Craftsman 919.155350 Bedienungsanleitung

Owners Manual

CAUTION: Read the Safety Guidelines

and All Instructions Carefully Before

Operating.

• Safety Guidelines

• Operation

• Maintenance

• Troubleshooting

• Repair Parts

• Español

D25867 Rev. 0 2/5/02

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman

SPRAY GUN

Model No.

919.155350

2- ENG

D25867

• SAVE THESE INSTRUCTIONS •

IMPROPER OPERATION OR MAINTENANCE OF THIS

PRODUCT COULD RESULT IN SERIOUS INJURY AND

PROPERTY DAMAGE. READ AND UNDERSTAND ALL

WARNINGS AND OPERATING INSTRUCTIONS BEFORE

USING THIS EQUIPMENT.

The Following Hazards Can Occur During The Normal Use Of This Product:

HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT

When paints or materials are

sprayed, they are broken into

very small particles and mixed

with air. This will cause certain

paints and materials to become

extremely flammable and could

result in serious injury or death.

Never spray near open flames

or pilot lights in stoves or

heaters.

Never smoke while spraying.

Provide ample ventilation when

spraying indoors.

RISK OF

EXPLOSION OR

FIRE -

FLAMMABLE

MATERIALS

SAFETY GUIDELINES - DEFINITIONS

Indicates an

imminently hazardous

situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, could result in

death or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, may result in

minor or moderate injury.

Used without the

safety alert symbol

indicates a potentially hazardous

situation which, if not avoided, may

result in property damage.

SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we

use the symbols below. Please read the manual and pay attention to these sections.

This manual contains information that is important for you to know and understand. This information

relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you

recognize this information, we use the symbols below. Please read the manual and pay attention to

these sections.

IMPORTANT SAFETY INSTRUCTIONS

3- ENG D25867

RISK OF

EXPLOSION -

INCOMPATIBLE

MATERIALS

HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT

SPECIFICATIONS

The solvents 1,1,1-Trichloroethane

and Methylene Chloride can

chemically react with the alumi-

num used in most spray equip-

ment, and this gun and cup, to

produce an explosion hazard and

could result in serious injury or

death.

Read the label or data sheet for

the material you intend to spray.

1. Never use any type of

spray coating material

containing these solvents.

2. Never use these solvents

for equipment cleaning or

flushing.

3. If in doubt as to whether a

material is compatible,

contact your material

supplier.

Some paints, coatings and

solvents may cause lung damage,

and burns if inhaled or allowed to

come into contact with skin or

eyes.

Use a NIOSH approved mask

or respirator and protective

clothing designed for use with

your specific application and

spray materials. Some masks

provide only limited protection

against toxic materials and

harmful paint solvent. Consult

with a Safety Expert or Industri-

al Hygienist if uncertain about

your equipment or materials.

RISK TO

BREATHING

RISK FROM

FLYING OBJECTS Certain parts are under pressure

whenever the gun is connected to

a pressurized air line. These parts

may be propelled if the gun is dis-

assembled.

Compressed air may propel dirt,

metal shavings, etc. and possibly

cause an injury.

Prolonged exposure to air spray

can result in permanent damage

to hearing.

Disconnect the gun from the air

line, or completely depressurize

the air line whenever the gun is

to be disassembled.

Never point any nozzle or

sprayer toward a person or part

of the body.

Always wear ANSI 278.1 safety

approved goggles or glasses

when spraying.

Always wear hearing protection

when operating spray equip-

ment.

Air Inlet 1/4 NPT

Maximum Air Pressure 100 psi.

Recommended Operating Air Pressure Range 60 psi.

The cup provided with this gun is designed for siphon feed only, it is ideal for

applying light and medium bodied paints (stain, lacquer) to large size jobs such

as complete auto refinishing. For spraying on larger painting applications the

gun can be used with a remote pressure feed paint tank.

IMPORTANT: This gun is designed to be use with most finishing materials. It is

not designed to be used with corrosive or highly abrasive materials. Using these

materials can lead to poor performance and/or failure of this product.

Before use

●Install a moisture

separator/regulator when there

is a possibility moisture will

damage the surface to be

painted. Install the moisture

separator/regulator as close to

the tool as possible.

NOTE: Liquid water occurs

naturally in air lines as a result

of compression. The moisture

exiting near the compressor is

warm and still in a vapor state which allows it to pass through the moisture

separator. The vapor must travel a minimum of 5 to 10 feet to cool down to

a liquid to be removed by the moisture separator. See Illustration.

●Prior to shipment, this gun was treated with an anticorrosive agent. Before

using this gun make sure that it is carefully flushed with thinner.

4- ENG

D25867

Before disassembly or removal of any part of gun or

attached components, shut off compressor, release

pressure by depressing trigger, and disconnect power source. NEVER

assume system pressure is zero!

TO AVOID CREATING AN EXPLOSIVE ATMOSPHERE,

WORK ONLY IN WELL-VENTILATED AREAS.

USE OF A NIOSH APPROVED FACE MASK IS

RECOMMENDED TO PREVENT INHALATION OF TOXIC

MATERIAL.

DO NOT ATTEMPT TO UNCLOG (BACK FLUSH) SPRAY

GUN BY SQUEEZING TRIGGER WHILE HOLDING

FINGER IN FRONT OF FLUID NOZZLE.

Pressure may vary according to viscosity of material

used. Maximum working pressure of gun is 100 psi. DO

NOT EXCEED PRESSURE LIMIT OF GUN OR ANY OTHER COMPO-

NENT IN SYSTEM!

Prior to daily operation, make certain that all

connections and fittings are secure. Check hose and all

connections for a weak or worn condition that could render system

unsafe. All replacement components such as hose or fittings must have

a working pressure equal to or greater than system pressure.

GENERAL INFORMATION

OPERATION

TO USE

1. Mix material according to the

manufacturer’s instructions. Mixture

should be smooth and easily pourable.

Lumps or foreign particles should be

removed by straining through a

suitable paint filter.

NOTE: If not using the siphon feed setting,

see “Remote Pressure Feed” paragraphs.

2. Remove the material cup (e) from

lid/gun assembly. NOTE: Slide release

lever (f) to the right, rotate lid, and

remove material cup (e).

3. Fill the material cup (e) 3/4 full.

4. Attach material cup (e) to the lid/gun

assembly and slide release lever (f) to

the left to secure in place.

5. Attach air supply line to 1/4 NPT air

inlet (c).

6. Adjust spray pattern.

a. The position of the air cap horns (g) will

determine the spray pattern. Loosen air

cap (h) and rotate horns to achieve

desired pattern. Tighten air cap.

7. Turn fluid control knob (b) clockwise until it

stops, do not force. This will shut off the fluid flow. NOTE: The fluid or den-

sity of “fan spray” is controlled by fluid control knob (b).

8. Adjust air pressure to 60 psi at air compressor.

DO NOT exceed 100 psi.

9. Turn air valve control knob (a)

counterclockwise until first thread is flush with

gun body. NOTE: Air flow is controlled by air

valve control knob (a). DO

NOT turn air valve

control knob or fluid control knob out until

the first thread is past the gun body. They

are under pressure when the gun is triggered

and could leave the gun with force.

NOTE: Care should be exercised when handling

spray gun to avoid damage to the orifice of the air cap and tip of fluid nozzle.

Damage to these parts results in irregular spray patterns.

9. Depress spray gun trigger (d) and gradually turn the fluid control knob (b)

counterclockwise until desired fluid flow is reached. Trigger gun quickly, on

second on-off to test pattern.

NEVER point spray gun at self or any other person. Ac-

cidental discharge of material may result in serious

injury.

NOTE: If gun sprays too fast, decrease the air and fluid pressure. If too slow,

increase the pressure. Turn fluid control knob (b) counterclockwise to increase,

or clockwise to decrease, the fluid flow. Turn air valve control knob (a) counter-

clockwise to increase, or clockwise to decrease, the air flow.

5- ENG D25867

Horizontal position

Vertical position

first thread flush

6- ENG

D25867

Spraying Tips

1. The stroke is made with a free arm motion, keeping the gun at a right angle

to the surface at all points of the stroke. Arching the stroke will result in

uneven application and excessive over spray at each end of the stroke.

2. Depress trigger just before reaching the edge of the surface to be sprayed.

Hold the trigger fully depressed and move the gun in one continuous

motion. Release the trigger when the other edge of the surface is reached,

shutting off the fluid flow, but continue motion a few inches until it is

reversed for the return stroke. When the edge of the surface is reached on

the return stroke, depress the trigger fully again and continue across the

surface.

3. Lap each stroke 50% over the preceding one. Less than 50% will cause

streaks on the finish surface.

Convert to Remote Pressure Feed:

If the material to be sprayed is too heavy for siphon feed or fast application is

desired, convert to the pressure feed setting.

1. Remove the material cup (e) from lid/gun assembly. NOTE: Slide release

lever (f) to the right, rotate lid, and

remove material cup (e).

2. Slide yoke (g),with built in socket

feature, over nut (h). Grip the yoke

and turn to loosen nut, after the nut

is loosened hand turn until lid

assembly can be removed from gun.

3. The gun is now ready to be

connected to any pressure feed tank

with a standard 3/8" straight pipe

female connection. See

manufacturer’s manual for correct

procedure.

4. To operate see steps 5-9 in the “To Use” section to continue.

NEVER point spray gun at self or any other person. Ac-

cidental discharge of material may result in serious

injury.

NOTE: When replacing lid assembly to gun assembly hand tighten nut (h) and

then slide yoke (g) over nut (h) to tighten securely.

Always exercise extreme care when using any solvent

or thinner. Never clean gun near fire, flame, or any

source of heat or sparks. Properly dispose of used cleaning materials.

DO NOT soak entire spray gun in solvent or thinner for

a long period of time as this will destroy lubricants and

possibly make motion uneven. NEVER use lye or caustic alkaline solu-

tion for cleaning. Such solutions will attack aluminum alloy parts of

gun.

It is important that spray gun be cleaned after daily use. Cleaning is accom-

plished by spraying appropriate solvent or thinner through system. Cleaning

NOTE: Clean gun immediately after use. Paint and other materials dry

quickly in the small passages.

1. Turn off air supply to gun.

2. Remove the material cup (e) from lid/gun assembly. NOTE: Slide release

lever (f) to the right, rotate lid, and remove material cup (e).

When using the remote pressure feed method: See manufacturer’s

manual for suggested cleaning of remote cup or tank.

3. Empty material from material cup and replace with a suitable solvent. If

using water based material use mineral spirits to prevent corrosion.

4. Turn air supply on and operate trigger until all material traces have disap-

peared and gun is thoroughly clean.

NOTE: To remove lid assembly from gun assembly, slide yoke (g),with built in

socket feature, over nut (h). Grip the yoke and turn to loosen nut, after the nut is

loosened hand turn until lid assembly can be removed from gun. When replacing

lid assembly to gun assembly, hand tighten nut (h) and then slide yoke (g) over

nut (h) to tighten securely.

IMPORTANT: Do not immerse the gun in solvent, this will cause damage to

the packings.

NOTE: Always comply with local codes when disposing of solvents.

5. Remove air cap and immerse in a suitable solvent. Use a bristle brush to

clean dried paint and blow it dry with compressed air.

6. Use cleaning tool (supplied) to clean small clogged holes.

7. Wipe gun with a solvent soaked cloth.

IMPORTANT: Make certain air cap and fluid nozzle are kept clean at all

times. DO NOT use hard objects to clean clogged holes. The smallest

amount of damage may cause irregular spray pattern.

Lubrication

Lubrication procedures must be observed after thoroughly cleaning the gun to

ensure effective, high quality performance of spray gun.

1. Lubricate working points with straight mineral oil, or castor oil.

2. Periodically, place a few drops of oil on tapered sections of fluid nozzle to

ensure easy operation of air cap. When spraying water base materials, coat

fluid nozzle inside and outside with straight mineral oil after each use.

MAINTENANCE

7- ENG D25867

8- ENG

D25867

Dried material

is clogging

side-port “A”

and causing

side-port “B” to

blow spray

towards the

clogged side

A. Soak side-ports in

thinner to clean clog.

DO NOT poke any

opening with hard

objects.

B. Dried material at

fluid nozzle “C”

restricts air flow

Loose air nozzle

Air pressure set

too high

Remove air nozzle.

Wipe off fluid tip using a

cloth soaked in thinner

or by soft brush

Fasten nozzle securely

Reduce air pressure

C. Spitting, irregular

or fluttering spray

Fluid nozzle cracked or worn

Leak at thread of fluid nozzle

Leak at fluid needle

Needle packing worn out

Insufficient fluid in cup

Vent hole in container cover

clogged

Tighten or replace

Tighten fluid nozzle

Tighten compression nut

assembly or replace

needle packing

Replace packing

Fill cup with fluid

Clean Out

D. Split spray pattern Air pressure too high Turn pattern control

knob clockwise to

decrease fan width.

Turn fluid needle

adjusting nut counter-

clockwise to increase

fluid flow

Material too heavy

Insufficient air pressure

Fluid pressure too high

Dried material on tip of fluid

nozzle or air jets of air cap

Thin material or use

larger orifice fluid nozzle

set

Increase pressure to

within limit

Reduce pressure

Clean

Air needle partially closed

Dried material in air jets or air

cap

Obstruction in air line

Remove obstruction

Reduce air pressure

and/or open fluid control

knob

Air pressure to high for

viscosity of fluid

Loose cup or foreign sub-

stances on/between cup

thread and fluid inlet

Tighten and clean or

replace it

F. Inadequate air de-

livery

E. Unatomized or

spattered spray

G. Excessive fog

I. Material leaking

from nozzle when

trigger is released

H. Material leaking

from fluid inlet of

cup.

Worn fluid needle

Dried material in tip of nozzle

Loose packing nut

Replace

Clean

Tighten needle packing

nut by turning

counterclockwise

Defective Pattern Likely Cause Suggested Remedy

TROUBLESHOOTING

Open control knob

Clean

10- SP

D25867

• CONSERVE ESTAS INSTRUCCIONES •

LA OPERACIÓN O EL MANTENIMIENTO INADECUADOS DE

ESTE PRODUCTO PODRÍAN DETERMINAR SERIAS LESIONES

Y DAÑOS A LA PROPIEDAD. LEA Y COMPRENDA TODAS LAS

ADVERTENCIAS E INSTRUCCIONES OPERATIVAS ANTES DE

UTILIZAR ESTE EQUIPO.

Pueden ocurrir las siguientes situaciones de peligro durante el uso normal

de este producto:

PELIGRO QUÉ PUEDE OCURRIR CÓMO PREVENIRLO

Cuando se rocía con pinturas o

materiales, ellas se fraccionan en

pequeñas partículas que se

mezclan con el aire. Ello origina

que ciertas pinturas y materiales

se tornen extremadamente

inflamables y puedan causar

serias lesiones o la muerte.

Jamárocíe en las cercanías de

llama abierta o llamas piloto en

cocinas o calefactores.

Jamás fume mientras esté

rociando.

Al rociar en interiores,

suministre amplia ventilación.

RIESGO DE

EXPLOSIÓN O

INCENDIO -

MATERIALES

INFLAMABLES

NORMAS DE SEGURIDAD - DEFINICIONES

Indica una situación de

peligro inminente que,

si no es evitada, podrácausar

la muerte o serias lesiones.

Indica una

situación potencialmente riesgosa que, si

no es evitada, podría ocasionar la muerte

o lesiones serias.

Indica una situación

potencial de riesgo,

que, si no es evitada, puede causar

lesiones menores o moderadas.

Utilizada sin el símbolo

de alerta de seguridad,

indica una situación potencialmente

riesgosa que, si no es evitada, puede

ocasionar daños a la propiedad.

SEGURIDAD y PREVENCIÓN DE PROBLEMAS AL EQUIPO. Para ayudarlo a identificar esta información

hemos utilizado los símbolos que se indican más abajo. Sírvase leer el manual y prestar atención a dichas

secciones.

Este manual contiene información que resulta importante para que usted conozca y comprenda. Esta

información se relaciona con la protección de SU SEGURIDAD y LA PREVENCIÓN DE

PROBLEMAS A SU EQUIPO. Para ayudarlo a identificar esta información hemos utilizado los

símbolos que se indican más abajo. Sírvase leer el manual y prestar atención a dichas secciones.

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

11- SP D25867

ESPECIFICACIONES

Entrada de aire 1/4 NPT

Máxima presión de aire 100 psi.

Recomendado para operar el aire a presión 60 psi.

RIESGO DE

EXPLOSIÓN -

MATERIALES

INCOMPATIBLES

PELIGRO QUÉ PUEDE OCURRIR CÓMO PREVENIRLO

Solventes del tipo 1, 1, 1 -

Tricloroetano y Cloruro de

metileno, pueden reaccionar

químicamente con el aluminio

utilizado en la mayoría de los

equipos de rociado, esta pistola y

su copa, produciendo una

explosión que podría determinar

serias lesiones o la muerte.

Lea la etiqueta o la hoja de

especificaciones del material

que usted intenta rociar.

1.Jamás use tipo alguno de

material que contenga esos

solventes.

2.Jamás use esos solventes

para la limpieza del equipo o su

enjuagado.

3.En caso de dudas respecto a

la compatibilidad del material,

contacte a su proveedor de

materiales.

Algunas pinturas, recubrimientos y

solventes pueden causar daños

pulmonares y quemaduras, si son

inhalados o permitidos que tomen

contacto con la piel o los ojos.

Utilice una máscara aprobada

NIOSH o un respirador y ropa

protectora diseñada para ser usada

con su aplicación específica y

materiales de rociado. Algunas

máscaras solo proveen una

protección limitada contra

materiales tóxicos y solventes

dañinos de pinturas. En caso de

incertidumbre acerca de su equipo

o materiales, consulte con un

experto en seguridad o un

higienista industrial.

RIESGO DE

INHALACIÓN

RIESGO DE

OBJETOS

ARROJADOS

Ciertas partes se encuentran

sometidas a presión, cuando la

pistola estáconectada a una

tubería de aire comprimido. Esas

partes podrían ser expulsadas si la

pistola fuese desarmada.

El aire comprimido puede arrojar

suciedad, partículas de metal, etc

y posiblemente ocasionar

lesiones.

La exposición prolongada al

rociado de aire puede ocasionar

daños permanentes de audición.

Desconecte la pistola de la

cañería de aire, o despresurice

completamente la misma, cada

vez que la pistola deba ser

desarmada.

Jamás apunte ninguna boquilla

o rociador hacia persona alguna

o parte del cuerpo.

Al rociar, use siempre antiparras

de seguridad ANSI 278.1

aprobadas.

Al operar equipo de rociado,

use siempre protección

auditiva.

Andere Handbücher für 919.155350

Inhaltsverzeichnis

Sprachen:

Andere Craftsman Spritzpistole Handbücher

Craftsman

Craftsman 486.24533 Bedienungsanleitung

Craftsman

Craftsman 486.245333 Bedienungsanleitung

Craftsman

Craftsman 919.716171 Bedienungsanleitung

Craftsman

Craftsman 486.245313 Bedienungsanleitung

Craftsman

Craftsman 315.SS630 Bedienungsanleitung

Craftsman

Craftsman CMXCAFG190682 Bedienungsanleitung

Craftsman

Craftsman 486.245313 Bedienungsanleitung

Craftsman

Craftsman 919.155150 Bedienungsanleitung

Craftsman

Craftsman 486.245341 Bedienungsanleitung

Craftsman

Craftsman 24531 - Tow-Behind Sprayer Bedienungsanleitung

Craftsman

Craftsman 757.24525 Bedienungsanleitung

Craftsman

Craftsman 315.SS630 Bedienungsanleitung

Craftsman

Craftsman 786.15160 Bedienungsanleitung

Craftsman

Craftsman 919.716100 Bedienungsanleitung

Craftsman

Craftsman 919.716051 Bedienungsanleitung

Craftsman

Craftsman 486.245312 Bedienungsanleitung

Craftsman

Craftsman 919.15519 Bedienungsanleitung

Craftsman

Craftsman 919.1551 Bedienungsanleitung

Craftsman

Craftsman 486.245332 Bedienungsanleitung

Craftsman

Craftsman 919.155310 Bedienungsanleitung

Craftsman

Craftsman SKID SPRAYER 486.24534 Bedienungsanleitung

Craftsman

Craftsman 486.245332 Bedienungsanleitung

Craftsman

Craftsman 919.155190 Bedienungsanleitung

Craftsman

Craftsman 919.150020 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

Graco

Graco HydroShield WMBH00 Stücklistenhandbuch

WAGNER

WAGNER W 125 Bedienungsanleitung