Craftsman 486.24227 Bedienungsanleitung

Operator's Manuat

S S

Model No. 486,24227

CAUTION:

Before using this product, read

this manuaU and follow aH Safety

RuUes and Operating Instructions.

mMPORTANT: For Missing Parts or

AssembUy Questions Call 866-576-8388

• Safety

,, AssembLy

,, Operation

• Maintenance

,, Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www, sears,com/craftsman

PRINTED IN U.S.A. FORM NO. 49950 (11/05)

MAINTENANCE/STORAGE ........................................... 9

REPAIR PARTS iLLUSTRATiON ................................. 10

REPAIR PARTS MST ................................................... 11

PARTS ORDERING/SERVICE ........................ Back Page

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.

Exercise caution at all times when using power equipment.

* This sun shade does not provide protection against

exhaust fumes, collision, rollover or other accidents.

* Read the sun shade and vehicle owner's manuals

and know how to operate your vehicle and sun shade

before using the sun shade attachment.

* Be sure there is adequate ventilation when using the

tractor and sun shade in confined areas.

* The sun shade will restrict your field of vision in some

directions. Use extra caution when operating your

tractor with the sun shade attached.

* Watch out for low tree limbs or other overhead

obstructions that may not previously have interfered

with operation of the tractor. The extra height of the

sun shade may cause these objects to become

obstacles.

* Check the area of operation thoroughly before using

the tractor.

Look for this symbol to point out important safety precautions, it means--Attention!! Become

alert!! Your safety is involved.

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Sun Shade fails due to a defect in

material or workmanship within one year from the date of purchase, call I°800°4-MyoHOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., B817WA, Hoffman Estates, tL 60179

The model number and serial numbers wil! be found on a

decal attached to the base assembly.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.24227

SHOWN FULL SIZE

\\\\

NOT SHOWN FULL SSZE

y ......

REF.

! QTY. !

DESCRIPTION

Carriage Bolt, 5/16" x 2o3/4"

Carriage Bolt, 5/16 x 2"

Hex Bolt, 5/16" x 2"

Hex Bolt, 1/4 x 1ol/2"

Hex Bolt, 5/16 x 1"

Nylock Nut, 1/4"

RER QTY. DESCRIPTION

G 5 Nylock Nut, 5/16"

H 4 Flat Washer, 5/16"

I 1 Carriage Bolt, 1/4 x 1"

J 4 Spacer

K 4 Adhesive Pad

L 2 Plastic Knob

1. Upperbasetube

2. TopTubes(2)

3. BaseLegTubes(2)

4. BaseLegTube(w/Flat)

5. UprightTubes(2)

6. RightSupportBracket

7. LeftSupportBracket

8. BaseBracket

9. LeftBaseBracket

10.RightBaseBracket(stampedwithR)

11.U-Tube

12.VinylCanopy

13.SupportRods(3)

jlO

_fJJ J f ........

112

TOOLS REQUIRED FOR ASSEMBLY

(2) 7/16" Wrenches

(2) 1/2" Wrench

(1) 1/2" or 9/16" Socket Wrench

REMOVAL OF PARTS FROM CARTON

Remove all parts and hardware packages from the

carton. Lay out parts and hardware and identify using

the illustrations on pages 3 and 4.

NOTE: Not all of the supplied parts and hardware will be

needed for one particular tractor. Unneeded items may be

discarded after assembly has been completed.

NOTE: Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

CAUTION: Make sure tractor seat raises

and lowers freely after attaching Sun

Shade. The tractor's operator presence

safety switch will not operate if seat is

stuck down.

STEP 1: (SEE FIGURE 1)

, Look under the front of your tractor, If there is a single

mower deck suspension bracket located underneath

the middle of the front axle, continue on to step 2, If

your tractor does not have a mower deck suspension

bracket underneath the middle of the front axle, skip

to step 5 on page 6 for tractors with dual suspension

brackets,

"-----_ BRACKET ---_--J

FIGURE 1

iNSTRUCTiONS FORTRACTORS WITH

SINGLE SUSPENSION BRACKET

STEP 2: (SEE FIGURE2)

, The four holes in the base bracket are unequal in

height, Place the base bracket on a flat surface with

the holes that are higher facing away from you,

, Attach the right side of the base bracket to the forth

and fifth holes in the flattened base leg tube using two

5/16" x 2" carriage bolts (B) and 5/16" nylock nuts (G),

Make only finger tight.

, Attach the left side of the base bracket to the forth

and fifth holes in one of the base leg tubes using two

5/16" x 2" carriage bolts (B) and 5/16" nylock nuts (G).

Make only finger tight.

, Attach the long end of the right support bracket to the

flattened end of the right base leg tube using a 1/4" x

1" carriage bolt (I) and 1/4" nylock nut (F). Make only

finger tight.

Attach the left support bracket to the left base leg tube

using one 5/16" x 2" hex bolt (C) and 5/16" nylock nut

(G)=Make only finger tight=

1/4" x 1"

CARRmAGE BOLT (I)

R{GHT

SUPPORT

BRACKET

5/16" NYLOCK NUT (G)

1/4" NYLOCK

NUT (F)

5/16" NYLOCK

NUT (G) SHORT END

5/16" × 2"

BEX BOLT (C) THIS HOLE

IS HIGHER

LEFT

SUPPORT

BRACKET

BASE LEG TUBE

(FLATTENED)

5/16" x 2"

CARRmAGE BOLT (B)

BASE BRACKET

FIGURE 2

STEP 3: (SEE FIGURE 3)

. insert the ends of the base leg tubes into the upper

base tube.

UPPER BASE TUBE

BASE TUBELEGS

FIGURE 3

STEP 4: (SEE FIGURE 4)

. Raise the tractor seat and remove the seat springs and

the four bolts from the rear fender using a 1/2" socket.

. Place the base leg tubes onto the rear fender. Attach

the front support brackets to the front holes in the

fender reusing the bolts that were removed. If seat

springs were mounted to front holes, see note below.

Do not tighten completely.

. Attach the base bracket and the seat springs to the

rear holes in the fender using the new 5/16" x 1" bolts

(E) and 5/16" flat washers (H) supplied with the Sun

shade. If seat springs were mounted to front holes, see

note below. Do not tighten completely.

. Tighten first the nuts and bolts that fasten the base leg

tubes to the base bracket and front support brackets.

. Center the base leg tubes on the rear fender and then

tighten, using moderate force, the bolts fastening

the base bracket and the front support brackets to

the fender=Overtightening the bolts may damage the

threaded holes in the fender=

PROOEEDTO STEP 8 ON PAGE 7

NOTE: If seat springs were mounted to front holes, use

5/16" x 1" bolts (E) and 5/16" flat washers (H) to attach

seat springs and front support brackets to front holes.

Use origina! bolts to attach base bracket to rear holes.

5/16" x 1"

ORIGINAL HEX BOLT (E)

BOLT 5/16" WASHER (H)

SPRING

'SEE NOTE)

iNSTRUCTiONS FOR TRACTORS WITH DUAL

SUSPENSION BRACKETS

STEP 5: (SEE FIGURE5)

Attach the right base bracket to the front holes of a

base leg tube that does not have a flattened end,

using two 5/16" x 2o3/4" carriage bolts (A), two

spacers (J) and two 5/16" nylock nuts (G). Make only

finger tight. Repeat for the left base bracket.

SPACER (J)

5/16" x 2o3/4"

CARRmAGE BOLT (A)

LEFT BASE

BRACKET

5/16" NYLOCK NUT (G)

BASE LEG TUBE

RmGHTBASE BRACKET

FIGURE 5

STEP 6: (SEE FIGURE6)

. Insert the ends of the base leg tubes into the upper

base tube.

UPPER BASE TUBE

BASETUBELEGS

FIGURE 6

FIGURE 4

STEP 7: (SEE FIGURE 7)

, Raise the tractor seat and remove the springs and

bolts from the rear fender using a 1/2" socket for GT

tractors or a 9/16" socket for LTtractors.

, Place the base tube assembly onto the rear fender.

Align the front or rear slot in the base brackets with

the spring mounting holes. Check for clearance with

the seat lowered and the rear bagger (optional)

attached. If needed, reposition the base brackets to a

different set of holes in the base tubes.

, If the base leg tubes rub against the fender, attach the

adhesive pads (K) to the bottom of the base leg tubes.

° Attach the seat springs and the base brackets to the

rear fender using the spring bolts that you removed.

On GT tractors, if the spring bolts were less than 1"

long, use the 5/16" x 1" bolts (E) and 5/16" washers

(H) supplied with the Sun Shade. Align the base leg

tubes on the rear fender. Use a 1/2" socket (GT) or

a 9/16" socket (LT) to tighten the seat spring bolts

using moderate force. Do not overtighten. Next,

tighten the bolts fastening the base leg tubes to the

base brackets.

J ............... _ ORmGmNAL HOLT

/_'- OR BOLT (E) AND

x\I

COMPLETING ASSEMBLY - ALL TRACTORS

STEP 8: (SEE FIGURE 8)

, Assemble the upright tubes to the base assembly

using a 5/16-18 x 2" carriage bolt (B), 5/16" flat

washer (H) and plastic knob (L) for each tube.

NOTE: Loosen bolts attaching base tubes to mounting

bracket if alignment of upright tubes is difficult.

PLASTUC

KNOB (L)

! 5116" x 2"

[ HARRIAGE BOLT (g)

FIGURE 8

5/16" FLAT

WASHER (R)

STEP 9: (SEE FIGURE 9)

, Assemble the top tubes to the upright tubes using

two 1/4" x 1-1/2" hex bolts (D) (outside) and two 1/4"

nylock nuts (F) (inside). Do not tighten yet.

, Fit the front U-tube onto the top tubes. Fasten the

tubes together using two 1/4" x 1-1/2" hex bolts

(D) (outside) and two 1/4" nylock nuts (F) (inside).

Tighten aH loose bolts and nuts.

, Fit the three support rods into the holes in the top

tubes, with the rods arching upward. Do not over

bend the rods when installing.

1t4" x lq/2"

HEX HOLT (D) SUPPORT ROD

UoTUHE

1/4" NYLOCK

NUT (F) /NUT (F)

1/4" x 1-1/2" J

HEX BOLT (D'J '

FIGURE 9

STEP 10: (SEE FIGURE 10)

, Place the vinyl canopy on top of the tubing frame,

fitting the front of the viny! canopy around the front

U-tube, Secure the nylon mesh to the upright tubes

using the ties located on the corners of the mesh,

FIGURE 10

Read this owner's manual and safety rules before operating your tractor with the sun shade.

CAUTION: This sun shade does not

provide protection against exhaust fumes,

collision, rollover or other accidents.

CAUTION: Watch out for low tree limbs

and other overhead objects which may

interfere with the sun shade.

Check the area of operation thoroughly before using

the tractor with the sun shade. The added height of

the sun shade and a reduced field of vision require

extra caution during operation.

Remove the upper sun shade frame and canopy

before you transport the tractor in an open truck or

open trailer=

CAUTION: Never transport the tractor in

an open truck or open trailer while the sun

shade is attached.

CUSTOMER RESPONSiBiLiTiES

Read and follow the maintenance schedule and the maintenance procedures listed in this section.

MAINTENANCE SCHEDULE

Fill in dates as you

comptete regular service.

Check for loose fasteners

Cteaning

.......... ServiceOates

xx x

CHECK FOR LOOSE FASTENERS

, Before each use make a thorough visua! check of

the sun shade for any bolts and nuts which may have

loosened. Retighten any goosebolts and nuts.

CLEANING

, Wipe loose dirt and debris from the vinyl canopy after

each use, The vinyl canopy can be washed using mild

liquid soap and water,

STORAGE

, Clean the vinyl canopy thoroughly with mild liquid

soap and water. Allow to dry before storing.

Store the sun shade in a clean, dry area away from

direct sun light.

REPAIR PARTS FOR MODEL 488.24227 SUN SHADE

12"

2O\

2 i

\\\

15 \

9,\

9 \

8 10

o ...... 17

Andere Handbücher für 486.24227

Inhaltsverzeichnis

Andere Craftsman Rasenmäherzubehör Handbücher

Craftsman

Craftsman BRUSH GUARD 486.246283 Bedienungsanleitung

Craftsman

Craftsman 132.24607 Bedienungsanleitung

Craftsman

Craftsman 917.248911 Bedienungsanleitung

Craftsman

Craftsman 132707 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman 536.330600 Bedienungsanleitung

Craftsman

Craftsman 917.249740 Bedienungsanleitung

Craftsman

Craftsman 486.248471 Bedienungsanleitung

Craftsman

Craftsman 917.249781 Bedienungsanleitung

Craftsman

Craftsman 917.330772 Bedienungsanleitung

Craftsman

Craftsman 917.249650 Bedienungsanleitung

Craftsman

Craftsman 48"MOWER 917.24985 Bedienungsanleitung

Craftsman

Craftsman 917.242450 Bedienungsanleitung

Craftsman

Craftsman 917.249980 Bedienungsanleitung

Craftsman

Craftsman 486.24443 Bedienungsanleitung

Craftsman

Craftsman 486.245042 Bedienungsanleitung

Craftsman

Craftsman 536.249810 Bedienungsanleitung

Craftsman

Craftsman 24919 Bedienungsanleitung

Craftsman

Craftsman 917.248940 Bedienungsanleitung

Craftsman

Craftsman Sun Shade 486.24226 Bedienungsanleitung

Craftsman

Craftsman 358.792404 Bedienungsanleitung

Craftsman

Craftsman 486.24311 Bedienungsanleitung

Craftsman

Craftsman 917.248970 Bedienungsanleitung

Craftsman

Craftsman 917.249890 Bedienungsanleitung

Craftsman

Craftsman 292670 Bedienungsanleitung

Beliebte Rasenmäherzubehör Handbücher anderer Marken

Ariens

Ariens 891008 Bedienungsanleitung

Rover

Rover 108 - 109 Bedienungsanleitung

Toro

Toro 112-5803 Bedienungsanleitung

Snapper

Snapper 1690047 Bedienungsanleitung

Scag Power Equipment

Scag Power Equipment GC-F4 Bedienungsanleitung

RHINO

RHINO 800 Bedienungsanleitung

Exmark

Exmark Quest 126-7506 Bedienungsanleitung

Snapper

Snapper 1685167 Bedienungsanleitung

Cub Cadet

Cub Cadet 19B70029100 Bedienungsanleitung

Stihl

Stihl AMK 043.1 Bedienungsanleitung

MTD

MTD 753-0873 Handbuch

Toro

Toro 30810 Bedienungsanleitung

Bush Hog

Bush Hog RG60 Bedienungsanleitung

Land Pride

Land Pride RCF2760 Bedienungsanleitung

Simplicity

Simplicity 211 Bedienungsanleitung

Toro

Toro Z Master 116-0231 Bedienungsanleitung

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Bedienungsanleitung

Excel

Excel Two Bag Catcher Bedienungsanleitung