas

seccionales.

Spanish Section Begins Page: 29

Manual en Español empieza en la pagina: 29

For Residential Use Only

Sólo para uso residencial

GARAGE DOOR OPENER

Abridor de puerta de cochera

MODEL/MODELO 200.57933

Table of Contents

Courtesy light turns on/flashes with audible ‘click’.

(If light bulb is not installed, ‘click’ represents the light)

DO NOT connect power Please connect power

Introduction

Symbols and Icons 2

Inventory 3

Preparation / Tools Required 4

Assembly

Rail and Trolley Assembly 5

Installing the Cable and Chain 6

Important Installation Instructions 7

Mounting Header Bracket 8

Installation

Attaching Rail to Header Bracket and Mounting Door Bracket 9

Mounting Opener to Ceiling 10

Attaching Door Arms 11

Installing Light and Emergency Release Handle 12

Wiring

Wiring Instructions 13

Connecting Photo Eye Safety System 14

Connecting Push Button 15

ConnectingPower 16

Adjustment

Aligning the Photo Eye Safety System 16

Travel Limit Adjustment 17

Force Adjustment 18

Final Adjustment and Testing 19

Operation

Programming 1 Button Remote 20

Programming Keyless Entry Pad* 21

Important Safety Instructions 22

Operating the Opener 23-24

Maintenance 25

Troubleshooting 25

Repair Parts and Service

Rail Assembly Parts / Installation Parts / Accessories 26

Opener Assembly parts 27

Warranty 28

Symbols and Icons

! WARNING READ WARNINGS CAREFULLY to prevent SERIOUS INJURY or DEATH caused by

electrocution or mechanical hazard.

Installation hardware

*See Accessories in Repair Parts section of this manual for purchase information.

— Door arms / Mounting Opener

Inventory

x 2

Clevis Pin — Pulley

3/8” x 1-3/4”

Hitch Pin — Locking Clevis Pins

x 4

Lag Screw #12 x 1”— Photo Eye System

Lag Screw 5/16” x 1-1/2”

— Header Bracket / Mounting Opener

Bolt 5/16” x 1”

Drywall Anchor

- Push Button

x 2

Screw #6 x 1-1/4”

- Push Button

x 30

5/16” Flange Nut

x 4 x 4

x 4

x 1

Emergency Release Handle + Rope

Literature + Safety Labels

Chain

Photo Eye Safety System

Opener Unit + Light Lens Cover

Sprocket Cover

Header

Bracket

Door Bracket

Trolley

Door Arms

Pulley

Rail — Header Segment

Rail — Middle Segments x3

INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE)

Hanging

Brackets

Insulated Staples

— Securing wires

x 2

Self-Threading Screw 1/4” x 5/8”

Door Bracket

Trolley Shaft

and Cable

Master Link Set

—Trolley Shaft

x 1

Rail — End Segment with Trolley Stop Bolt

Clevis Pin — Door arms

5/16” x 1”

Clevis Pin — Header Bracket

5/16” x 1-1/2”

1-Button

Remote Push Button

OPTIONAL

3-Button Mini

Remote*

Wireless Keyless Entry Keypad*

Drywall Anchor

x 2

Screw #6 x 1”

OPTIONAL

*See Accessories in Repair Parts section of this manual for purchase information.

Preparation

Level

Tape Measure

Hack Saw

Pencil

Drill, 3/16” and 5/16” Drill Bits

Tools Required

Step Ladder

Screwdriver

Hammer

Sectional Garage Door BEFORE beginning Installation:

1. Disable locks and remove all ropes connected to the

garage door.

2. Perform the following door test to ensure your door is

balanced and in good working condition.

To Test Your Garage Door

1. Raise and lower the door to check if there is any sticking or

binding.

2. Check for loose hinges, damaged rollers, frayed cables and

damaged or broken springs.

3. Lift the door approximately halfway and release. The door

should stay at the point under proper spring tension.

Call a qualified garage door service technician if your door binds,

sticks or is unbalanced.

! WARNING

To prevent SERIOUS INJURY or DEATH:

- Before beginning installation of the opener please complete the following test to ensure that your door is

balanced and in good working condition.

- A poorly balanced door can cause serious injury and damage to the opener.

- Always have a qualified garage door service technician make any required adjustments and/or repairs to

your door before proceeding with installation.

- DISABLE ALL LOCKS and REMOVE ALL ROPES connected to the garage door BEFORE installing

and/or operating the opener.

To prevent damage to the door and opener:

- DO NOT connect power until instructed.

- Operate this opener with AC 120V/60Hz power supply ONLY.

Pliers

Adjustable Wrench Ratchet with

5/16”, 7/16” and 1/2” sockets

DO NOT REUSE PARTS FROM ANOTHER BRAND OF OPENER!!!

Rail and Trolley Assembly

Opener

Trolley direction (Top View)

Clevis Pin

Pulley

Hitch Pin

Clevis Pin — 3/8” x 1-3/4”

Hitch Pin

Connect shaft to Trolley with “click”

To Assemble Rail and Opener

1. Prepare the rails as shown in Fig.1.

2. Connect the rails starting with the header segment. Insert

the tapered ends into open ends, apply any additional force

necessary by tapping the rail on padded flooring. Ensure

the end segment has trolley stop bolt facing up. Make sure

the rails are securely joined together as shown.

3. Slide the trolley onto the rail from the header segment.

Make sure the arrow is pointing towards the door as shown

in Fig.1.

4. Connect the rail assembly to the rail bracket on the opener.

To Assemble the Header Section of Rail

Follow steps shown in Fig.2:

1. Remove the “trolley shaft and cable” from the chain carton

and lay it beside the rail assembly. Hold cable eyelet on the

end of cable and thread about 20” (50cm) through the slot

on the Header Segment of the rail.

2. Insert the pulley into the opening while the cable is hanging.

3. Secure the pulley by inserting the 3/8” x 1-3/4” clevis pin

through the top of the rail.

4. Lock the clevis pin with a hitch pin. Rotate the pulley to

ensure it spins smoothly.

Refer to Fig.3 to connect the trolley shaft to the trolley. Slide both

the trolley shaft and trolley towards each other. A “click” will be

heard when they are connected.

To Link Cable with Chain

Refer to Fig.4. Place the chain carton beside the rail, hold the

“chain to cable connector” and pull about 8” (20cm) of chain from

the box. Thread the chain to cable connector onto the trolley

shaft so that they are loosely linked together.

Fig.1

Fig.2

Fig.4

Fig.3

! CAUTION

- DO NOT connect power until instructed.

- To prevent INJURY, keep hands and fingers

away from joints and possible sharp edges.

- Wear gloves when installing chain and cable.

Rail Bracket

Trolley Shaft

Trolley Shaft Trolley

Cable Eyelet

Loosely link together

Trolley Shaft Chain-to-Cable Connector

Chain

When connecting the rails ensure they are securely connected as shown above.

To apply additional force tap gently on the end of the rail with a rubber mallet*.

*Only use a soft rubber mallet to tap on the end of the rails as other tools may damage your rail.

Rail — Header Segment

Rail — Middle Segments

(tapered) x 3

Rail — End Segment (tapered)

with Trolley Stop Bolt

DOOR

If the supplied chain and rails are not long enough for your installation, you may purchase an 8-foot or 10-foot Chain Drive

Extension Kit. To purchase a kit, visit a Craftsman outlet ,call 1-888-331-4569,or go online to www.craftsman.com

To Install Chain

1. Pull the remaining chain along the rail toward the opener.

2. A segment of chain marked in RED will be seen. Place this

segment in the approximate location on the sprocket as

shown in Fig.1.

3. When the chain is aligned properly around the sprocket, pull

the chain-to-cable connector towards the trolley shaft.

Follow steps shown in Fig.2 to connect & tighten the chain:

1. Align the open end of the chain to the cable eyelet and

connect together using the master link set.

2. Turn the chain-to-cable connector on the trolley shaft until

the chain is about 1/4” (6mm) above the base of the rail.

Compare with the illustration below.

3. Tighten the flange nut on trolley shaft against the chain-to-

cable connector.

When the chain and cable are tightened around the rail and

sprocket on the opener, check and make sure the chain is

properly aligned and not twisted. Attach the sprocket cover to the

opener as shown in Fig.3.

Notice

During operation, it is normal for the chain to appear loose when

the door is closed. If the chain returns to the position as shown

below when the door is opened, the chain is adjusted properly.

DO NOT re-tighten the chain.

When performing maintenance, always PULL the emergency

release to DISCONNECT the door from opener before adjusting

the chain.

Installing Cable and Chain

! WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers clear from sprocket during operation.

- Wear gloves when installing chain and cable.

- Keep hands and fingers away from joints and possible sharp edges.

Cable

Chain

Fig.1

Fig.2 Fig.3

Sprocket

Cover

Tighten until... 1/4” (6mm)

Base of Rail

Mid-point of rail assembly

Tighten nut

Flange Nut

Master Link

Link Cap

Spring Clip

Cable Eyelet

Open end of chain

Chain to Cable Connector

To Connect and Tighten the Chain:

Sprocket

Rail Bracket

Chain

Top of Rail

Chain in RED

Actual Size

Hitch Pin

Clevis Pin

To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Install only on a properly balanced garage door. An improperly balanced door has the potential to inflict severe

injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before

installing the opener.

3. Remove all ropes and remove or make inoperative all locks connected to the garage door before installing

opener.

4. Where possible, install the door opener 7 feet or more above the floor. For products having an emergency

release, mount the emergency release within reach, but at least 6 feet above the floor and avoiding contact

with vehicles to avoid accidental release.

5. Do not connect the opener to source of power until instructed to do so.

6. Locate the push button: (a) within sight of door, (b) at a minimum height of 5 feet so small children are not able

to reach it, and (c) away from all moving parts of the door.

7. Install the Entrapment Warning Label next to the wall-mount push button in a prominent location. In case the

adhesive does not adhere on the surface, the label should be attached to the surface by mechanical means.

8. After installing the opener, the door must reverse when it contacts a 1-1/2-inch high object (or a 2 by 4 board

laid flat) on the floor.

Important Installation Instructions

Place entrapment warning label on wall next to garage door control.

! WARNING

IMPORTANT INSTALLATION INSTRUCTIONS

To Install Header Bracket

Note: Installation procedures may vary according to door

type.

1. While inside your garage, close the door and mark the

vertical centerline of the garage door. Extend the line onto

the header wall above the door spring.

2. Open the door to the highest point of travel. Mark a line on

the header wall 2“ (5cm) above the highest point of travel.

Note: DO NOT install the header bracket over drywall. In some

installations, it may be necessary to install a 2x4 across two wall

studs to create a suitable location for the header bracket.

If installing into masonry, use concrete anchors (not provided).

Wall-Mounting

As shown in Fig.2, place the header bracket on the vertical

centerline in direction shown.

Mark and drill two 3/16” holes. Fasten the header bracket

securely to a structural support using two 5/16” x 1-1/2” lag

screws.

Alternative Ceiling-Mounting

Ceiling-mounting is suggested ONLY when clearance is minimal.

Extend the vertical centerline onto the ceiling as shown in Fig.3.

Center the header bracket on the vertical mark, no more than

6” (15cm) from the header wall. Mark and drill holes to fasten the

header bracket securely to a structural support.

Mounting Header Bracket

OPENER

MAX. 6” (15cm)

Vertical Centerline Lag Screw

5/16” x 1-1/2”

! WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- The header bracket MUST be SECURELY fastened to the structural support on the mounting wall or

ceiling, otherwise the door may not reverse when required. DO NOT install the header bracket over drywall.

- Concrete anchors MUST be used when mounting the header bracket into masonry.

- NEVER try to loosen, move or adjust garage door springs, cables, pulleys, brackets, or hardware.

- Contact a qualified garage door service technician if your door binds, sticks or is unbalanced. An unbal-

anced door might not reverse when required.

Vertical Centerline

Fig.2 (Wall-Mounting) Fig.3 (Ceiling-Mounting)

7ft door

8ft max

8ft door

9ft max

Fig.1

Ceiling

Header Bracket

Header Wall

2” (5cm) clearance

Door Track

Door

Highest Point of Door Travel

Support block on floor

Door Spring

* VERY IMPORTANT! *

Max recommended rail height from floor

 7ft door = 8ft max height

 8ft door = 9ft max height

MAX RAIL HEIGHT

Floor

Attaching Rail to Header Bracket and Mounting Door Bracket

! CAUTION

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- REINFORCEMENT is recommended for fiberglass, aluminum or lightweight steel garage doors BEFORE

installing the door bracket. Contact your door manufacturer for reinforcement options.

Fig.1

Fig.2 Fig.3

Carton

Clevis Pin - 5/16” x 1-1/2”

Hitch Pin

Self-Threading

Screw - 1/4” x 5/8”

Vertical Centerline of Door

(a) (b) (c)

2-4” (5-10cm)

To Attach the Opener to the Header Bracket

1. As shown in Fig.1, use the packaging carton as temporary

support for the opener. Place the opener on carton to

prevent damage.

2. Align the mounting hole on the header rail to the mounting

hole on the Header Bracket.

3. Connect the header rail and the door bracket together with

a 5/16” x 1-1/2” clevis pin and lock it in place with a hitch

pin.

To mount the Door Bracket

Note: Some door reinforcement kits may provide direct

attachment of the door arm to the reinforcement bracket. If you

have a door reinforcement bracket with this option, skip this step

and proceed with the next step “mounting opener to ceiling”.

1. Position the door bracket on the centerline of the door

approximately 2” - 4” (5-10cm) below the top edge of the

door, as shown in Fig.2.

2. Depending on the construction of your door, install using

one of the steps shown if Fig. 3 below:

For steel / lightweight doors with vertical steel

reinforcements / factory reinforced.

(a) Mark and drill two 3/16” holes. Make sure not to drill

through the garage door. Secure the door bracket with two

1/4” x 5/8” self-threading screws (provided) as shown in

Fig.3(a).

(b) Alternative installation: Drill two 5/16” holes through the

door. Secure the door bracket using two 5/16” bolts, lock

washers and nuts (not provided) as shown in Fig.3(b). The

length of bolts will depend on the thickness of your door.

Wood door

Secure the door bracket using two 5/16” carriage bolts,

washers and nuts (not provided) as shown in Fig.3(c). The

length of bolts will depend on the thickness of your door.

Note: DO NOT use Self-Threading Screws on a wood door.

To Mount the Opener to Ceiling

The three most common installation options are shown in

Fig.1-3.

Fig.1 shows mounting the opener directly to structural

support on the ceiling. Fig.2 and 3 show mounting on a

finished ceiling, with heavy duty angle iron*.

*(angle iron not included)

Determine the mounting option that works best for your

application and follow installation steps below:

1. Raise the opener and rail assembly and temporarily place it

on a stepladder.

2. Position the opener and rail assembly so that it is aligned to

the center line of the garage door. If the header bracket was

mounted off center, align the opener with the header

bracket.

3. Measure the distance from each side of the opener to the

structural supports.

4. Cut both hanging brackets to appropriate length.

5. Drill 3/16” holes in the structural supports.

6. Secure one end of each of the hanging brackets to the

structural supports using 5/16” x1-1/2” lag screws

(provided).

7. Secure the opener to the hanging brackets and secure each

side with a 5/16” x 1” bolt and flange nut (provided).

8. Move the door manually to check clearance between

highest point of travel of the door and rail. If the door hits the

rail, raise the header bracket or adjust the mounting of

opener.

9. Remove the ladder ONLY when the opener is securely

Mounting Opener to Ceiling

! WARNING

To prevent SERIOUS INJURY or DEATH:

- DO NOT connect power until instructed.

- Install the opener at least 7 feet (2.13m) above the floor.

- Fasten the opener SECURELY to STRUCTURAL SUPPORTS of the garage to prevent falling.

- If installing brackets to masonry, concrete anchors (not provided) MUST be used.

Fig.1

Fig.2

Fig.3

Lag Screw 5/16” x 1-1/2”

Bolt 5/16” x 1”

Flange Nut

Finished ceiling

Fastening Hanging Brackets to structural supports

Securing Opener to Hanging Brackets

Bolt / Lock Washer / Nut

not provided

Bolt / Lock Washer / Nut

not provided

Angle Iron not provided

Andere Handbücher für 200.57933

Inhaltsverzeichnis

Andere Craftsman Garagentoröffner Handbücher

Craftsman

Craftsman 139.53991 Bedienungsanleitung

Craftsman

Craftsman 139.53661SRT3 Bedienungsanleitung

Craftsman

Craftsman 139.18451DM Bedienungsanleitung

Craftsman

Craftsman 139.53965SRT Bedienungsanleitung

Craftsman

Craftsman 139.5391 Bedienungsanleitung

Craftsman

Craftsman 139.53664SRT Bedienungsanleitung

Craftsman

Craftsman 139.53990DS Bedienungsanleitung

Craftsman

Craftsman 139.53696EV Bedienungsanleitung

Craftsman

Craftsman 139.53664SRT2 Bedienungsanleitung

Craftsman

Craftsman 139.653100 Bedienungsanleitung

Craftsman

Craftsman 139.53800SRT Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Craftsman

Craftsman 139.53914D Bedienungsanleitung

Craftsman

Craftsman 139.53954 Bedienungsanleitung

Craftsman

Craftsman 139.53915D Bedienungsanleitung

Craftsman

Craftsman 139.53919 Bedienungsanleitung

Craftsman

Craftsman 139.53930D Bedienungsanleitung

Craftsman

Craftsman 139.53335SRT3 Bedienungsanleitung

Craftsman

Craftsman 139.53661SRT1 Bedienungsanleitung

Craftsman

Craftsman 139.10158 Bedienungsanleitung

Craftsman

Craftsman 139.53920DM Bedienungsanleitung

Craftsman

Craftsman 139.53902D Bedienungsanleitung

Craftsman

Craftsman 139.18616SR Bedienungsanleitung

Craftsman

Craftsman 139.53990DS Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung