Craftsman 137.21239 Bedienungsanleitung

Operator’s Manual

12 in. SLIDING COMPOUND

MITER SAW WITH LASER TRAC®

Model No. 137.212390

CAUTION:

Before using this Miter Saw,

read this manual and follow

all its Safety Rules and

Operating Instructions

ϥSafety Instructions

ϥInstallation

ϥOperation

ϥMaintenance

ϥParts List

Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA

Visit our Craftsman website: www.sears.com/craftsman

Part No. 137212390001 Printed in China

Customer Help Line

For Technical Support

1-800-843-1682

Sears Parts &

Repair Center

1-800-488-1222

33.9

TABLE OF CONTENTS

SECTION PAGE

Warranty ............................................................................................... 2

Product Speciﬁcations .......................................................................... 3

Symbols................................................................................................. 4

Power Tool Safety ................................................................................ 5

Compound Miter Saw Safety ................................................................ 8

Electrical Requirements and Safety ...................................................... 9

Accessories and Attachments ............................................................... 12

Tools Needed for Assembly .................................................................. 13

Carton Contents ................................................................................... 14

Know Your Compound Miter Saw ........................................................ 15

Glossary of Terms ................................................................................ 16

Assembly and Adjustments .................................................................. 18

Operation .............................................................................................. 28

Maintenance ......................................................................................... 40

Troubleshooting Guide ......................................................................... 42

Parts List ............................................................................................... 44

WARNING

To avoid electrical hazards, ﬁre hazards or damage to the tool, use proper

circuit protection.

This tool is wired at the factory for 110-120 Volt operation. It must be

connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.

To avoid shock or ﬁre, replace power cord immediately if it is worn, cut or

damaged in any way.

Before using your tool, it is critical that you read and understand these

safety rules. Failure to follow these rules could result in serious injury to

you or damage to the tool.

WARNING

Some dust created by using power tools contains chemicals known to the state

of California to cause cancer and birth defects or other reproductive harm.

Some examples of these chemicals are:

●Lead from lead-based paints

●Crystalline silica from bricks, cement and other masonry

products

●Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do

this type of work. To reduce your exposure to these chemicals, work in a

well ventilated area and work with approved safety equipment such as dust

masks that are specially designed to ﬁlter out microscopic particles.

WARRANTY

PRODUCT SPECIFICATIONS

MOTOR

Power Source ............................................................. 120V AC, 60Hz, 15 Amp

Speed ......................................................................... 4200 RPM (No load)

Brake .......................................................................... Electric

Double Insulated.......................................................... Yes

Motor Arbor Shaft Size................................................. 5/8 in.

BLADE SIZE

Diameter...................................................................... 12 in.

Arbor size.................................................................... 1 in. w/a 5/8 in. reducer

Rotating Table:

Diameter...................................................................... 11-13/16 in.

Miter Detent Stops ...................................................... 0, 15, 22.5, 31.6, 45º R & L

Bevel Positive Stops.................................................... 0, 33.9, 45ºL

Cutting Capacity:

Crosscut....................................................................... 4 in. x 12-1/4 in.

Miter 45° R & L............................................................ 4 in. x 8-3/4 in. R & L

Bevel 45ºL................................................................... 2-1/2 in. x 12-1/4 in. L

45° Miter and 45° Bevel .............................................. 2-1/2 in. x 8-3/4 in.

2007/12

CRAFTSMAN ONE YEAR FULL WARRANTY

If this Craftsman tool fails due to a defect in material or workmanship within

one year from the date of purchase, call 1-800-4-MY-HOME Rto arrange for

free repair (or replacement if repair proves impossible).

This warranty applies for only 90 days from the date of purchase if this product

is ever used for commercial or rental purposes.

This warranty does not include expendable parts, such as lamps, batteries,

bits or blades.

This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

WARNING ICONS

Your power tool and its Owner’s Manual may contain “WARNING ICONS”

(a picture symbol intended to alert you to, and/or instruct you how to avoid,

a potentially hazardous condition). Understanding and heeding these

symbols will help you operate your tool better and safer. Shown below are

some of the symbols you may see.

SAFETY ALERT: Precautions that involve your safety.

PROHIBITION

WEAR EYE PROTECTION: Always wear safety goggles or safety

glasses with side shields.

READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce

the risk of injury, user and all bystanders must read and understand

instruction manual before using this product.

SUPPORT AND CLAMP WORK

KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away

from the blade will result in serious personal injury.

DANGER



WARNING



CAUTION



CAUTION

DANGER: indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

CAUTION: used without the safety alert symbol indicates

a potentially hazardous situation which, if not avoided,

may result in property damage.

SYMBOLS

POWER TOOL SAFETY

GENERAL SAFETY INSTRUCTIONS

BEFORE USING THIS POWER TOOL

Safety is a combination of common

sense, staying alert and knowing how

to use your power tool.

CAUTION

To avoid mistakes that could cause

serious injury, do not plug the tool in

until you have read and understood

the following.

1. READ and become familiar

with the entire Operator’s

Manual. LEARN the tool’s

application, limitations and

possible hazards.

2. KEEP GUARDS IN PLACE and in

working order.

3. REMOVE ADJUSTING KEYS

AND WRENCHES. Form the habit

of checking to see that keys and

adjusting wrenches are removed

from the tool before turning ON.

4. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite

accidents.

5. DO NOT USE IN DANGEROUS

ENVIRONMENTS. Do not use

power tools in damp locations, or

expose them to rain or snow. Keep

work area well lit.

6. KEEP CHILDREN AWAY. All

visitors and bystanders should be

kept a safe distance from work area.

7. MAKE WORKSHOP CHILD PROOF

with padlocks, master switches or by

removing starter keys.

8. DO NOT FORCE THE TOOL. It will

do the job better and safer at the

rate for which it was designed.

9. USE THE RIGHT TOOL. Do not

force the tool or an attachment to do

a job for which it was not designed.

10.USE PROPER EXTENSION

CORDS. Make sure your extension

cord is in good condition. When

using an extension cord, be sure to

use one heavy enough to carry the

current your product will draw. An

undersized cord will result in a drop

in line voltage and in loss of power

which will cause the tool to overheat.

The table on page 11 shows the

correct size to use depending on

cord length and nameplate ampere

rating. If in doubt, use the next

heavier gauge. The smaller the

gauge number, the heavier the cord.

11.WEAR PROPER APPAREL. Do

not wear loose clothing, gloves,

neckties, rings, bracelets or other

jewelry which may get caught in

moving parts. Nonslip footwear is

recommended. Wear protective hair

covering to contain long hair.

12.ALWAYS WEAR EYE

PROTECTION. Any power

tool can throw foreign

objects into the eyes and

could cause permanent

eye damage. ALWAYS wear Safety

Goggles (not glasses) that comply

with ANSI Safety standard Z87.1.

Everyday eyeglasses have only

impact–resistant lenses. They

ARE NOT safety glasses. Safety

Goggles are available at Sears.

NOTE: Glasses or goggles not in

compliance with ANSI Z87.1 could

seriously injure you when they break.

13.WEAR A FACE MASK OR DUST

MASK. Sawing operation produces

dust.

14.SECURE WORK. Use clamps or

a vise to hold work when

practical. It is safer than

using your hand and

it frees both hands to

operate the tool.

15.DISCONNECT TOOLS FROM

POWER SOURCE before servicing,

and when changing accessories

such as blades, bits and cutters.

16.REDUCE THE RISK OF

UNINTENTIONAL STARTING.

Make sure switch is in the OFF

position before plugging the tool in.

POWER TOOL SAFETY

17.USE RECOMMENDED

ACCESSORIES. Consult

this Operator’s Manual for

recommended accessories. The use

of improper accessories may cause

risk of injury to yourself or others.

18.NEVER STAND ON THE TOOL.

Serious injury could occur if the

tool is tipped or if the cutting tool is

unintentionally contacted.

19.CHECK FOR DAMAGED PARTS.

Before further use of the tool, a

guard or other part that is damaged

should be carefully checked to

determine that it will operate

properly and perform its intended

function – check for alignment of

moving parts, binding of moving

parts, breakage of parts, mounting

and any other conditions that may

affect its operation. A guard or other

part that is damaged should be

properly repaired or replaced.

20. NEVER LEAVE THE TOOL

RUNNING UNATTENDED. TURN

THE POWER “OFF”. Do not walk

away from a running tool until the

blade comes to a complete stop

and the tool is unplugged from the

power source.

21.DO NOT OVERREACH. Keep

proper footing and balance at all

times.

22. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for best

and safest performance. Follow

instructions for lubricating and

changing accessories.

23. WARNING: Dust generated from

certain materials can be hazardous

to your health. Always operate saw

in well-ventilated area and provide

for proper dust removal.

24.

People

with electronic devices, such as

pacemakers, should consult their

physician(s) before using this

product. Operation of electrical

equipment in close proximity to

a heart pacemaker could cause

interference or failure of the

pacemaker.

POWER TOOL SAFETY

DANGER



SPECIFIC SAFETY INSTRUCTIONS

FOR THIS COMPOUND MITER SAW

1. DO NOT operate the miter saw

until it is completely assembled

and installed according to these

instructions.

2. IF YOU ARE NOT thoroughly

familiar with the operation of miter

saws, seek guidance from your

supervisor, instructor or other

qualiﬁed person.

3. ALWAYS hold the work ﬁrmly

against the fence and table.

DO NOT perform any operation

free hand (use clamp wherever

possible).

4. KEEP HANDS out of the path of the

saw blade. If the workpiece you are

cutting would cause your hands to

be within 8-3/4 in. of the saw blade,

the workpiece should be clamped in

place before making the cut.

5. BE SURE the blade is sharp, runs

freely and is free of vibration.

6. ALLOW the motor to come up to full

speed before starting a cut.

7. KEEP THE MOTOR AIR SLOTS

CLEAN and free of chips or dust.

8. ALWAYS MAKE SURE all handles

are tight before cutting, even if the

table is positioned in one of the

positive stops.

9. BE SURE both the blade and the

collar are clean and the arbor bolt is

tightened securely.

10.USE only blade collars speciﬁed for

your saw.

11.NEVER use blades larger in

diameter than 12 inches.

12.NEVER apply lubricants to the

blade when it is running.

13.ALWAYS check the blade for

cracks or damage before operation.

Replace a cracked or damaged

blade immediately.

14.NEVER use blades recommended

for operation at less than 4200

RPM.

15.ALWAYS keep the blade guards in

place and use at all times.

16.NEVER reach around the saw

blade.

17.MAKE SURE the blade is not

contacting the workpiece before the

switch is turned ON.

18.IMPORTANT: After completing the

cut, release the trigger and wait for

the blade to stop before returning

the saw to the raised position.

19.MAKE SURE the blade has come

to a complete stop before removing

or securing the workpiece, changing

the workpiece angle or changing the

angle of the blade.

20. NEVER cut metals or masonry

products with this tool. This miter

saw is designed for use on wood

and wood-like products.

COMPOUND MITER SAW SAFETY

21.NEVER cut small pieces. If the

workpiece being cut would cause

your hand or ﬁngers to be within

8-3/4 in. of the saw blade the

workpiece is too small.

22.PROVIDE adequate support to the

sides of the saw table for long work

pieces.

23.NEVER use the miter saw in an

area with ﬂammable liquids or

gases.

24.NEVER use solvents to clean plastic

parts. Solvents could possibly

dissolve or otherwise damage the

material.

25.SHUT OFF the power before

servicing or adjusting the tool.

26.DISCONNECT the saw from

the power source and clean the

machine when ﬁnished using.

27.MAKE SURE the work area is clean

before leaving the machine.

28.SHOULD any part of your miter saw

be missing, damaged, or fail in any

way, or any electrical component

fail to perform properly, lock the

switch and remove the plug from

the power supply outlet. Replace

missing, damaged, or failed parts

before resuming operation.

POWER SUPPLY AND MOTOR

SPECIFICATIONS

The AC motor used in this saw is

a universal, nonreversible type.

See “MOTOR” in the “PRODUCT

SPECIFICATIONS” section on page 2.

To avoid electrical hazards, ﬁre

hazards, or damage to the tool,

use proper circuit protection. Your

saw is wired at the factory for 120

V operation. Connect to a 120 V, 15

A circuit and use a 15 A time delay

fuse or circuit breaker. To avoid

shock or ﬁre, if power cord is worn

or cut, or damaged in any way, have

it replaced immediately.

ELECTRICAL REQUIREMENTS

WARNING

ELECTRICAL REQUIREMENTS –

cont’d

DOUBLE INSULATED

The power tool is double insulated to

provide a double thickness of insulation

between you and tool’s electrical

system. All exposed metal parts are

isolated from the internal metal motor

components with protecting insulation.

Replacement parts – When servicing,

use only identical replacement parts.

Polarized plugs – This saw has a plug

that looks like the one shown below:

To reduce the risk of electrical shock,

this saw has a polarized plug (one

blade is wider than the other). This plug

will ﬁt in a polarized outlet only one

way. If the plug does not ﬁt fully in the

outlet, reverse the plug. If it still does

not ﬁt, contact a qualiﬁed electrician to

install the proper outlet. Do not change

the plug in any way.

Double insulation does not take the

place of normal safety precautions

when operating this tool.

To avoid electrocution:

1. Use only identical replacement parts

when servicing a tool with double

insulation. Servicing should be

performed by a qualiﬁed technician.

2. Do not use power tools in wet or

damp locations or expose them to

rain or snow.

MOTOR SAFETY PROTECTION

IMPORTANT

To avoid motor damage, the motor

should be blown out or vacuumed

frequently to keep sawdust from

interfering with the motor ventilation.

1. Connect this saw to a 120 V circuit.

This circuit must not be less than a

#12 wire with a 20 A time lag fuse or

a #14 wire with a 15 A time lag fuse.

NOTE: When using an extension

cord on a circuit with a #14 wire, the

extension cord must not exceed 25

feet in length.

2. If the motor will not start, release the

trigger switch immediately. UNPLUG

THE SAW. Check the saw blade to

make sure it turns freely. If the blade

is free, try to start the saw again. If

the motor still does not start, refer to

the TROUBLESHOOTING GUIDE.

3. If the tool suddenly stalls while

cutting wood, release the trigger

switch, unplug the tool and free the

blade from the wood. The saw may

now be started and the cut ﬁnished.

4. FUSES may “blow” or circuit

breakers may trip frequently if:

a. MOTOR is overloaded –

overloading can occur if you feed

WARNING

ELECTRICAL REQUIREMENTS AND SAFETY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Gesehen Handbücher

Craftsman

Craftsman 113.24261 Datenblatt

Craftsman

Craftsman 113.298051 Bedienungsanleitung

Craftsman

Craftsman MiterMate 137.212260 Bedienungsanleitung

Craftsman

Craftsman 113.234701 Bedienungsanleitung

Craftsman

Craftsman 315.271290 Bedienungsanleitung

Craftsman

Craftsman 124.32607 Bedienungsanleitung

Craftsman

Craftsman 315.212100 Bedienungsanleitung

Craftsman

Craftsman 113.24181 Bedienungsanleitung

Craftsman

Craftsman 901.23181 Bedienungsanleitung

Craftsman

Craftsman Accra-Arm 113.29440 Datenblatt

Craftsman

Craftsman 315.115740 Bedienungsanleitung

Craftsman

Craftsman 113.298340 Bedienungsanleitung

Craftsman

Craftsman 113.197511 Bedienungsanleitung

Craftsman

Craftsman 172.26043 Bedienungsanleitung

Craftsman

Craftsman 137.375630 Bedienungsanleitung

Craftsman

Craftsman 103.0213 Bedienungsanleitung

Craftsman

Craftsman 113.298760 Bedienungsanleitung

Craftsman

Craftsman 315.108240 Bedienungsanleitung

Craftsman

Craftsman 137.415030 Bedienungsanleitung

Craftsman

Craftsman 320.28191 Bedienungsanleitung

Craftsman

Craftsman TABLE SAW 315.22831 Bedienungsanleitung

Craftsman

Craftsman Craftsman 172.10855 12 Amp Bedienungsanleitung

Craftsman

Craftsman 137.212920 Bedienungsanleitung

Craftsman

Craftsman CMCS350 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung