Crestron OnCue BPC-8 Betriebsanleitung

BPC(I)-8

onCue®Basic Presentation Controller

Supplemental Guide

Crestron Electronics, Inc.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, Crestron Toolbox, and onCue are either trademarks or registered trademarks of Crestron Electronics, Inc. in the

United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to

either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of

others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Supplemental Guide – DOC. 7100C Contents •i

Contents

Introduction 1

Applications 2

Configuration 2

Configuration Files................................................................................................... 2

Button Caps............................................................................................................ 3

Operation 4

Basic Control .......................................................................................................... 4

Advanced Control ................................................................................................... 5

Supplemental Guide – DOC. 7100C BPC(I)-8: onCue Basic Presentation Controller •1

BPC(I)-8: onCue®Basic Presentation

Controller

Introduction

The BPC-8 and the BPCI-8: onCue®Basic Presentation Controllers are compact, wall-

mount keypad controllers with eight assignable buttons for controlling a single projector, a

flat screen display, or a source device. The BPC-8 and the BPCI-8 can also be configured

to control a complete room presentation system equipped with a display device, a

motorized screen or lift, and a controllable source such as a DVD player.

The BPC-8 and BPCI-8 are functionally similar. For simplicity within this guide, the term

“BPC-8” is used except where noted.

For more information on the BPC-8, refer to the BPC(I)-8 DO Guide (Doc. 7194) at

www.crestron.com/manuals.

2•BPC(I)-8: onCue Basic Presentation Controller Supplemental Guide – DOC. 7100C

Applications

The following diagram shows the BPC-8 in a typical application:

Typical Application

Configuration

Configuration Files

These software configuration files are developed on a PC running the onCue BPC-8

software configuration tool. More information on the onCue product and instructions for

downloading the onCue BPC-8 Tool can be found at the onCue software website

(www.crestron.com/onCue).

The files are first uploaded to the handheld IR Learner & Programmer BPC-HPLIR (sold

separately). The BPC-HPLIR is then used to upload the files to the BPC-8 via the supplied

optical cable (refer to the following diagrams). Using this method, the user can add control

for any device that uses an IR remote, including projectors, displays, and DVD players. The

onCue BPC-8 Tool also allows for control of projectors via an RS-232 connection.

Supplemental Guide – DOC. 7100C BPC(I)-8: onCue Basic Presentation Controller •3

Develop Configuration Files

Upload Configuration Files

For more information, refer to the latest version of the BPC-HPLIR Supplemental Guide

(Doc. 7109) at www.crestron.com/manuals.

Button Caps

Configuration files developed for the BPC-8 typically require the button caps to be changed

or rearranged on the unit. The following figures illustrate the preinstalled button caps, the

five additional button caps supplied with the BPC-8, and the twelve button caps in the

Accessory Kit (sold separately).

Installed Button Caps

(Plus three blanks)

Supplied Button Caps

Accessory Kit (sold separately)

4•BPC(I)-8: onCue Basic Presentation Controller Supplemental Guide – DOC. 7100C

Operation

Basic Control

The BPC-8 is shipped with buttons preconfigured to control power, volume, mute, and

source select functions for a variety of display devices. Programs for these devices are

already stored in the BPC-8 memory.

NOTE: If a display device is not stored in the BPC-8, use the BPC-HPLIR IR Learner &

Programmer (sold separately) to develop a program for the device. For more information,

refer to the latest version of the BPC-HPLIR Supplemental Guide (Doc. 7109) at

www.crestron.com/manuals.

To select a display device, place the BPC-8 in Installer mode, and then enter the designated

code for the device. To enter codes, use the BPC-8 buttons that correspond to the

numbering arrangement shown below.

With the BPC-8 connected to the BPC-8-IMC and power applied, verify that the green

LEDs are on and then complete the following steps:

1. Press the top left and the bottom right buttons (buttons 1 and 8) at exactly the

same time and hold for 10 seconds. The back light LEDs (green) will blink twice to

confirm entry into Installer mode.

Entering Installer Mode

NOTE: If the buttons do not blink, the buttons were not pressed at exactly the

same time.

2. Enter the code for the chosen device. The backlight LEDs blink three times to

confirm the device’s program has been entered. The unit then exits Installer mode.

3. Press the BPC-8 power button (button 1) to verify operation. Verify that the

display’s power state changes. If the power state does not change, return to

Installer mode (step one), enter the next available code for the device (if any), and

repeat step two.

The BPC-8 exitsInstaller mode in the following instances:

•If the top-left and bottom-right buttons are simultaneously held down for 2 seconds

(the backlight will blink twice to confirm exit)

•After a 5-minute timeout (the backlight will blink twice to confirm exit)

•After a valid configuration is entered (the backlight will blink three times to confirm

exit)

Supplemental Guide – DOC. 7100C BPC(I)-8: onCue Basic Presentation Controller •5

Advanced Control

The BPC-8 is also capable of accepting custom configuration files that provide flexibility for

more complex installations. To create these files, complete the following procedure:

1. Use the Crestron Toolbox™ software onCue BPC-8 Tool to create a custom

configuration.

2. Upload the configuration to the BPC-HPLIR.

3. Connect the BPC-HPLIR fiber cable to the port on the bottom right of the BPC-8.

4. Press TRANSFER on the BPC-HPLIR.

This method allows the user to add control for any device that uses an IR remote, including

projectors, displays, and DVD players. The onCue Tool also allows for control of projectors

via an RS-232 connection (requires 4-Conductor Link Cable, CBL-SERIAL-DB9F-6 or

equivalent, sold separately).

For more information on creating custom configuration files, refer to the latest version of the

BPC-HPLIR Supplemental Guide (Doc. 7109) at www.crestron.com/manuals.

Crestron Electronics, Inc. Supplemental Guide – DOC. 7100C

15 Volvo Drive Rockleigh, NJ 07647 (2029035)

Tel: 888.CRESTRON 09.16

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Andere Handbücher für onCue BPC-8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Controller Handbücher

Crestron

Crestron infiNET EX CLC-FANDELVEX-W Bedienungsanleitung

Crestron

Crestron CLC-1LEDPWM-RGBW-EX Bedienungsanleitung

Crestron

Crestron MPC-M10 Maßzeichnung

Crestron

Crestron 302 Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-RMC-100-1 Anleitung zur Verwendung

Crestron

Crestron DGE-100 Betriebsanleitung

Crestron

Crestron TSW-1050-FMKT Bedienungsanleitung

Crestron

Crestron CGDMX-512BI Anleitung zur Verwendung

Crestron

Crestron C3COM-3 Bedienungsanleitung

Crestron

Crestron ST-VC Bedienungsanleitung

Crestron

Crestron CN-TVAV Bedienungsanleitung

Crestron

Crestron MPC-M5 Maßzeichnung

Crestron

Crestron MC2E Handbuch

Crestron

Crestron onCue BPC-8 Bedienungsanleitung

Crestron

Crestron C2N-SSC-2 Anleitung zur Verwendung

Crestron

Crestron PC-200 Betriebsanleitung

Crestron

Crestron CNXFZ Bedienungsanleitung

Crestron

Crestron CH-HREL8-D6 Bedienungsanleitung

Crestron

Crestron Zum ZUMMESH-CCO Bedienungsanleitung

Crestron

Crestron 4K DigitalMedia 3-Series Bedienungsanleitung

Crestron

Crestron 4K DigitalMedia 3-Series Maßzeichnung

Crestron

Crestron QM-RMC Bedienungsanleitung

Crestron

Crestron MPC-M10 Montage- und Bedienungsanleitung

Crestron

Crestron ZUMMESH-JBOX Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

Crestron onCue BPC-8 Betriebsanleitung

Beliebte Controller Handbücher anderer Marken