Craftsman 200.57983 Bedienungsanleitung

SEOMU06A-1

Table of Contents

Introduction

Symbols and Icons 2

Inventory 3

Preparation / Tools Required 4

Assembly

Rail and Trolley Assembly 5

Installing the Belt 6-7

Important Installation Instructions 8

Mounting Header Bracket 9

Installation

Attaching Rail to Header Bracket and Mounting Door Bracket 10

Mounting Opener to Ceiling 11

Attaching Door Arms 12

Installing Light and Emergency Release Handle 13

Wiring

Wiring Instructions 14

Connecting Photo Eye Safety System 15

Connecting Door Control Console 16

Connecting Power 17

Adjustment

Aligning the Photo Eye Safety System 17

Travel Limit Adjustment– I. UP Limit 18

Travel Limit Adjustment– II. DOWN Limit 19

Auto Force Adjustment 20

Final Adjustment and Testing 21

Operation

Programming 3-Button Remote 22

Programming Keyless Entry Pad 23

Important Safety Instructions 24

Operating the Opener 25

Door Status vs. Activation 26

Backup Battery Installation / Battery and Status Indicator 27

Backup Battery Features / Motion-Sensing Light 28

Maintenance 29

Troubleshooting 29-30

Repair Parts and Service

Rail Assembly Parts / Installation Parts / Accessories 31

Opener Assembly parts 32

Warranty 33

DO NOT connect power Please connect power

Symbols and Icons

!WARNING READ WARNINGS CAREFULLY to prevent SERIOUS INJURY or DEATH caused by

electrocution or mechanical hazard.

Installation hardware are

shown in actual size

*See Accessories in Repair Parts section of this manual for purchase information.

Beeps from built-in buzzer of the opener

— Door arms / Mounting Opener

Inventory

x 2

Clevis Pin — Pulley

3/8” x 1-3/4”

Hitch Pin — Locking Clevis Pins

x 5

Lag Screw #12 x 1”— Photo Eye System

Lag Screw 5/16” x 1-1/2”

— Header Bracket / Mounting Opener

Bolt 5/16” x 1”

Drywall Anchor

- Push Button

x 2

Screw #6 x 1-1/4”

- Push Button

5/16” Flange Nut

x 4 x 4

x 4

x 1

Emergency Release Handle + Rope

Literature + Safety Labels

Photo Eye Safety System

Opener Unit + Light Lens Cover

Header

Bracket

Door Bracket

Trolley Pulley

Rail — Header Segment

Rail — Middle Segments x3

INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE)

Hanging

Brackets

Insulated Staples

— Securing wires

x 2

Self-Threading Screw 1/4” x 5/8”

Door Bracket

Trolley Shaft

Master Link Set

—Trolley Shaft

x 1

Rail — End Segment with Trolley Stop Bolt

Clevis Pin — Door arms

5/16” x 1”

Clevis Pin — Header Bracket

5/16” x 1-1/2”

Two 3-Button

Mini Remotes Door Control Console Wireless Keyless Entry Keypad

Drywall Anchor

x 2

Screw #6 x 1”

Drywall Anchor

Screw #6 x 1”

Sprocket Cover

x 1

Door Arms

Belt

Preparation

Level

Tape Measure

Hack Saw

Pencil

Drill, 3/16” and 5/16” Drill Bits

Tools Required

Step Ladder

Screwdriver

Hammer

Sectional Garage Door BEFORE beginning Installation:

1. Disable locks and remove all ropes connected to the

garage door.

2. Perform the following door test to ensure your door is

balanced and in good working condition.

To Test Your Garage Door

1. Raise and lower the door to check if there is any sticking or

binding.

2. Check for loose hinges, damaged rollers, frayed cables and

damaged or broken springs.

3. Lift the door approximately halfway and release. The door

should stay at the point under proper spring tension.

Call a qualified garage door service technician if your door binds,

sticks or is unbalanced.

!WARNING

To prevent SERIOUS INJURY or DEATH:

- Before beginning installation of the opener please complete the following test to ensure that your door is

balanced and in good working condition.

- A poorly balanced door can cause serious injury and damage to the opener.

- Always have a qualified garage door service technician make any required adjustments and/or repairs to

your door before proceeding with installation.

- DISABLE ALL LOCKS and REMOVE ALL ROPES connected to the garage door BEFORE installing

and/or operating the opener.

To prevent damage to the door and opener:

- DO NOT connect power until instructed.

- Operate this opener with AC 120V/60Hz power supply ONLY.

Pliers

Adjustable Wrench Ratchet with

5/16”, 7/16” and 1/2” sockets

DO NOT REUSE PARTS FROM ANOTHER BRAND OF OPENER!!!

Rail and Trolley Assembly

!WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers clear from sprocket during operation.

- Wear gloves when installing belt.

- Keep hands and fingers away from joints and possible sharp edges.

Trolley direction (Top View)

!CAUTION

- DO NOT connect power until instructed.

- To prevent INJURY, keep hands and fingers

away from joints and possible sharp edges.

- Wear gloves when installing chain/belt and cable.

When connecting the rails ensure they are securely connected as shown

above. To apply additional force tap gently on the end of the rail with a

rubber mallet*.

*Only use a soft rubber mallet to tap on the end of the rails as other tools

may damage the rail.

Rail — Header Segment

Rail — Middle Segments

(tapered) x 3

Rail — End Segment (tapered)

with Trolley Stop Bolt

Fig.1

Loosely connected

Securely connected by applying force

To Assemble Rail and Opener

1. Prepare the rails as shown in Fig.1.

2. Connect the rails starting with the Header Segment. Insert the tapered ends into open ends, apply any additional

force necessary by tapping the Rail on padded flooring. Ensure the End Segment has Trolley Stop Bolt facing up.

Make sure the rails are securely joined together as shown.

3. Slide the Trolley onto the rail from the Header Segment. Make sure the arrow is pointing towards the door as shown .

4. Insert the Rail - End Segment into the Rail Bracket on the Opener. Secure End Segment to Bracket as described on

next page.

* VERY IMPORTANT! *

Right

Wrong

Rail Bracket

Installing the Belt

!WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers clear from sprocket during operation.

- Wear gloves when installing the belt.

- Keep hands and fingers away from joints and possible sharp edges.

To Secure the Rail on the Opener

With the End Segment of the rail fully inserted into the Rail

Bracket, insert a 5/16” x 1-1/2” Clevis Pin through the hole and

lock it into position with a Hitch Pin as shown in Fig.1.

To Assemble the Header Section of Rail

See Figure 2 for steps 1 through 7.

1. Place the belt beside the rail as shown

2. Insert a screwdriver into the hole approximately 10-1/4” from

the end of the Rail - Header Segment. Slide the trolley

against this screw driver. The trolley must stay in this posi-

tion for proper alignment of the belt.

3. Pass the belt end with Trolley Shaft Connector through the

slot on the Rail - Header Segment.

4. Insert the Pulley into the slot to the right of the belt.

5. Secure the Pulley by inserting the 3/8” x 1-3/4” Clevis Pin

through the top of the rail.

6. Lock the Clevis Pin with a Hitch Pin. Rotate the Pulley to

ensure it spins smoothly.

7. Connect the Trolley Shaft to the Trolley Shaft Connector on

the belt, using the Master Link Set.

8. Slide the Trolley Shaft into the Trolley until you hear a "click"

when they lock together. See Fig. 3.

Clevis Pin - 5/16” x 1-1/2”

Hitch Pin

Fig.1

Hitch Pin

Clevis Pin

Rail Bracket

Clevis Pin — 3/8” x 1-3/4”

Hitch Pin

Trolley Shaft

Clevis Pin

Pulley

Fig.2

Trolley Shaft

Fig.3

Trolley Shaft Connector

Screwdriver

Opener Unit

Garage Door Trolley

Slide trolley shaft into trolley to lock

10-1/4” Trolley

To Connect and Tension the Belt

1. With the trolley positioned against the screwdriver, pull the

remaining belt straight along the rail and engage belt teeth

around the sprocket. (Make sure the belt is not twisted

around the rail.) See Fig. 1.

2. After the belt is connected, attach the Sprocket Cover to the

opener with the screw and nut provided. See Fig. 2.

!WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers clear from sprocket during operation.

- Wear gloves when installing chain/belt and cable.

- Keep hands and fingers away from joints and possible sharp edges.

Belt Connector

Tighten until...

Tighten nut

Flange Nut

Installing the Belt

1/4” (6mm)

Base of Rail

Mid-point of rail assembly

Belt

Top of Rail

Actual Size

THE SPROCKET COVER MUST BE SECURELY INSTALLED!!

3. Rotate the Belt Connector towards the Trolley Shaft until the

belt is slightly loose about 1/4” (6mm) above the base of the

rail. Refer to the actual-sized illustration below for proper belt

tension. See Fig. 3.

4. Tighten the Flange Nut on Trolley Shaft against the Belt

Connector. See Fig. 4.

Remove the screwdriver holding the trolley in position on the Rail -

Header Segment.

* VERY IMPORTANT! *

For heavier doors an additional half turn to the belt

connector may be required to eliminate belt slippage.

NOTE: FOR HEAVY DOORS

Sprocket Cover

To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Install only on a properly balanced garage door. An improperly balanced door has the potential to inflict severe

injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before

installing the opener.

3. Remove all ropes and remove or make inoperative all locks connected to the garage door before installing

opener.

4. Where possible, install the door opener 7 feet or more above the floor. For products having an emergency

release, mount the emergency release within reach, but at least 6 feet above the floor and avoiding contact

with vehicles to avoid accidental release.

5. Do not connect the opener to source of power until instructed to do so.

6. Locate the push button: (a) within sight of door, (b) at a minimum height of 5 feet so small children are not able

to reach it, and (c) away from all moving parts of the door.

7. Install the Entrapment Warning Label next to the wall-mount push button in a prominent location. In case the

adhesive does not adhere on the surface, the label should be attached to the surface by mechanical means.

8. After installing the opener, the door must reverse when it contacts a 1-1/2-inch high object (or a 2 by 4 board

laid flat) on the floor.

Important Installation Instructions

Place entrapment warning label on wall next to garage door control.

!WARNING

IMPORTANT INSTALLATION INSTRUCTIONS

To Install Header Bracket

Note: Installation procedures may vary according to door

type.

1. While inside your garage, close the door and mark the

vertical centerline of the garage door. Extend the line onto

the header wall above the door spring.

2. Open the door to the highest point of travel. Mark a line on

the header wall 2“ (5cm) above the highest point of travel.

Note: DO NOT install the header bracket over drywall. In some

installations, it may be necessary to install a 2x4 across two wall

studs to create a suitable location for the header bracket.

If installing into masonry, use concrete anchors (not provided).

Wall-Mounting

As shown in Fig.2, place the header bracket on the vertical

centerline in direction shown.

Mark and drill two 3/16” holes. Fasten the header bracket

securely to a structural support using two 5/16” x 1-1/2” lag

screws.

Alternative Ceiling-Mounting

Ceiling-mounting is suggested ONLY when clearance is minimal.

Extend the vertical centerline onto the ceiling as shown in Fig.3.

Center the header bracket on the vertical mark, no more than

6” (15cm) from the header wall. Mark and drill holes to fasten the

header bracket securely to a structural support.

Mounting Header Bracket

OPENER

MAX. 6” (15cm)

Highest Point of Door Travel

Vertical Centerline

Horizontal Line

Finished Ceiling

Lag Screw

5/16” x 1-1/2”

!WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- The header bracket MUST be SECURELY fastened to the structural support on the mounting wall or

ceiling, otherwise the door may not reverse when required. DO NOT install the header bracket over drywall.

- Concrete anchors MUST be used when mounting the header bracket into masonry.

- NEVER try to loosen, move or adjust garage door springs, cables, pulleys, brackets, or hardware.

- Contact a qualified garage door service technician if your door binds, sticks or is unbalanced. An unbal-

anced door might not reverse when required.

Vertical Centerline

Fig.2 (Wall-Mounting) Fig.3 (Ceiling-Mounting)

7ft door

8ft max

8ft door

9ft max

Fig.1

Ceiling

Header Bracket

Header Wall

2” (5cm) clearance

Door Track

Door

Highest Point of Door Travel

Support block on floor

Door Spring

* VERY IMPORTANT! *

Max recommended rail height from floor

 7ft door = 8ft max height

 8ft door = 9ft max height

MAX RAIL HEIGHT

Floor

Attaching Rail to Header Bracket and Mounting Door Bracket

!CAUTION

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Horizontal and vertical REINFORCEMENT is needed for fiberglass, aluminum or lightweight steel garage

doors BEFORE installing the door bracket. Contact your door manufacturer for reinforcement options.

Fig.1

Fig.2 Fig.3

Self-Threading

Screw - 1/4” x 5/8”

Vertical Centerline of Door

(a) (b) (c)

2-4” (5-10cm)

Top Edge of Door

To Attach the Opener to the Header Bracket

1. As shown in Fig.1, use the packaging carton as temporary

support for the opener. Place the opener on carton to

prevent damage.

2. Align the mounting hole on the header rail to the mounting

hole on the Header Bracket.

3. Connect the header rail and the door bracket together with

a 5/16” x 1-1/2” clevis pin and lock it in place with a hitch

pin.

To mount the Door Bracket

Note: Some door reinforcement kits may provide direct

attachment of the door arm to the reinforcement bracket. If you

have a door reinforcement bracket with this option, skip this step

and proceed with the next step “mounting opener to ceiling”.

1. Position the door bracket on the centerline of the door

approximately 2” - 4” (5-10cm) below the top edge of the

door, as shown in Fig.2.

2. Depending on the construction of your door, install using

one of the steps shown if Fig. 3 below:

For lightweight steel doors, with factory equipped

vertical steel reinforcement and horizontal strut.

(a) Mark and drill two 3/16” holes. Make sure not to drill

through the garage door. Secure the door bracket with two

1/4” x 5/8” self-threading screws (provided) as shown in

Fig.3(a).

(b) Alternative installation: Drill two 5/16” holes through the

door. Secure the door bracket using two 5/16” bolts, lock

washers and nuts (not provided) as shown in Fig.3(b). The

length of bolts will depend on the thickness of your door.

Wood door

Secure the door bracket using two 5/16” carriage bolts,

washers and nuts (not provided) as shown in Fig.3(c). The

length of bolts will depend on the thickness of your door.

Note: DO NOT use Self-Threading Screws on a wood door.

Carton

Hitch Pin Clevis Pin - 5/16” x 1-1/2”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Garagentoröffner Handbücher

Craftsman

Craftsman 139.53998SRT Bedienungsanleitung

Craftsman

Craftsman 39535006 Bedienungsanleitung

Craftsman

Craftsman 139.3043 Bedienungsanleitung

Craftsman

Craftsman 139.53939D Bedienungsanleitung

Craftsman

Craftsman CMXEOCG781 Bedienungsanleitung

Craftsman

Craftsman 139.53985DM Bedienungsanleitung

Craftsman

Craftsman 139.53985D Bedienungsanleitung

Craftsman

Craftsman 139.653100 Bedienungsanleitung

Craftsman

Craftsman 139.18489D Bedienungsanleitung

Craftsman

Craftsman 139.53990 Bedienungsanleitung

Craftsman

Craftsman 139.53990DS Bedienungsanleitung

Craftsman

Craftsman 139.53669SRT Bedienungsanleitung

Craftsman

Craftsman 139.5398511 Bedienungsanleitung

Craftsman

Craftsman 200.57933 Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Craftsman

Craftsman 139.53919D Bedienungsanleitung

Craftsman

Craftsman 53479 Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Craftsman

Craftsman 139.536481DM Bedienungsanleitung

Craftsman

Craftsman 139.53939D Bedienungsanleitung

Craftsman

Craftsman 139.5364812 Bedienungsanleitung

Craftsman

Craftsman 139.53491SRT Bedienungsanleitung

Craftsman

Craftsman 57993 Bedienungsanleitung

Craftsman

Craftsman 139.53515SR - I/2HP Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung