Crane Duo-Chek Bedienungsanleitung
brands you trust.
Duo-Chek®Check Valves
Installation and Operation Manual
www.cranecpe.com
Duo-Chek® Check Valves
www.authorizedparts.com
www.authorizedparts.com
Please read the warning and caution
statements on pg 2 prior to installation.
2 www.cranecpe.com
Index
Installation and Maintenance Page 3
Assembly Page 4
Parts Page 5
WARNING
Proper installation plays an important role in valves performance. Installation must be performed
-
result in damage to the valve.
!
CAUTION
READ INSTRUCTIONS BEFORE INSTALLATION or valve service. Failure to follow instructions could
result in death or serious injury. If there is any question, contact the factory at 936-271-6500.
!
www.authorizedparts.com
www.authorizedparts.com
3
www.cranecpe.com
Please read the warning and caution
statements on pg 2 prior to installation.
Installation & Maintenance
INSTALLATION
1. Remove the valve from carton or packing skid.
2. The protective rust proof coating on the internal parts of steel or cast iron valves should be re-
moved by brushing out with any standard petroleum solvent (Varsol, Kerosene), and air dry. Insure
internal parts operate freely.
3. Stainless Steel or Bronze valves need only to be wiped clean and installed.
4. In horizontal ow installation, the hinge pin must be vertical.
5. Insert the valve between two companion anges of the same series as the valve and place gaskets
on ange faces. The arrow on the valve or name plate indicating direction of ow should coincide
with line ow. Install studs through companion anges and tighten, using standard industry prac-
tice.
6. In liquid service we recommend valve be installed at least ve (5) pipe diameters downstream
from a pump discharge and/or other pipe ttings for maximum service life. Consult factory.
MAINTENANCE
Make sure the valve is not under pressure before starting any maintenance.
Disassembly** (Refer to assembly drawing on next page.)
1. Lay valve down with the downstream side of the valve upward.
2. Remove stop pin retainers (6) and hinge pin retainers (7).
3. Remove stop pin (3), being careful with the short hooked spring legs on valves 6”and larger.
4. Remove hinge pin (4) out of the body (1) while holding spring(s) rmly as some are preloaded and
may snap out. Observe caution.
5. Remove springs (5), plates (2), and bearings (8), (9), and (10).
CAUTION
!
www.authorizedparts.com
www.authorizedparts.com
4www.cranecpe.com Please read the warning and caution
statements on pg 2 prior to installation.
Assembly
ASSEMBLY**
1. Lay body down with downstream side of valve upward.
2. Clean all parts in a suitable solvent.
3. Position both plates (2) in body (1) with hinge lugs together and align with pin holes. If valve is equip-
ped with support sleeves (11), assemble into plate with body bearings (9).
4. Lay springs (5) in plate (2) recess, between lugs, with short hooked leg extending upward on valves
6” and larger (other longer leg to contact plate). On smaller valves, spring(s) (5) without short leg, wind
spring legs 180 , install with legs contacting each plate and hold to insert hinge pin (4) in step 6.
5. Insert all bearings provided, (8), (9) and (10).
6. Insert hinge pin (4) through plate lugs (2), bearings, (8), (9), (10), and through spring coils (5).
7. Pull stop pin leg of spring (short hooked leg) toward plate leg and insert stop pin (3). Repeat until
stop pin is fully inserted in body holes.
8. Install hinge pin retainers (7) and stop pin retainers (6) using PTFE tape or a suitable thread seal- ing
compound.
** No Special tools are required.
www.authorizedparts.com
www.authorizedparts.com
5
www.cranecpe.com
Please read the warning and caution
statements on pg 2 prior to installation.
Duo-Chek Parts
Item
Number No. Req'd Description
1 1 Body
2 2 Plate
3 1 Stop Pin
41Hinge Pin
5 2* Spring
6 2 Stop Pin Retainer
72Hinge Pin Retainer
84** Plate Lug Bearing
94** Body Lug Bearing
10 3* Spring Bearing
11+ 2Support Sleeve
10*
10
1
3
6
7
4
8
11
9
5*
5
2
* Some valves require 4 springs & 5 spring bearings
** These quantities may vary according to the valve size
+ Not required on valves smaller than 24"
www.authorizedparts.com
www.authorizedparts.com
Crane ChemPharma & Energy
9860 Johnson Road
Montgomery, TX USA 77316
Tel: +1 936 588 4447
Fax: +1 936 588 4427
www.cranecpe.com
Crane Co., and its subsidiaries cannot accept responsibility for possible errors in catalogues, brochures, other printed materials, and website
information. Crane Co. reserves the right to alter its products without notice, including products already on order provided that such al-
teration can be made without changes being necessary in specications already agreed. All trademarks in this material are property of the
Crane Co. or its subsidiaries. The Crane and Crane brands logotype, in alphabetical order, (ALOYCO®, CENTER LINE®, COMPAC-NOZ®, CRANE®,
DEPA®, DUO-CHEK®, ELRO®, FLOWSEAL®, JENKINS®, KROMBACH®, NOZ-CHEK®, PACIFIC VALVES®, RESISTOFLEX®, REVO®, SAUNDERS®, STOCK-
HAM®, TRIANGLE®, UNI-CHEK®, WTA®, and XOMOX®) are registered trademarks of Crane Co. All rights reserved.
©2014 Crane ChemPharma & Energy, www.cranecpe.com
brands you trust.
CPE-DUO-CHEK-CV-IOM-EN-LT-8-2014-19
®
®
www.authorizedparts.com
www.authorizedparts.com
Inhaltsverzeichnis
Andere Crane Steuereinheit Handbücher
Crane
Crane CPV36M Series Bedienungsanleitung
Crane
Crane KROMBACH 510 Handbuch
Crane
Crane Dominator PRO Z4000 Series Montageanleitung
Crane
Crane D923 Bedienungsanleitung
Crane
Crane D1088 Handbuch
Crane
Crane NOZ-CHEK Cryogenic Handbuch
Crane
Crane Dominator 80mm Series Handbuch
Crane
Crane D2003 Montageanleitung
Crane
Crane DM921 Gebrauchsanweisung
Crane
Crane Class 150 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
