Cross Technologies 2083-2215 Bedienungsanleitung

Instruction Manual

Model 2083-2215

Dual Translator

September 2009 Rev B

MODEL 2083

TRANSLATOR

CROSS TECHNOLOGIES INC.

ALARMPOWER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2083-2215 Frequency Translator

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

1.3 Environmental Use Information 5

2.0 Installation 6

2.1 Mechanical 6

2.2 Rear I/O’s 7

2.3 Front Panel Controls, Indicators 7

2.4 Operation 8

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2083-2215 Manual- Rev B Page 2 9/08/09

2083-2215 Dual Translator

1.0 General

1.1 Equipment Description

2083-2215 Dual Translator - Consists of two converters (inverted spectrums) each of which convert a 1.725 -

2.175 GHz signal to a 0.95-1.4 GHz (LO =3.125 GHz). The two 1.725 - 2.175 GHz inputs are bandpass filtered

and then mixed with a 3.125 GHz synthesized local oscillator (LO) signal to 0.95-1.4 GHz. The mixer output

is applied to the output filters and amplifier. The converters have a nominal gain of 0 dB. All connectors are 75

ohm BNC female. Front panel LEDs light when DC power is applied (green) and when a PLL alarm occurs

(red). The 2083-2215 is powered by a 100-240 ± 10% VAC power supply and housed in a 1.75” X 19“ X 16”

1RU chassis.

MODEL 2083

TRANSLATOR

CROSS TECHNOLOGIES INC.

ALARMPOWER

FRONT PANEL

AC CHANNEL 2

OUTPUT

GND

CHANNEL 1

J4 J5J2

INPUT

J1 J10

MONITOR

AND

CONTROL

15 234 6789

OUTPUT INPUT

REAR PANEL

FIGURE 1.1 Front and Rear Panels

CH A

CH B

1.725

2.175

GHz

1.4 GHz LP

CH A

OUT

0.95 GHz HP

1.725

2.175

GHz

3.125

GHz

2083-2215 Block Diagram

1.7-2-2

GHz BP

PLL

CHANNEL B - SAME AS ABOVE

ALARM

0.95

1.4

GHz

OUT

CH B

OUT

0.95

1.4

GHz

OUT

FIGURE 1.2 Block Diagram

2083-2215 Manual- Rev B Page 3 9/08/09

1.2 Technical Characteristics

TABLE 1.0 2083-2215 Dual Frequency Translator Specifications*

EQUIPMENT SPECIFICATIONS*

Input Characteristics

Input Impedance/RL 75 Ω/12 dB

Frequency, 1.725-2.175 GHz

Input Level -10 to -30 dBm

Input 1 dB compression 0 dBm

Output Characteristics

Impedance/RL 75 Ω/12 dB

Output 1 dB compression 0 dBm

Output Level, Range -10 to -30 dBm

Frequency 0.95-1.4 GHz

Channel Characteristics

Gain at band center 0 dB ±2 dB, fixed

Frequency Response ±1.5 dB, 0.95-1.4 GHz out; ± 0.7 dB, any 36 MHz increment

Frequency Sense Inverting (1.725 GHz Translates to 1.4 GHz, 2.175 GHz

Translates to 0.95 GHz)

Intermodulation <-50 dBC for two carriers each at -13 dBm out

Spurious Response <-40 dBC, for 1.725-2.175 GHz input to 0.95 to 1.4 GHz out

0.95-1.4 GHz Feedthru <-30 dBC, min, <-40 dBC, goal

1.725-2.2 GHz Feedthru <-10 dBC, min, <-20 dBC, goal

LO rejection <-40 dBm, LO at the output

Synthesizer Characteristics

LO Frequency 3.125 GHz

Frequency Accuracy ± 1.0 ppm max

-110-95-80-80-70

1MHz100kHz10kHz1kHz100 Hz

dBC/Hz

Phase Noise

Fre

Indicators

DC Power; PLL Alarm Green LED; Red LED

Other

Connectors RF in and RF Out, BNC, female, 75 ohm

Connector, Alarm DB9 - NO or NC contact closure on Alarm

Size 19 inch, 1RU standard chassis 1.75”H X 16.0”D

Power 100-240 ± 10% VAC, 47-63 Hz, 15 watts max

*+10˚C to +40˚C; Specifications subject to change without notice

2083-2215 Manual- Rev B Page 4 9/08/09

1.3 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2083-2215 Manual- Rev B Page 5 9/08/09

2.0 Installation

2.1 Mechanical

The 2083-2215 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis.

A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2083-2215 can be

secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2083-2215 is assembled.

POWER

SUPPLY

FIGURE 2.0 2083-2215 Mechanical Assembly

2083-2215 Manual- Rev B Page 6 9/08/09

2.2 Rear Panel Input/Output Signals

Figure 2.1 shows the input and output connectors on the rear panel.

AC CHANNEL 2

OUTPUT

GND

CHANNEL 1

J4 J5J1

INPUT

J2 J10

MONITOR

AND

CONTROL

234 6789

AC1 - POWER IN

AC input for switching

power supply.

100-240 ±10% VAC,

47-60 Hz.

J10 - MONITOR AND CONTROL

DB9 female connector. see Table 2.1.

J5 - OUTPUT

950-1400 MHz,

-10 to -30 dBm output

see Table 2.2.

J4 - INPUT

1725-2175 MHz,

-10 to -30 dBm input

see Table 2.2..

OUTPUT INPUT

J1 - OUTPUT

950-1400 MHz,

-10 to -30 dBm output

see Table 2.2.

J2 - INPUT

1725-2175 MHz,

-10 to -30 dBm input

see Table 2.2.

FIGURE 2.1 2083-2215 Rear Panel I/Oʼs

TABLE 2.1 JJ10

TABLE 2.1 J10 Pinouts*

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

TABLE 2.2

Input/Output

2.2 Input/Output Connectoor

Connector Options

Option Input Output

STD BNC, 75ΩBNC, 75Ω

D BNC, 50ΩBNC, 50Ω

F Type F, 75 ΩType F, 75 Ω

*Remote Serial Interface

Interface: DB-9 Male

Protocol: RS-232C (RS-232C/422/485,

option Q), 9600 baud rate, no parity, 8 data

bits, 1 start bit, 1 stop bit.

2.3 Front Panel Indicators

Figure 2.2 shows the front panel indicators.

POWER ALARM

PLL ALARM

RED LED indicates

DC POWER

Green LED indicates

FIGURE 2.2 2083-2215 Front Panel Indicators

2083-2215 Manual- Rev B Page 7 9/08/09

2.4 Installation / Operation

2.4.1 Installing and Operating the 2083-2215, Frequency Translator Section

1. Connect a -30 dBm to -10 dBm signal to IN, J4 (Figure 2.1)

2. Connect the OUT, J5, to the external equipment

3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC on the back panel.

4. Set the desired output frequency band (See Section 2.5 Menu Settings).

5. Set the composite input level (See Section 2.5 Menu Settings).

6. Set the gain for 0 to +20 dB. Make sure the output stays within -30 to -10 dBm with the gain selected

and the input level provided. The firmware will prevent setting gain and input level outside this range.

(See Section 2.5 Menu Settings).

7. Be sure DS6 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).

8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the

drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a fuse

continues to open, the power supply is most likely defective.

AC Fuse - 2 amp slow blow (Type T),

5 mm X 20 mm

FUSE DRAWER

SPARE FUSE

INPUT

100-240± 10%VA

47-63 Hz

2A MA

FUSE

TYPE T 2A GDC

250 VOLT

FOR 100 - 240 V~

FIGURE 2.3 Fuse Location and Spare Fuse

2083-2215 Manual- Rev B Page 8 9/08/09

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

Printed in USA

2083-2215 Manual- Rev B Page 9 9/08/09

Andere Cross Technologies Elektronisches Wörterbuch Handbücher

Cross Technologies

Cross Technologies 3116 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-21T23 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-0312-30036 Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-66T42 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-84T78 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-T21-310212 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-T300 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-914A Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-T71 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-714A Bedienungsanleitung

Cross Technologies

Cross Technologies 2083 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-1919-02 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-31T21 Bedienungsanleitung

Cross Technologies

Cross Technologies 2483-40311 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-0703 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-6T4 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-T24 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-21-1422 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-1721 Bedienungsanleitung

Cross Technologies

Cross Technologies 2083-218 Bedienungsanleitung

Beliebte Elektronisches Wörterbuch Handbücher anderer Marken

Ectaco

Ectaco SAT-1600 Bedienungsanleitung

Sharp

Sharp PW-E310 Bedienungsanleitung

Franklin

Franklin BookMan III HBD-1450 Bedienungsanleitung

Eaton

Eaton DNP MINT Kurzanleitung

Franklin

Franklin IC-142 Bedienungsanleitung

Franklin

Franklin SCD-1890 Bedienungsanleitung

Franklin

Franklin SpellingAce SA-98 Bedienungsanleitung

Ectaco

Ectaco Language Teacher ECz600T Bedienungsanleitung

Franklin

Franklin BOOKMAN DMQ-440 Bedienungsanleitung

Besta

Besta cd 739p Gebrauchsanweisung

LEGRAND

LEGRAND tynetec ZXT360 Bedienungsanleitung

HORITA

HORITA RLT-50 Bedienungsanleitung

Language Teacher

Language Teacher ES400T Bedienungsanleitung

Accent

Accent 800 Bedienungsanleitung

SUPREME

SUPREME BTLT200 Bedienungsanleitung

Franklin

Franklin SCD-1870 Bedienungsanleitung

KMC Controls

KMC Controls KMD-5551E Benutzerhandbuch

Ectaco

Ectaco SpeechGuard TL-4 Bedienungsanleitung