Crestron SP-RY Bedienungsanleitung
CRESTRON
Operations Guide - DOC. 5737 Relay Controller: SP-RY •• i
Contents
Relay Controller: SP-RY 1
Description 1
Functional Description 1
Physical Description 1
Specifications 2
Setup 3
SP-RY with SmartPresenter™3
SP-RY with SmarTouch™ST-CP 4
SP-RY with CNMSX 5
Programming 6
SmartPresenter™SP-1 6
SmarTouch™ST-CP 6
CNMSX 6
Problem Solving 7
Troubleshooting 7
Further Inquiries 7
Return and Warranty Policies 8
Merchandise Returns / Repair Service 8
CRESTRON Limited Warranty 8
CRESTRON
Operations Guide - DOC. 5737 Relay Controller: SP-RY •• 1
Relay Controller: SP-RY
Description
Functional Description
The SP-RY is a relay controller that allows easy control of devices needing low
voltage contact closures. The relays can be programmed using momentary, latching,
toggle and more through the Crestron software. The controller can be used with the
SmartPresenter, SmarTouch ST-CP, and CNMSX systems.
NOTE: The SP-RY provides four relays. Each set of two shares a common ground.
Physical Description
The SP-RY is a small unit with a permanently attached 3 ft. (91 cm) device cable.
The device cable consists of six wires, with stripped and soldered ends. A 3ft. (91
cm) Serial Data Cable is supplied for connection to the SmartPresenter or the
SmarTouch ST-CP systems.
SP-RY: Top View
CRESTRON
2•• Relay Controller: SP-RY Operations Guide - DOC. 5737
Specifications
Dimensions: Length 4.850" (123.19 mm)
Width 1.324" (33.63 mm)
Height 1.052" (26.72 mm)
Weight: 6.2 oz. (176 g)
Device Cable: Length 3' (91 cm)
Conductors (6) 22AWG
Serial Data Cable¹: Connector Type 3.5 mm, Straight, Stereo
Length 3' (91.44 cm)
Serial Data Cable²: Crestron p/n CNSP-112
12v DC Power Supply*: Crestron p/n PW-1205
(USA and Canada) Input 120V 60Hz 18W
Output 12vDC 0.5A
Crestron p/n PWI-1210
(International) Input 230V 50Hz 110mA
Output 12V---1.0A 12VA
Relay Ratings: 1A 30vDC
0.5A 30vAC
Software: SIMPL™ Windows®Version 1.20.04 or later
VisionTools Pro™ Version 1.1.3 or later
Crestron Database Version 11.7.207 or later
¹
For SmartPresenter and SmarTouch ST-CP (supplied)
² Required for use with CNMSX (Sold separately)
*
Required for use with SmarTouch ST-CP and CNMSX (sold separately)
1.052"
(26.72 mm)
1.324"
(33.63 mm)
4.850"
(123.19 mm)
Cable Length=3'
(91cm)
CRESTRON
Operations Guide - DOC. 5737 Relay Controller: SP-RY •• 3
Setup
SP-RY with SmartPresenter™
Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-RY.
Connect the other end of the cable to one of the outputs on the SP-1. The device
cable should be connected to the appropriate devices.
To locate the Q-Code for the Relay Controller, refer to the latest revision of the
SmartPresenter – Quick Guide (DOC. 5742).
NOTE: An external power supply is not necessary when using the SP-RY with the
SmartPresenter system.
Connect SP-RY to SP-1 and Devices.
To Devices
Serial Data Cable
Serial Data Cable
CRESTRON
4•• Relay Controller: SP-RY Operations Guide - DOC. 5737
SP-RY with SmarTouch™ST-CP
Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-RY.
Connect the other end of the cable to one of the outputs on the ST-CP. The cable
should be connected to the appropriate control device.
To program the ST-CP for the Relay Controller, refer to the SmarTouch STS Wizard
included with VisionTools Pro™or the latest revision of Crestron's SIMPL™
Windows®programming software (v 1.20.04 or later) and the latest version of the
Crestron Database (v 11.7.207).
NOTE: An external power supply must be used when using the SP-RY with the
SmarTouch ST-CP system.
Connect SP-RY to ST-CP
To Devices
Serial Data CableSerial Data Cable
Serial Data Cable
CRESTRON
Operations Guide - DOC. 5737 Relay Controller: SP-RY •• 5
SP-RY with CNMSX
The SP-RY can be used with a variety of Crestron systems, including the CNMSX.
When used with a CNMSX there are additional hardware requirements.
•A specially designed Serial Data Cable is required (p/n CNSP-112).
•An external power supply is required. Refer to "Specifications" on page 2
for part number and input/output voltage specifications.
Connect the stereo plug of the CNSP-112 into the input port of the SP-RY. Connect
the Phoenix type connector to of the CNSP-112 to one of the IR output ports on the
CNMSX.
To program the CNMSX for the Relay Controller, refer to the latest revision of
Crestron's SIMPL™Windows®programming software (v 1.20.04 or later) and the
latest version of the Crestron Database (v 11.7.207).
NOTE: An external power supply must be used when using the SP-RY with the
CNMSX system. A CNSP-112 Serial Data Cable is also required.
Connect to CNMSX
To Devices
Serial Data Cable
CNSP-112
G
S
External
Power Supply
Serial Data Cable
CNSP-112
CRESTRON
6•• Relay Controller: SP-RY Operations Guide - DOC. 5737
Programming
SmartPresenter™SP-1
The SmartPresenter is field programmable and does not require a PC. Refer to the
latest revision of the SmartPresenter – Quick Guide (DOC. 5742). SmartPresenter
software is available, however, it is only necessary for changing drivers, cloning
SP-1 machines, and updating firmware.
SmarTouch™ST-CP
The SmarTouch systems are easily programmed using the SmarTouch STS Wizard.
In several easy steps a SmarTouch system can be programmed and up-loaded. The
STS Wizard is available in VisionTools Pro™software.
SmarTouch systems may also be custom programmed using Crestron's easy-to-use
SIMPL™Windows®and VisionTools Pro™software.
CNMSX
The CNMSX is programmed using Crestron's easy-to-use SIMPL™Windows®
software.
Example Program shown as Block Diagram
This example allows a touchpanel to control a lift via the IR-Device (SP-RY).
Feedback is provided to alert the touchpanel user that a button is, in fact, being
pressed. The IR Device represents the driver for the SP-RY. This SP-RY driver can
be located in the Crestron Database (version 11.7.207 or later).
Inhaltsverzeichnis
Andere Crestron Controller Handbücher
Crestron
Crestron onCue BPC-8 Maßzeichnung
Crestron
Crestron ZUMMESH-JBOX Series Bedienungsanleitung
Crestron
Crestron CP4-R Bedienungsanleitung
Crestron
Crestron 4 Series Bedienungsanleitung
Crestron
Crestron QM-RMC Bedienungsanleitung
Crestron
Crestron DigitalMedia DM-RMC-100-1 Anleitung zur Verwendung
Crestron
Crestron CP3-R Bedienungsanleitung
Crestron
Crestron infiNET HTT-B10X Bedienungsanleitung
Crestron
Crestron ST-VC Bedienungsanleitung
Crestron
Crestron CEN-TVAV Bedienungsanleitung
Crestron
Crestron C3COM-3 Bedienungsanleitung
Crestron
Crestron C2N-SSC-2 Anleitung zur Verwendung
Crestron
Crestron MC2W Bedienungsanleitung
Crestron
Crestron C2N-SDC-DC Anleitung zur Verwendung
Crestron
Crestron CLS-EXP-DIMFLV Bedienungsanleitung
Crestron
Crestron PC-350V-12 Bedienungsanleitung
Crestron
Crestron 4 Series Bedienungsanleitung
Crestron
Crestron DigitalMedia 8G+ DM-RMC-200-C Maßzeichnung
Crestron
Crestron PC-350V Series Bedienungsanleitung
Crestron
Crestron 4K DigitalMedia 3-Series Bedienungsanleitung
