Crosley CB19G6W Bedienungsanleitung

Bottom Freezer

Warranty & Service ....... 23

Guide d'utilisation et

d'entretien ............ 24

Guia de Uso y Cuidado .... 48

Form No. A/or/e6 Part No. 12828162 Litho U,S.A.

ImportnntSnfetvInstructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground} prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

ImportnntSnfetvInstructions

SAVE THESE INSTRUCTIONS

Installation

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Leveling

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow '/2"space at top and Y2"space behind the

machine compartment cover (located in the rear) for

proper air circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

IMPORTANT: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging the

refrigerator in immediately may cause damage to

internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening

restraints may dent or damage outside finish.

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

• Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed

•%"hex head driver

•Carpenter's level

1. Remove toe grille.

• Grasp firmly and pull outward

to unclip.

2. Remove bottom bracket cover(s).

• Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

• Use slight pressure to pry the

cover loose.

• Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

Installation

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

C C

4. Using the carpenter's level, make sure front of

refrigerator is '/4" (6 ram) or '/2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. Turn stabilizing legs (C) clockwise until firmly

against floor.

6. Replace bracket cover(s).

• Position cover into the outer edge of the hinge.

• Swing the cover toward the cabinet and snap it

into place.

7. Replace the toe grille.

Note

• For proper reinstallation, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

1. Unplug power cord from power source.

2. Remove toe grille and bottom bracket

cover(s) (see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew _,6"hex head screws from

top hinge to remove hinge and retain ,_

all screws for later use.

5. Lift refrigerator door from center

hinge pin.

6. For swing freezer door models

only: Hold freezer door while

removing hinge pin with a Y,6"hex

head driver. Remove door from

bottom hinge and retain hinge pin

for later use.

For pullout freezer drawer models

only: Remove plastic sleeve, if t

Remove center hinge pin with a _,_" hex"

head driver. Retain hinge pin and

plastic sleeve for later use.

Remove Phillips screws to remove

center hinge and retain all screws for

later use.

Remove bottom hinge or stabilizing

bracket with _" hex head driver and

retain screws for later use. Lift out

bottom hinge pin (on freezer door

models).

If your model has a pullout freezer drawer, see

page 5 for drawer removal instructions.

Installation

Pullout Freezer Drawer

(select models)

To Install:

1. Pull both rails out to full

extension.

2. While supporting door front,

hook supports into tabs

located on inside of rail.

3. bwer door front into

final position.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

Lift lower basket straight up and out to remove.

On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

5. Remove Phillips screw

from each side of rail

system (select models).

6. Lift top of drawer front

to unhook supports

from rail system. Lift

door front out to

remove.

Replace and tighten Phillips screws that were

removed from each side of rail system (select

models).

Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

With rails pulled out to full extension, set the

basket straight down into the basket cradles.

Basket cradle

snap attachments

7Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Installation

Reinstallation of the Doors

1. Install hinge assemblies:

•Install top hinge loosely with 5/,6"hex head

screws.

• Install center hinge with Phillips screws.

• Freezer door models: Install bottom hinge with

3/8"hex head screws.

2. Freezer door models: Insert bottom

hinge pin.

• Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

3. Freezer door models: Place hinge

side of freezer door on bottom hinge

pin and hold freezer door upright

while installing center hinge pin with

5/,8"hex head driver.

• Replace plastic sleeve.

• Replace any applicable door shims.

• Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator

door on center hinge pin.

5. While holding refrigerator door

upright, tighten down top hinge

with 5/,8"hex head driver and

replace hinge cover.

Door Reversal

In some installations, reversing the door swing allows

for more convenient access to stored items. Both

doors can be reversed on freezer door models and the

fresh food door is reversible on freezer drawer models.

1. Remove door(s) (see page 4).

2. Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

• Remove cabinet plugs with flat

blade of screwdriver tip wrapped

in masking tape.

• Remove center mullion screws

with 5/,8"hex head screwdriver.

•Freezer door models: Remove

bottom mullion screws with 8/8"hex head driver.

3. Transfer door stops from bottom edge of fresh food

door and freezer door, if applicable, to opposite

side of door edge.

• Use a Phillips screwdriver

for removal and installation.

4. Install handles (see pages 6,

7 or 8).

5. Reinstall the door(s).

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Fresh Food Handles (select models)

Standard Front Mount Handle

Materials Needed

• Phillips screwdriver

• 6/,8"hex head driver

To Install:

1. Remove '/4"hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

• If reversing door, remove door

plugs from opposite side of door

and insert in screw holes.

2. Align handle holes with screw holes on

door face and secure with two door face

screws from step 1.

Installation

3. Locate handle trim in literature pack and

install over top and bottom of handle, as

illustrated.

• Secure top handle trim with remaining

screw removed in step 1.

• Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top

handle screw.

• Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

• Retain trim for later replacement.

3. Remove two hex head screws.

• Retain screws for later replacement.

Side Mount Handle (select models)

Materials Needed

• Phillips screwdriver

To Install:

1. Remove screws from the side of the

door.

2. Align the side mount handle with the

predrilled holes in the door panel.

3. Insert the screws in the sequence as

shown.

Upper

Handle

ii!iiiiiiiiiiiiiiiiiii_

40==

Lowe r

Handle

4. Ensure the door handle is snug to the

door panel.

To Remove:

Reverse installation procedure.

¸¸ !

Freezer Handles

Partial-Width Handle (select models)

Materials Needed

• Phillips screwdriver

To Install:

1. Install handle by fastening with

screws removed from edge of door.

• If reversing freezer door, remove

door plugs from top edge of door

and insert into screw holes.

To Remove:

1. Remove handle screws with Phillips

screwdriver and retain screws for

later use.

Front Mount Freezer Handle (select models)

Materials Needed

• Gloves to protect hands.

• Phillips screwdriver.

• Plastic handle removal card [or '/32"thick plastic

card). Retain the card.

Notes

• There is a slight curve to

this style of freezer

handle.

• For proper installation, be

sure handle is oriented as

shown.

To Install:

1. Align door handle clips slightly to the left of the

tabs attached to the freezer door.

2. Rotate the handle so the left base is flat against

the door.

Handle Door

Installation

3. Push the left handle

base against the left

door tab and slightly

to the right, just

enough to allow it to

hang unsupported.

4. While firmly supporting the left handle base against

the door, align the right base of the handle with the

right tabs that are attached to the door.

5. Now, while firmly holding the handle at the left and

right bases, gently slide the handle towards the

right until the right base settles in. The handle

should now be flat against the face of the freezer

door at both the left and right bases.

6. With hands still firmly keeping the handle flat

against the freezer door, you may have to reverse

directions momentarily to assure clip/tab

engagement. Then firmly slide the handle to the

right until it clicks. The audible "click" indicates

that the fastening clips are securely interlocked.

To Remove:

At the right end, flex the handle base away from

the surface of the freezer drawer. Simultaneously

slide the door handle removal card that came with

your refrigerator under the right side base of the

handle. Slide the card to the line indication or until

it stops, which will be approximately 1'/2".

With both hands, firmly grasp the handle towards

the right base.

Slide towards the left, lift and remove from the

surface.

TemperatureControls

Dial Temperature Controls

The controls are located at the top front of the

refrigerator and freezer compartments.

Note

•The freezer control turns the cooling system on.

Neither section will cool if freezer control is set to

OFE

Adjusting the Controls

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 13

for instructions on checking compartment

tern peratu re.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

Refrigerator Control • Allow 24 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Freezer Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• To adjust the controls, turn the control knob to the

left or right as desired.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Set the freezer control on 4.

• Set the refrigerator control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Temperature Control Guide

Refrigerator too warm Turn the refrigerator control

to next higher number.

Refrigerator too cold Turn the refrigerator control

to next lower number.

Freezer too warm Turn the freezer control to

next higher number.

Freezer too cold Turn the freezer control to

next lower number.

Turn refrigerator OFF Turn the freezer control to

OFE

Note

• Turning freezer control to OFF stops cooling in

both compartments. It does not shut off power to

the refrigerator.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Crosley Kühlschrank Handbücher

Crosley

Crosley 2314388 Bedienungsanleitung

Crosley

Crosley CT18GMXRQ01 Bedienungsanleitung

Crosley

Crosley CRH12RW Montageanleitung

Crosley

Crosley CRSE230KW0 Bedienungsanleitung

Crosley

Crosley XSS23G Betriebsanleitung

Crosley

Crosley CRSH268MB Bedienungsanleitung

Crosley

Crosley ZFDM2185RS Bedienungsanleitung

Crosley

Crosley CRD2121NW Bedienungsanleitung

Crosley

Crosley SIDE BY SIDE REFRIGERATOR Bedienungsanleitung

Crosley

Crosley CT16SKXSQ00 Bedienungsanleitung

Crosley

Crosley CRSN185UD Montageanleitung

Crosley

Crosley CFDMH 1834 AW Bedienungsanleitung

Crosley

Crosley CRSH268MS3 Bedienungsanleitung

Crosley

Crosley 241824400 Bedienungsanleitung

Crosley

Crosley CT14NKXHN00 Bedienungsanleitung

Crosley

Crosley CFDN2216AS Montageanleitung

Crosley

Crosley CBMH1873AW Bedienungsanleitung

Crosley

Crosley CRTEH182TW0 Betriebsanleitung

Crosley

Crosley Conservator American Tribute ARX443UW Bedienungsanleitung

Crosley

Crosley CT16SKXRQ00 Bedienungsanleitung

Crosley

Crosley Refrigerator Bedienungsanleitung

Crosley

Crosley CRSS262QB Bedienungsanleitung

Crosley

Crosley CRT181LWA Bedienungsanleitung

Crosley

Crosley XRS Betriebsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung