Craftsman 486.248472 Bedienungsanleitung

Operator's Manua_

CRAFTSHAN+

Mode_ No. 486.248472

FRONT SCOOP TRACTOR ATTACHMENT DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

CAUTION:

Before using this product, read

this manual and follow all Safety

Rules and Operating Instructions.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www. sears.com/c raftsman

PRINTED iN U.S.A. FORM NO. 48205 (REV. 5/01/07)

WARRANTY .................................................................... 2

SAFETY RULES .............................................................. 3

FULL SIZE HARDWARE CHART .................................... 4

CARTON CONTENTS ..................................................... 6

ASSEMBLY ...................................................................... 7

OPERATION .................................................................. 17

MAINTENANCE ............................................................ 18

TROUBLESHOOTING ................................................... 19

REPAIR PARTS ILLUSTRATION .................................. 20

REPAIR PARTS LiST ..................................................... 21

SLOPE GUIDE .............................................................. 23

PARTS ORDERING/SERVICE ......................... Back Page

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Front Scoop Tractor Attachment fails

due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4=MY=HOME® to arrange

for free repair (or replacement if repair proves impossible).

if this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., [:)817WA, Hoffman Estates, tL 60179

The model number and serial number will be found on a

decal attached to the bucket.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.248472

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment,

Exercisecautionatalltimeswhenusingpowerequipment,

® Readthisoperator'smanualbeforeattemptingto

assembleoroperatethescoopattachment,

® Readthevehicleowner'smanua!andknowhow

tooperateyourvehiclebeforeusingthescoop

attachment,

o Nevercarrypassengersinthescoopbucket,Ithas

notbeendesignedtocarrypassengers,

o Neverallowchildrentooperatethevehicleorthe

scoopattachment,

o Donotallowadultstooperatethevehicleorscoop

attachmentwithoutproperinstructions,

® Alwaysbeginwiththetransmissioninfirst(low)and

graduallyincreasespeedasconditionspermit,

® Drivethetractoratreducedspeedoverroughterrain

andhillsidesornearcreeksandditchestoprevent

tippingoverandtossofcontro!.Donotdrivetooclose

toacreekorditch,

® Neverramthescoopintomateria!athighspeed,

® Vehiclebrakingandstabilitymaybeaffectedwith

theattachmentofthisscoop,Donotfillthescoop

tomaximumweightcapacitywithoutcheckingthe

capabilityofthevehicletosafelydriveandstopwith

thescoopattached,

o Beforeoperatingvehicleonanygrade(hill)refer

tothesafetyrulesinthevehicleowner'smanual

concerningsafeoperationonslopes,Referalsotothe

slopeguideonpage23ofthismanual,Stayoff steep

slopes!

® Followmaintenanceandlubrication instructions as

outlined in this manual

Look forthis symbol to point out important safety precautions, It means-- Attention?! Become

alert!! Your safety is involved. /

These and other accessories are recommended for use with your unit, Cal! 1=800=4=MyoHOME®to find out ifthey are available,

If available, they may be purchased at most Craftsman outlets or by calling 1-800-4=MyoHOME®,

WHEEL WEIGHT TIRE CHAINS

i_J K

JjH

cc DD

PARTS NOT SHOWN FULL SIZE

MM NN

QQ RR

PARTS BAG CONTENTS

Not all parts will be needed for fit-up to any one tractor,

Discard unneeded parts after assembly is finished,

RER QT_

A 2

B 2

C 3

D 2

E 6

F 4

G 5

H 2

I 1

J 6

K 2

L 2

M 1

N 2

O 1

P 2

Q 2

R 2

S 8

T 12

U 5

V 1

DESCRIPTION

Hex Bolt, 5/8" x 1-1/2"

Hex Bolt, 1/2" x 1-3/4"

Hex Bolt, 1/2" x 1"

Hex Bolt, 3/8" x 1-1/4"

Hex Bolt, 3/8" x 1"

Hex Bolt, 5/16" x 1"

Hex Bolt, 5/16" x 1-3/4"

Hex Bolt, 1/4" x 1-3/4"

Hex Bolt, 1/4" x 2"

Carriage Bolt, 3/8" x 1"

Carriage Bolt, 5/16" x 1"

Carriage Bolt, 1/4" x 3/4"

Slotted Truss Head Bolt, 10-32 x 5/8"

Nylock Nut, 5/8"

Hex Lock Nut, 1/2"

Nylock Nut, 1/2"

Nylock Jam Nut, 1/2"

Hex Nut, 3/8"

Nylock Nut, 3/8"

Nylock Nut, 5/16"

Nylock Nut 1/4"

Nylock Nut, #10-32

RER

QTY.

DESCRIPTION

Spacer, 1" Long

Spacer, 1/2" Long

Hairpin Cotter, Long

Hairpin Cotter, Short

Cotter Pin, 1/8" x 1-1/4"

Cotter Pin, 1/8" x 1-1/2"

Lock Washe r,3/8"

Washer, 1/4"

Washer, 5/16"

Washer, 3/8" (Small)

Washer, 1/2" (Small)

Washer, 3/8" (Large)

Washer, 5/8"

Washer, 1/2" (Large)

Washer, 3/4"

Washer, 1"

Clevis Pin

Compression Spring

Slotted Stop Bracket

Cable Tie

Tilt Stop Bracket

Hose Clip

1, BucketAssembly

2, PinStopBracket

3, LiftFrameAssembly

4, LiftBracketAssembly

5, TiltAnchorAssembly

6, Right(Long)SidePlate

7, Left(Long)SidePlate

8, Right(Short)SidePlate

9, Left(Short)SidePlate

10,DumpControlRod

11,LiftStrapAssembly(2)

12,TiltBracketAssembly

13,AttachmentRod

14,DumpHandleTube

15,LiftHandleTube

16,DumpControlPin

17,DumpPivotBracket

18,DumpHandleTubeExtension

19,LiftHandleTubeExtension

19\

TOOLS REQUIRED FOR ASSEMBLY

(1)

(2)

(1)

Standard Screwdriver

15/16" Wrenches (one should be box-end)

3/4" Wrenches

9/16" Wrenches

1/2" Wrenches

7/16" Wrenches

3/8" Wrench

ADDUTmONAL iTEMS NEEDED

Ruler or Tape Measure

Grease

REMOVE PARTS FROM CARTON

,, Remove the hardware pack and all loose parts from

the carton,

Lay cardboard on floor to help prevent scratching of

painted parts.

Lay out and identify all the parts and hardware as

shown on pages 4 through 6.

5/16" WASHERS (EE)

5/16"'

NYLOCK NUT (T ;/8"x 1ol/4"

..- HEX BOLT(D)

318"NYLOCK NUT (S) 3/8" HEX NUT(R)

FIGURE 1

ASSEMBLE SCOOP

STEP 1: iNSTALL TWO BOLTS

(SEE FIGURE 1)

Assemble two 3/8" x 1-1/4" hex bolts (D) and 3/8" hex

nuts (R), threading the nut all the way onto the bolt

until it is tight against the head of the boll

Install a nut/bolt assembly into the bucket assembly

and fasten using a 3/8" nylock nut (S). Tighten.

Repeat for the other side.

STEP 2: iNSTALL PIN STOP BRACKET

(SEE FIGURE 1)

, Install the pin stop bracket to the top of the bucket

assembly using four 5/16" x 1" hex bolts (F), eight

5/16" washers (EE) and four 5/16" nylock nuts (T).

Leave the bolts loose enough that the position of the

pin stop bracket can be adjusted later.

STEP 3: iNSTALL LIFT FRAME ASSEMBLY

(SEE FIGURE 2)

Apply grease to the mounting surface of the bucket

assembly and the inside of the lift frame arms.

Assemble the lift frame assembly to the bucket

assembly using two 5/8" x 1-1/2" hex bolts (A) and

5/8" nylock nuts (N). Tighten, then loosen the nuts

1/4 turn, or until the lift frame pivots freely.

5/8" x 1-1/2"

HEX BOLT(A)

APPLY

GREASE /^_...

APPLY LIFT FRAME

GREASE ASSEMBLY

5/8" NYLOCK

NUTS (N) APPLY GREASE

5/8" x 1-1/2"

HEX BOLT (A)

FIGURE 2

STEP4: INSTALLLiFTBRACKETASSEMBLY

(SEEFIGURE3)

o Assembletheliftbracketassemblytotheliftframe

assemblyusingtwo5/8"washers(ll)and1/8"x 1ol/4"

cotterpins(AA),

LIFT 118"x 1-114"

ASSEMBLY COTTER

r_. (AA)

I "4 I

LIFT FRAME

ASSEMBLY

FIGURE 3

STEP 6: INSTALL LiFT STRAP ASSEMBLIES

(SEE FIGURE 5)

Loosen the bolts and nuts on the lift strap

assemblies 1/4 turn or until the straps will slide back

and forth, You wilt retighten them later in step 26,

Turn the lift strap assemblies as shown, Insta!l each lift

strap assembly to an arm of the lift bracket assembly

and then secure with a small 1/2" washer (GG) and a

short hairpin cotter (Z),

Position the lower end of each lift strap assembly to

the outside of the lift frame, Fasten to the upper front

holes in the lift frame using a 1/2" x 1" clevis pin (MM),

1/2" long spacer (X) and short hairpin cotter (Z) for

each assembly,

NOTE: The lift strap assemblies may be installed in the

rear mounting holes of the lift frame to increase the Jilt

height, but this will also increase the lifting effort, The

front holes give a lift height of about 6ol/2" and require 28

Jbs,of force to lift a 150 Ib load, The rear holes will give a

lift height of about 8-1/2" and require 35 Ibs, of force,

STEP 5: INSTALL TILT ANCHOR ASSEMBLY

(SEE FIGURE 4)

Assemble the tilt anchor assembly to the lift bracket

assembly using two 1/2" x 1" hex bolts (C) and 1/2"

nylock jam nuts (Q), Tighten.

SHORT HAIRPIN

ARM COTTER (Z)

"\\.. /112"WASHER

_..._../ (SMALL) (GG)

TILT ANCHOR

ASSEMBLY

1/2" x 1"

HEX BOLT (C)

LIFT

BRACKET

1/2" NYLOCK

JAM NUTS (Q)

I112" x 1"

IHEX BOLT (C)

LIFT STRAP

SHORT ASSEMBLY

HAIRPIN /,..

COTTER (Z) "%"0

1/2" SPACER (X) X

UPPER FRONT 1/2" x 1"

MOUNTING HOLE CLEVIS PIN (MM)

FIGURE 5 Bucket removed for clarity

FIGURE 4

STEP7: iNSTALLTILT BRACKET ASSEMBLY

(SEE FIGURE 6 ON NEXT PAGE)

, Loosen the bolts and nuts on the tilt bracket

assembly 1/4 turn or until the two plates of the

assembly wil! slide back and forth, You wilt retighten

them later in step 25.

Lightly apply grease to the end of the arm on the tilt

anchor assembly and instal! the tilt bracket assembly

to the arm using a 1/2" x 1" hex bolt (C) and 1/2" hex

lock nut (O)=Tighten then !oosen the nut 1/4 turn, or

until the tilt bracket assembly pivots freely.

Install the 1/4" x 2" hex bolt (I) through a 1/4" washer

(DD), the 1" !ong spacer (W) and then through

the end of the extension spring on the tilt bracket

assembly= Next, insert the end of the bolt into the hole

in the arm of the tilt anchor assembly and install the

slotted stop bracket (OO), a 1/4" washer (DD) and a

1/4 nylock nut (U) onto the bolt. Tighten.

1/4" NYLOCK NUT (U)

1/4" WASHER (DD)

SLOTTED STOP

BRACKET (OO) \

TILT ANCHOR

ASSEMBLY

1/2" x 1"

HEX BOLT (C)

1/4" WASHER (DD)

1"SPACER(W) /APPLY

1/4" x2" /GREASE

HEX BOLT(I) 1/2" HEX

LOCK NUT (O) TILT BRACKET

ASSEMBLY

FIGURE 6

STEP 8: INSTALL DUMP PIVOT BRACKET

(SEE FIGURE 7)

, Install a 1/8" x 1-1/2" cotter pin (BB) to the inside hole

in the shaft shown in figure 7, and then install a 1"

washer (LL) onto the shaft, Apply grease to the end of

the shaft and install the dump pivot bracket assembly

onto the shaft, Install a 1" washer (LL) onto the shaft

and secure it using a 1/8" x 1=1/2" cotter pin (BB).

1/8" x 1-1/2"

COTTER PIN (BB)

j WASHERS (LL)

1/8" x 1-1/2"

COTTER PIN BB)

DUMP PIVOT

BRACKET

FIGURE 7

STEP 9: iNSTALL DUMP CONTROL ROD

(SEE FIGURE 8)

, Install a 1/8" x 1-1/4" cotter pin (AA) into the inside hole

in each end of the dump control rod, Spread the ends

of the cotter pins and wrap around the rod, Install a 5/8"

washer (ll) onto each end of the control rod,

Install the dump control rod to the dump pivot bracket

and bucket. Fasten using two 5/8" washers (ll) and

1/8" x 1-1/4" cotter pins (AA). Spread the ends of the

cotter pins and wrap around the rod.

1/8" x 1-1/4"

COTTER PIN (AA)

5/8" WASHERS (11)

x 1-1/4"

COTTER

PINS (AA)

1/8" x 1-1/4"

COTTER PIN,

5/8" WASHERS (11)

DUMP

CONTROL

ROD

FIGURE 8

STEP10:iNSTALLTILTSTOPBRACKETS

(SEEFIGURE9)

, Installatiltstopbracket(QQ)toeachsideofthe

bucketusinga1/4"x3/4"carriagebolt(L),1/4"

washer(DD)and1/4"nylocknut(U)=Donottighten

thenutsuntilstep27=

TmLTSTOP

BRACKET (QQ)

1/4" NYLOCK

NUT(U) 1/4"x 3/4"J'_

1/4" WASHER (DO) CARRIAGE BOLT (L)

STEP 12: iNSTALL LiFT HANDLE TUBE EXTENSION

(SEE FIGURE 11}

Insta!l the lift handle tube extension on the tift handle

tube using a 1/4" x 1o3/4" hex bolt (H) and 1/4" nylock

nut (U)=

LIFT HANDLE

TUBE EXTENSION

1/4" NYLOCK NUT

1/4" x 1-3/4"

HEX BOLT(H) LIFT HANDLE

_TUBE

FIGURE 11

FIGURE 9

STEP 11: iNSTALL LiFT HANDLE TUBE

(SEE FIGURE 10)

Install the lift handle tube into the index bracket using

two 5/16" x 1-3/4" hex bolts (G) and 5/16" nylock nuts

(T)=

LIFT HANDLE

TUBE

5/16" NYLOCK 5/16" x 1-3/4"

NUTS (T) HEX BOLT (G)

/INDEX

BRACKET

FIGURE 10

STEP 13: iNSTALL LiFT CABLE

(SEE FIGURE 12)

, Connect the hooked end of the lift cable into the index

rod, and install the threaded cable adjuster into the

notch in the top of the index bracket, placing a nut on

each side of the notch=

Adjust the cable adjustment nuts so that when the lift

trigger issqueezed, the bottom of the index rod raises

enough to release from the latched position= The index

rod should also lower far enough to lock in the latched

position when the trigger is released=

Attach the lift cable to the lift handle using three cable

ties (PP)=

LiFT TRUGGER

LIFT CABLE

CABLE

NUTS

INDEX ROD

FIGURE 12

Inhaltsverzeichnis

Andere Craftsman Rasenmäherzubehör Handbücher

Craftsman

Craftsman 33731 Bedienungsanleitung

Craftsman

Craftsman 917.248911 Bedienungsanleitung

Craftsman

Craftsman 917.249160 Bedienungsanleitung

Craftsman

Craftsman 917.248960 Bedienungsanleitung

Craftsman

Craftsman 247.240690 Bedienungsanleitung

Craftsman

Craftsman 132707 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman Mow-N-Vac 486.24505 Bedienungsanleitung

Craftsman

Craftsman GRASS CATCHER 917.24898 Bedienungsanleitung

Craftsman

Craftsman 917.248970 Bedienungsanleitung

Craftsman

Craftsman 486.24443 Bedienungsanleitung

Craftsman

Craftsman 917.249393 Bedienungsanleitung

Craftsman

Craftsman 917.249790 Bedienungsanleitung

Craftsman

Craftsman 536.330600 Bedienungsanleitung

Craftsman

Craftsman 917.249050 Bedienungsanleitung

Craftsman

Craftsman 917.249791 Bedienungsanleitung

Craftsman

Craftsman 536.249810 Bedienungsanleitung

Craftsman

Craftsman 917.248920 Bedienungsanleitung

Craftsman

Craftsman 917.249491 Bedienungsanleitung

Craftsman

Craftsman 48"MOWER 917.24985 Bedienungsanleitung

Craftsman

Craftsman 917.248971 Bedienungsanleitung

Craftsman

Craftsman 917.249662 Bedienungsanleitung

Craftsman

Craftsman 292670 Bedienungsanleitung

Craftsman

Craftsman 917.249650 Bedienungsanleitung

Craftsman

Craftsman 24919 Bedienungsanleitung

Beliebte Rasenmäherzubehör Handbücher anderer Marken

Ariens

Ariens 891008 Bedienungsanleitung

Rover

Rover 108 - 109 Bedienungsanleitung

Toro

Toro 112-5803 Bedienungsanleitung

Snapper

Snapper 1690047 Bedienungsanleitung

Scag Power Equipment

Scag Power Equipment GC-F4 Bedienungsanleitung

RHINO

RHINO 800 Bedienungsanleitung

Exmark

Exmark Quest 126-7506 Bedienungsanleitung

Snapper

Snapper 1685167 Bedienungsanleitung

Cub Cadet

Cub Cadet 19B70029100 Bedienungsanleitung

Stihl

Stihl AMK 043.1 Bedienungsanleitung

MTD

MTD 753-0873 Handbuch

Toro

Toro 30810 Bedienungsanleitung

Bush Hog

Bush Hog RG60 Bedienungsanleitung

Land Pride

Land Pride RCF2760 Bedienungsanleitung

Simplicity

Simplicity 211 Bedienungsanleitung

Toro

Toro Z Master 116-0231 Bedienungsanleitung

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Bedienungsanleitung

Excel

Excel Two Bag Catcher Bedienungsanleitung