Crestron PC-100 Maßzeichnung
DO GUIDE
PC-100
8-Outlet Power Conditioner and Surge Protector
DO Install the Device
The Crestron®PC-100 is designed to be rack mounted. It occupies 1U of rack space. Using a #1 or
#2 Phillips screwdriver, attach the two included rack ears to the device, and then mount the device
into the rack using four mounting screws (not included).
DO Connect the Device
Make connections to the PC-100 using Crestron power supplies for Crestron equipment.
CAUTION: The PC-100 must be plugged into a circuit that has a 20-amp circuit breaker.
Front Panel Connections
DO Check the Box
QTY PRODUCT COLOR PART NUM.
2Bracket, Rack Ear, 1U 2032122
1Connector, 2-Pin 2003574
SWITCHED ON 1 and 2:
Switched ac outputs
DELAYED ON 1 and 2:
Switched ac outputs
Ground
PROTECTION:
To alarm, light, or
logic input of a device
Rear Panel Connections
NOTE: The front panel outlet is always on, independent of the front panel switch position. It is
protected from surges and has EMI ltering. However, if the unit is out of voltage range (93 to
135 volts), has incorrect wiring, or has failed surge protection, all eight rear panel outlets turn
off, but the front outlet remains on. If this occurs, the yellow SHUTDOWN LED lights and the
PWR LED turns yellow.
NOTE: The rear panel outlets marked “SWITCHED ON” turn on immediately when the front
panel switch is turned on (moved to the up position). The outlets marked “DELAYED ON 1” turn
on one second after the front panel switch is turned on. The outlets marked “DELAYED ON 2”
turn on two seconds after the front panel switch is turned on.
NOTE: The 2-pin PROTECTION port on the rear panel is an isolated contact and has the pins
internally opened while all surge protection is active. The connection is closed when any surge
protection is compromised. This provides surge protection notication to a connected control
system.
NOTE: The front panel LEDs behave as follows:
LED COLOR FUNCTIONALITY
PWR Amber/Green Amber: Power is present on ac cord.
Green: Switch is in ON position, and power is present.
FAULT Red
One of the following is true:
- Surge protection is compromised.
- No ground is detected.
- Line and neutral are reversed.
PROTECTION Green All surge protection is functional.
SHUTDOWN Amber/Green An over- or undervoltage condition is causing the
outputs to turn off.
ALWAYS ON:
Unswitched ac output
DO GUIDE DOC. 7694E (2043850) 09.16
Specications subject to change without notice.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
This product is Listed to applicable UL Standards and requirements by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables
par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Rack Mounting Safety Precautions
Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient temperature. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient temperature
(Tma) specied by the manufacturer.
Reduced Airow: Installation of the equipment in a rack should be such that the
amount of airow required for safe operation of the equipment is not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might
have on overcurrent protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Earthing: Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g., use of power strips).
The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty
can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Crestron Fusion are either trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
Versiport
Power
Ethernet
Color Key
Display
PC-100 CEN-SWPOE-16
PRO-3
CCS-UC-CODEC-200
Andere Crestron Wechselstromverteilung Handbücher
