Crosswater US-BL1000EV Bedienungsanleitung

Installation Instructions

Tubing

cutter

Adjustable

wrench

Pipe wrench

Channel

locks Hexagonal

key Teon

tape

Cross head

screwdriver

Flat head

screwdriver

Plumbers’ putty

or caulking

15/8”

51/2”

Finished

wall

77/8”

95/8”

COLD

INLET

HOT

INLET

81/4”

61/2”

Belgravia Exposed Thermostatic Valve

US-BL1000EV

Introduction

Installation notes

This exposed valve is suitable for use with all water systems up to a

maximum operating pressure of 72 psi and static pressure of 144 psi,

beyond which pressure-reducing valves must be installed . The

minimum water pressure requirement is 14.5 psi.

The outlet is controlled by a ow control cartridge, commonly used for

a main shower head.

IMPORTANT:

Please read these instructions carefully before beginning and

retain for future reference.

Roughing-in dimensions

Tools required

The installation must comply with all plumbing codes including local

codes. This valve is a mixing device and therefore requires the water

supplies to be reasonably balanced, otherwise we recommend a

pressure-reducing valve to be installed.

The valve is fitted with integral single-check valve cartridges,

therefore the exposed valve is protected against cross-flow due to

unbalanced line pressures.

Installing shut-off valves on incoming supply lines is recommended

for ease of maintenance.

IMPORTANT: Turn off the main water supply before connecting

to any existing pipework.

WARNING! Please check for any hidden pipes and cables, electric

or otherwise,before drilling holes in a wall or floor.

77/8”COLD

INLET

HOT

INLET

13/16”

max

lMake sure that the hot and cold inlet pipes have been installed

correctly.

lThe inlet pipes should be perpendicular to the wall, have a

maximum length of 13/16”, are level and are 7-7/8” apart as

shown opposite.

lPosition the valve onto the wall and mark the position of the

fixing holes (x4).

lDrill the fixing holes.

lMount the exposed valve to the wall using suitable fixings for the

wall construction.

lConnect the hot and cold water supplies and main outlet.

lOnce valve is installed add the riser rail to the top outlet. If

applicable, to install the bottom spout remove the stop located at

the bottom of the valve and connect on/off lever then spout.

lTurn on the water supplies and test all connections for

water leaks.

1Installation

2Installation

1/2" copper

HANDLE

COVER CAPS

SCREW

THERMOSTATIC

CARTRIDGE

Replacement part

US-WLBGEXPVLVCAR

LOCKING

NUT

STOP

RING CERAMIC

RING

VALVE

COVER

HANDLE

COVER CAPS

SCREW

NOTE: To avoid damage, please remove all finished parts

before maintenance takes place.

Thermostatic cartridges

lThe concealed thermostatic valve should give trouble-free

service, however servicing is a straightforward process.

To remove the thermostatic cartridge

lGently unscrew the cover cap from the handle.

lUndo the long screw and disassemble the parts as shown.

lUndo the cartridge locking nut, (take note of the orientation of the

cartridge).

lPull the cartridge out of the mixer housing.

lWash the cartridge with clean running water and make sure that

any trapped debris has been removed.

lDry and lightly grease the seals, (only use silicone grease), and

replace the cartridge.

lRe-assemble all parts.

3Maintenance

THERMOSTATIC

CARTRIDGE

Replacement part

US-WLBGEXPVLVCAR

Flow rate (PSI)

Flow rate (GPM)

1.5

1.3

2.6

3.9

5.3

6.6

3 4.5 6 7.25 14.5 30 44

lIAPMO certied to meet or exceed the following;

ASME A112.18.1 / CSA B125.1

ASME A112.1016-2011 / CSA B125.16-11

Spare parts

Appliance standards/codesFlow rate

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London,393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: technical@crosswaterlondon.com

Issue date: 27052021

Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray. This will

maintain the finish and avoid water spotting.

To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.

Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions to

ensure optimum results.

Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants will

alter the surface finish and void the warranty.

Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to

remain on the surface. Prolonged contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners as many can cause damage to the finish.

Please see the website for care instructions for specific finishes. ollow instructions to ensure optimum results.

Inhaltsverzeichnis

Andere Crosswater Steuereinheit Handbücher

Crosswater

Crosswater US-WF1000EV Bedienungsanleitung

Crosswater

Crosswater EV1253EC Bedienungsanleitung

Crosswater

Crosswater TH2-RGH Bedienungsanleitung

Crosswater

Crosswater SE350DC Bedienungsanleitung

Crosswater

Crosswater PBS-RGH Bedienungsanleitung

Crosswater

Crosswater KL0007WC Bedienungsanleitung

Crosswater

Crosswater WLBP3001R Plus Bedienungsanleitung

Crosswater

Crosswater US-DL2001RC Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung