Crosswater SW928116 Bedienungsanleitung

Installation and User

Manual

Electric Dual Fuel Heang Element

Installaon and User Manual — Electric Dual Fuel Heang Element

Please read these instrucons

carefully before starng installa-

on and keep in a safe place for

future reference.

Check the contents of the pack carefully be-

fore installaon. Responsibility will not be

held for any de-t / re-t costs where faulty

product has been ed. If any fault is found

with materials or workmanship, it must be

reported immediately to the manufactur-

er. Remedial acon will be taken, based on

informaon received, on condion that:

1. Full details are supplied to the

manufacturer;

2. The product has not been modied or

tampered with;

3. The manufacturer is informed of any

damage/shortages prior to installaon.

4. The product has not been installed, or

aempts have been made to install.

We do not accept responsibility for any prob-

lems that may occur through incorrect in-

stallaon. ENSURE the room is well heated

and venlated.

Any modicaon to the supplied product

will negate all product guarantees. Before

drilling ensure there are no hidden cables or

pipes (water, gas or electrical) behind hang-

ing points. Always wear suitable eye protec-

on when drilling. Ensure the wall surface

is able to take the weight of the complete

product. Please use the supplied wall x-

ing bracket and follow the correct installa-

on method. If the instrucons are not fol-

lowed appropriately there is an increased

safety risk to the user. It is important to in-

stall light ngs in the correct bathroom

zone i.e. the zone referred to in the IP rat-

ing of the element. This is not an installa-

on guide and reference should be made to

the latest edion of the IET Wiring

Regulaons or a qualied electrician mem-

ber of NICEIC or IET.

All electrical bathroom products should only

be ed by a suitably qualied, Part P reg-

istered electrician in accordance with cur-

rent IEE regulaons. Failure to have elec-

trical products installed and cercated by

a qualied electrical engineer will invalidate

any product guarantee. For full details ref-

erence should be made to the latest copy

of the IET wiring regulaons and all appli-

cable Brish Standard and European norm

specicaons.

WARNING

THIS PRODUCT MUST ONLY BE INSTALLED

IN A BATHROOM VIA A 5 AMP FUSED SPUR.

3 - PIN PLUG/SOCKET CANNT BE USED.

ONLY USE THE ELECTRIC ELEMENT

INDEPENDANTLY OF HEATING THROUGH

THE CENTRAL HEATING SYSTEM. NEVER

USE BOTH TOGETHER.

User Manual

Our products have been designed and manufactured in such a way to ensure

that all quality, functionality and aesthetic requirements are met.

Electric radiator

Guide to safe installation anduse.

1. Do not install the heater under an electrical socket point.

2. The towel warmer should be lled with a carefully measured amount of

liquid. In the case of loss of heating medium, or in any other case which

demands its supplementation, contact your installer.

3. The device is not equipped with an external temperature controller.

4. Electric heater is not a toy. Children under the age of 3 should not be al-

lowed within close proximity of the device without the supervision of an

adult.

Installaon and User Manual — Electric Dual Fuel Heang Element

Children aged 3 to 8 should only be allowed to operate the heater when

it has been properly installed and connected. The child must be under

adult supervision or have been trained to safely operate the device while

understanding the risks. To ensure the safety of very small children, in-

stall the electric dryer so that the lowest tube is at least 600 mm above

the oor.

5. Note: Some parts of the radiator can be very hot and can cause burns. Pay

special attention to the presence of children or people with disabilities.

6. If the towel warmer is used as a clothes and towel dryer, ensure that the

fabrics drying on it have only been washed in water, fully rinsed of any

acidic or alkali chemicals.

7. To ensure the safety of very small children, install the electric dryer so

that the lowest tube is at least 600 mm above the oor.

8. The device should only be installed by a qualied installer in accordance

with the applicable regulations regarding safety and all other regulations.

9. Extension leads or electric plug adapters should not be used in order to

supply power to the heater.

10. While connecting the radiator to electric installation ensure that the

curcuit has a 30 mA residual-current circuit breaker and an appropriate

overcurrent circuit breaker. With the permanent installation (cable con-

nection without plug) it is also mandatory to provide an omnipolar cut-

o switch with a minimum contact opening of 3 mm for disconnecting

the device on all poles.

11. The device version labelled PB can be installed in bathrooms in zone 1,

as dened by applicable law, subject to any additional regulations con-

cerning electrical installations in wet areas. Other versions of the device

can be installed in Zone 2 or beyond.

12. The device is recommended for use solely as described in the manual.

13. Ensure that the heater has been installed on a wall in accordance with

its installation manual.

14. Please forward this instruction manual to the end user for future reference.

Installaon and User Manual — Electric Dual Fuel Heang Element

Zone 1

Zone 2

600 mm

Electric Heating Element

Safety requirements — installation

1. Fitting and connection of the heating element should only be perform-

er by a qualied installer.

2. Only connect the element to a suitably rated electrical mains supply (see

the ratings on the element).

3. Switching on the heating element in the open air to test the device is per-

mitted for a maximum of 3 seconds.

4. Never test a heating element that is already installed. Do not turn the

heating element on in an empty radiator!

5. Ensure that the electrical cord does not touch the hot parts of the heat-

ing element or radiator.

6. Before installing or removing the device, make sure it is disconnected-

from the mains electrical supply.

7. Do not open the device — any interference with internal components

will invalidate the warranty.

8. The heating element’s power output must not exceed the radiators pow-

er output for the parameters 75/65/20° C.

Installaon and User Manual — Electric Dual Fuel Heang Element

9. The pressure in the radiator should not exceed 10 atm. Ensure that an

air cushion is preserved in electric radiators. In central heating systems,

leave one valve open to prevent pressure build up due to the thermal

expansion of the liquid.

10. The device is intended for home use only.

11. Fitting and Installation of the device must be carried out in accordance

with all local regulations for electrical safety, including installation within

permissible locations only. Observe bathroom electrical zone regulations.

Safety requirements — use

1. The heating element must be fully submerged in the heating liquid dur-

ing its operation. A radiator connected to the central heating system and

equipped with an electric heating element must be airvented regularly.

2. Regularly check the device for damage to ensure it is safe to use.

3. If the power cord is damaged the device should not be used. Unplug the

device and contact the manufacturer or distributor.

4. Do not allow ooding into the heating element casing.

5. Do not use the heating element in heating systems where the water tem-

perature exceeds 82° C.

6. The heating element and radiator can heat up to high temperatures.

Please be cautious — avoid direct contact with the hot parts of the

equipment.

7. Do not open the heating element casing.

8. In the central heating system, always make sure that one valve of the ra-

diator remains open.

9. Ensure that minors aged 8 and above or those with a physical or men-

tal disability are supervised if operating the device.

10. The device is not a toy. Keep it out of the reach of children.

11. The device must be disconnected from the mains during cleaning and

maintenance.

12. Cleaning of the equipment by children under 8 years of age is only per-

mitted under appropriate supervision.

Installaon and User Manual — Electric Dual Fuel Heang Element

Intended use of device

The heang element is an electric device

intended solely for installaon in radiators

(standalone or connected to the central

heang system).

Heang element power output should be

matched with radiator output for parame-

ters of 75/65/20° C

Technical informaon

Model markings

(power cable type):

PB (Straight cable without plug) *

Power supply: 230 V / 50 Hz

Insulaon class: Class I

Towel rail connecon thread: G 1/2"

Casing protecon class [IP]: IPx5

Powers available

Length of heang element:

400 600

335 365

* Device intended to be connected permanently to the system

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crosswater Heizung Handbücher

Crosswater

Crosswater bauhaus Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung