Crestron FT2-700-ELEC Series Bedienungsanleitung

The Crestron® FT2-700-ELEC and the FT2-700-ELEC-PTL FlipTop™ cable

management systems install into a table or other horizontal surface to

provide modular tabletop connectivity for users. The FT2-700-ELEC

series feature a one touch lid that retracts fully and disappears with the

tap of a button. When the lid is retracted, 12 module slots are arranged in

two rows of six. The flexible modular design may also be customized with

an assortment of Crestron accessories. For more information about the

accessories, please visit www.crestron.com/Crestron-FlipTops.

The FT2-700-ELEC Series features a built in electrical power bus, which

enables compatibility with one-touch cable retractors, active connector

plates, and USB rapid charging modules. It also enables backlighting of

the symbol icons on all retractors, connector plates, and USB charging

modules.

The FT2-700-ELEC-PTL offers an alternative pass-through lid style

which allows cables to be fully extended while the lid is closed.

The FT2-700-ELEC and the FT2-700-ELEC-PTL are functionally similar.

For simplicity within this document, they are both referred to as the

"FT2-700 assembly."

In the Box

1 FT2-700-ELEC, FlipTop™ FT2 Series, 700 Size, Electrical

Additional Items

3 Bars, Locking, with Screws (P/N 4528906)

1 Cable, DC Power Splitter (P/N 2050094)

1 Holder, Power Supply (P/N 2048887)

4 Module, Blank Plate (P/N 2049602)

8 Module, Pass-Through Cable (P/N 4526880)

1 Power Cord, 5 ft 10 in. (1.78 m) (P/N 2042043)

1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (P/N 2045873)

4 Spacer, Plastic, FT2-700 (P/N 2050568)

1 Template, Cutout (P/N 4527491)

FT2-700-ELEC-AL Only

1 Bezel, FT2-700, Alloy (P/N 4529321)

FT2-700-ELEC-PTL-AL Only

1 Bezel, FT2-700, Pass-Through Lid, Alloy (P/N 4531563)

FT2-700-ELEC-PTL-B Only

1 Bezel, FT2-700, Pass-Through Lid, Black (P/N 4531562)

FT2-700-ELEC-B Only

1 Bezel, FT2-700, Black (P/N 4529320)

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Mount the FlipTop Assembly

A mounting hole is required for an FT2-700-ELEC installation. Use the

included template to cut a new mounting hole for new installations. The

FT2-700-ELEC may also replace an FT-600 FlipTop and use the existing

mounting. When determining the location for the FT2-700 assembly,

consider where users will be seated and their proximity to the FT2-700

assembly's modules and retractors. Refer to the FT2A-CBLR-1T and

FT2A-CBLR-GR series cable retractors for above-the-table cable pull-out

lengths.

For a new mounting, follow sections Cut the Mounting Hole and Secure

the FlipTop Assembly. To use the mounting hole of an existing FT-600

FlipTop assembly, follow sections Replace the FT-600 FlipTop Assembly

and Secure the FlipTop Assembly.

Cut the Mounting Hole

A saw, tracing utensil, and the included cutout template are required to

cut the mounting hole.

1. Check the table surface and the area beneath the table. Clear any

obstructions that may impede the installation or functionality of the

FT2-700 assembly, retractors, and accessories.

2. Using the included cutout template, trace an outline of the mounting

hole onto the table.

3. Cut the mounting hole in the table with an appropriate saw.

Replace the FT-600 FlipTop Assembly

An FT2-700 assembly may replace an FT-600 FlipTop assembly and use

the existing mounting hole. The FT-600 FlipTop assembly mounting hole is

larger than the mounting hole required for the FT2-700 assembly. The

included plastic spacers are used to help fill the gap between the mounting

hole and the FT2-700 assembly.

1. Loosen the four socket screws that secure the two mounting plates

and the FT-600 FlipTop assembly to the surface.

2. Remove the FT-600 FlipTop assembly.

3. Attach the four plastic spacers (included) to each corner of the

FT2-700 assembly.

4. Continue to prepare the FT2-700 assembly by attaching the DC power

splitter. Refer to Secure the FlipTop Assembly.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Secure the FlipTop Assembly

To prepare the FT2-700 assembly and secure it to the table surface:

1. Locate the included DC power splitter cable.

2. On the underside of the FT2-700 assembly, locate the power bus and

connect the dual-connector ends of the DC power splitter to the two

barrel jacks of the power bus. The cable will be accessed later in

Connect and Place the Power Supply.

3. Ensure that all four swiveling dogs are tucked inside of the FT2-700

assembly, and then insert the FT2-700 assembly into the mounting

hole until the top lip is flush with the table surface.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

4. Carefully tighten the four swiveling dogs in each corner of the FlipTop

assembly clockwise until the FT2-700 assembly is secured in place

against the table. Do not overtighten the swiveling dogs.

CAUTION: A manual torque screwdriver may be used to hand

tighten the swiveling dogs. Set the torque screwdriver to its lowest

setting to avoid stripping the swiveling dogs and damaging the

table. If removing the FT2-700 assembly from the table, ensure

that the screwdriver rotation is set correctly before loosening the

swiveling dogs.

Connect and Place the Power Supply

The FT2-700 assembly ships with one 24 VDC power supply that is used

to supply power to the power bus in the FT2-700 assembly. There are six

possible locations to attach the power supply. Connect the power supply

prior to installing any modules.

NOTE: Two power supplies are required if installing two rapid charging

modules in the FT2-700 assembly. For more information, refer to the

FT2A-CHGR-USBA-BASICQuick Start Guide (Doc.8423) or

FT2A-CHGR-USBA/CInstallation Guide (Doc.8219).

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

To connect the power supply to the power bus:

1. Underneath the FT2-700 assembly, connect the power supply to the

bottom of the power bus.

lIf connecting one power supply, connect the power supply’s power

cord to the single connector end of the DC power splitter cable.

Refer to step 1 in Secure the FlipTop Assembly.

lIf connecting two power supplies, connect each power supply’s

power cord to a barrel jack in the power bus.

2. Use the two included tie wraps to dress the power cord.

3. Slide the power supply into the power supply holder until it is secured in

place.

4. Align the four keyed tabs on the power supply holder with four keyed

slots on the FT2-700 assembly. Then, push the power supply holder up

and into the slots so that the keyed tabs engage the wide end of the

slots.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

5. Slide the holder downward until it is secured to the FT2-700 assembly.

6. Connect the included 5 ft 10 in. (1.78 m) power cord to the power jack

on top of the power supply.

7. Connect the other end of the power supply to a power source only

after all other modules have been installed and all connections have

been made to the FlipTop assembly.

Install the Modules

Installation procedures for most modules are available in separate

product documentation. For more information, refer to the specific

product manual located at www.crestron.com/manuals. The following

sections provide best practices and installation procedures for pass-

through cable modules and blank plate modules.

Position the Modules

The FT2-700 assembly includes FT2A-PLT-PT pass-through cable

modules and FT2A-PLT-BLANK blank plate modules.

Follow the best practices below when performing module installation.

lPerform module installation in the following order:

1. AC Power Outlet Modules (FT2A-PWR-US series)

2. Retractor modules (FT2A-CBLR-1T series and FT2A-CBLR-GR

series)

3. All other modules (FT2A-CP series, FT2A-CHGR series,

FT2A-PLT-PT, and FT2A-PLT-BLANK)

lPlace the FT2A-CBLR-GR modules only at the ends of a module row.

lDress all cables after installing each module.

Install the Pass-Through Cable Module

The FT2A-PLT-PT pass-through modules enable FT2-CBL-PT pass-

through cables and other types of interface cables to be installed within

the FT2-700 assembly. Each FT2A-PLT-PT cable module is packaged with

one nylon grommet and one cable plate. One empty module slot in the

FT2-700 assembly and one FT2-CBL-PT series or other interface cable

are required for installation.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Installing the Pass-Through Cable Module with 4K Cables

1. Push the connector end of the cable through the hole in the cable plate.

2. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector should sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the FT2-700 assembly lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

lThe grommet is not needed when installing most 4K cables. If

the cable is 10 mm or thinner, the grommet may be used.

3. Attach the side plate to the module by snapping the plastic clips on the

plate into the two slots on the module.

NOTE: If the side plate must be removed, use a small, flat object

(such as a flat-head screwdriver) to carefully pry the plastic clips on

the side plate off of the module near the two slots.

4. Feed the other end of the cable through an empty module slot in the

FT2-700 assembly.

5. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2-700

assembly.

Installing the Pass-Through Cable Module with Non-4K

Cables

The grommet is recommended to use with cables that are 10 mm or

thinner.

1. Open the grommet.

2. Insert a cable into the grommet with the connector facing up toward

the end user.

3. Press the grommet back together to secure the cable inside.

4. Push the grommet and cable through the hole in the cable plate.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

5. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector should sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the FT2-700 assembly lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

6. Attach the side plate to the module by snapping the plastic clips on the

plate into the two slots on the module.

NOTE: If the side plate must be removed, use a small, flat object

(such as a flat-head screwdriver) to carefully pry the plastic clips on

the side plate off of the module near the two slots.

7. Feed the other end of the cable through an empty module slot in the

FT2-700 assembly.

8. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2-700

assembly.

Install the Blank and Keystone Plate Module

Four blank plate modules are included to fill empty slots in module rows. A

keystone plate (sold separately) module allows for cables terminated with

standard keystone jacks to be installed in the FT2-700 assembly. The

blank and keystone modules each require one empty module slot for

installation.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Blank and Keystone Plate Modules

To install a blank or keystone plate module into the FT2-700 assembly:

lSlide the blank plate module down into the appropriate module slot.

Use the guide ribs on the front and rear of each module to help

position it in the FT2-700 assembly.

lFor the keystone plate module, complete the following steps.

1. Snap the cable’s keystone jack into the keystone opening in the

keystone plate module.

2. Feed the cable down through the empty module slot.

3. Slide the attached keystone plate module down into the same

module slot using the front and rear guide ribs to assist with

positioning.

Install the Locking Bars

1. Position the locking bars so that the screws attached to the locking

bars engage the screw holes in the FT2-700 assembly.

2. Using a manual torque screwdriver set to its lowest possible setting,

hand tighten the locking bar screws until the locking bars are secured

to the FT2-700 assembly.

CAUTION: Do not overtighten the locking bar screws.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Install the Bezel

Place the bezel onto the FT2-700 assembly so that the retractable lid fits

inside the bezel opening. The bezel is held in place using magnets.

Operate the FlipTop Assembly

To operate the FT2-700 assembly:

1. Tap the lid retraction button to retract the one-touch lid. The lid

disappears into the assembly.

2. Access the modules in the FT2-700 assembly.

3. Close the lid by lifting it vertically and returning it over the FlipTop

assembly.

FT2-700-ELEC Series QuickStart

FlipTop™ FT2 Series, 700 Size, Electrical

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Kabel und Steckverbinder Handbücher

Crestron

Crestron SR9600 Konfigurationshandbuch

Crestron

Crestron FlipTop FT2A-CBLR-1T Series Bedienungsanleitung

Crestron

Crestron FT2A-CP-USBA Bedienungsanleitung

Crestron

Crestron C2N-TXM-C50 Bedienungsanleitung

Crestron

Crestron TPS-CBL-S Bedienungsanleitung

Crestron

Crestron HZA-KEY1 Bedienungsanleitung

Crestron

Crestron TPS-CBL Bedienungsanleitung

Crestron

Crestron DigitalMedia Connectors DM-CONN-20 Betriebsanleitung

Crestron

Crestron Four-Way Amplified Splitter SRD-SPL-4 Bedienungsanleitung

Crestron

Crestron UC-B-ACCY Bedienungsanleitung

Crestron

Crestron FlipTop CBLR2 Series Bedienungsanleitung

Crestron

Crestron SmarTouch ST-112 Bedienungsanleitung

Crestron

Crestron FlipTop FT2 Series Bedienungsanleitung

Crestron

Crestron FT-PWR Anleitung zur Verwendung

Crestron

Crestron CBL-MULTI-HD-6 Bedienungsanleitung

Crestron

Crestron SP-CBL Bedienungsanleitung

Crestron

Crestron SmartPresenter SPC-121 Bedienungsanleitung

Crestron

Crestron FlipTop CBLR2 Series Maßzeichnung

Crestron

Crestron ST-CBL Bedienungs- und Montageanleitung

Crestron

Crestron ST-SPL Bedienungsanleitung

Crestron

Crestron FT2A-CP Series Bedienungsanleitung

Crestron

Crestron SR5500 Konfigurationshandbuch

Crestron

Crestron DM-8G-CONN-100 Bedienungsanleitung

Crestron

Crestron SmartPresenter SPC-122 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung