Crosswater WF6060 Bedienungsanleitung

ILLUMINATED MIRRORS - LED

Please read these instructions carefully before starting installation and keep in a safe place for future reference.

Check the contents of the pack carefully before installation. Responsibilty will not be held for any de-fit / re-fit costs where faulty product has

been fitted. If any fault is found with materials or workmanship, it must be reported immediately to the manufacturer. Remedial action will be

taken, based on information received, on condition that: 1. Full details are supplied to the manufacturer; 2. The product has not been

modified or tampered with; 3. The manufacturer is informed of any damage/shortages prior to installation. 4. The product has not been

installed, or attempts have been made to install. We do not accept responsibility for any problems that may occur through

incorrect installation. ENSURE the room is well heated and ventilated.

Before drilling ensure there are no hidden cables or pipes(water, gas or electrical) behind hanging points. Always wear

suitable eye protection when drilling.Ensure the wall surface is able to take the weight of the complete product.

It is important to install light fittings in the correct bathroom zone i.e. the zone referred to in the IP rating of the element. This is not an

installation guide and reference should be made to the latest edition of the IET Wiring Regulations or a qualified electrician member of

NICEIC or IET.

ZONE 0 is inside the bath or shower tray itself. Any appliance used in this zone must be rated at least IP67 which is total immersion proof.

ZONE 1 is the area above the bath or shower tray to a height of 2.25m from the floor. In this zone a minimum rating of IPX4 Splash-proof

is required and elements must also be protected by a 30mA residual current device (RCD) to protect the circuit.

The electrical connection to the power supply for these appliances must be in Zones 2/3 of the bathroom in compliance with

BS 7671:2008(2011) - IET Wiring Regulations.

ZONE 2 is an area stretching 0.6m outside the perimeter of the bath and to a height of 2.25m from the floor. In this zone an IP rating of at

least IP44 is required. In addition it is good practice to consider the area around a washbasin, within a 60cm radius of any tap to be

considered as zone 2.

Appliance must also be protected by a 30mA residual current device (RCD) to protect the circuit.

Failure to have electrical products installed and certificated by a qualified electrical engineer will invalidate any product guarantee.

For full details reference should be made to the latest copy of the IET wiring regulations and all applicable British Standard and European

norm specifications.

WIRING DIAGRAM

IMPORTANT ADVICE & SAFETY - please read before installation

This product is Class I rated

and MUST be earthed.

Supply 240v/50hZ maximum

This product is IP44 rated and is suitable for installation within zone 2 above, and complies with the following safety standards:

BS EN 60598-1: 2008+A11: 2009, EN60598-2-1: 1989

LIVE

EARTH

NEUTRAL

Live supply-Red or brown

Earth supply-Green/yellow

Neutral supply-Black or blue

Live - brown

Earth -Green&yellow

Neutral - blue

INSTALLATION INSTRUCTIONS

Remove all outer packing and carefully

Please do not lift the product by the plastic diffusers as this may

cause damage to your product.

check the product is in perfect condition.

The mirror is supplied with a protective film

DO NOT remove this until installation is

complete.

IMPORTANT

The product must be installed with a minimum distance of 150mm

between the infrared sensor and an adjacent wall surface, countertop

or other object to ensure correct function of the sensor.

It is recommended that walls are fully tiled/finished before installation. This ensures that the product is installed flat to the wall face and

allows product to be easily removed if required in the future.

STEP 1

Offer the mirror up to the desired wall location considering the safety zone

requirements. Using spirit level ensure the mirror is level and upright and

mark top of mirror. Using a soft pencil mark carefully the 2 fixing points.

WF6060 X=200mm A=170mm

MEA6080 X=130mm A=410mm

MET6080 X=590mm A=35.5mm

STEP 2

Carefully drill the required holes and insert wall plugs. Prepare the power

supply. Note screws and plugs supplied are suitable for solid walls only.

ENSURE THAT THE MAINS VOLTAGE SUPPLY TO WHICH THE

MIRROR IS BEING CONNECTED IS ISOLATED

Carefully feed the mains supply cable through the rubber grommet in the

mirror frame. Hold the mirror frame in the correct position, insert screws

and screw into wall plugs, ensure they are secure and the electrical mains

supply cable free from obstruction.

2 persons

Ph2

Ø8 mm

WF6060 MET6080MEA6080

MIN

150mm

Sensor switch

Touch switch

Xmm

Waste Electrical & Electronic Equipment Regulations (WEEE) requires that any electrical products showing the mark

above must not be disposed of with other household or commercial waste. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly at your

local facilities. Check with your Local Authority, Recycling Center or retailer for recycling advice.

CARE & MAINTENANCE

Add sentence:

LED light strips last for thousands of hours under normal domestic use, in the unlikely event that the LED light strip shouldfail please

contact customer services for a replacement part.- write this in bold type face.

Do not strike/hit glass components with hard or pointed items. Do not place very hot or very cold items against or in close proximity to

glass surfaces unless a suitably thick insulation material is used.

The nominal thickness of the mirror glass used in this product is 5mm and is safety film backed in accordance to BS:EN6206 for your

safety. If the mirror glass becomes chipped or broken, replace immediately. For details on replacement mirror glass and other

components contact customer services.

Cleaning:

The mirror edges are treated with a specially formulated sealant designed to protect the mirror edges from contaminants and

discolouring. Failure to follow cleaning guide-lines can/will remove the benefits of the sealant.

NEVER use products containing bleach, cleaners of a gritty or abrasive nature or so called “glass and mirror” cleaning products, that

can be detrimental to the long lasting finish of the mirror.

ONLY use a clean micro fibre cloth to clean the mirror and mirror frame.

Colour Coding:

L - Live = Brown

N - Neutral = Blue

Earth = Green & Yellow

THIS PRODUCT IS MANUFACTURED TO CLASS I

CATEGORY AND MUST HAVE AN EARTH CONNECTION

Hang the mirror onto brackets.

Apply a bead of clear silicone sealant on all sides between the mirror

frame and wall surface. Allow to dry for 24 hours.

Reconnect the electrical power supply.

OPERATING INSTRUCTIONS - SEE PAGE 4

To turn the mirror lights on or off, activate the switch by passing your hand over the sensor.

Remove protective film from the mirror face, and clean as directed

below.

STEP 3

STEP 4

Tube Type

Model Led Parameter Led Driver

WF6060

69X2 Leds / 0.06W / 6400K

117 Leds / 0.06W / 6400K

312 Leds / 0.06W / 6400K / 4000K

42 Leds / 0.2W / 6400K / 4000K

15W

MET6080

MEA6080

Remove the cover from the electrical connection box. Using a

suitable terminal screwdriver make secure connections as follows:

Live Terminal

Connecon

Earth Terminal

Connecon

Output Wires

Neutral Terminal Connecon

For any further information please contact call us on:

0345 873 8840

Or visit our web-site at:

www.bauhaus-bathrooms.co.uk

No part of this document may be reprinted or duplicated without

Crosswater Holding's consent. In the interests of continued

product development Crosswater Holdings reserves the right to

alter specification without prior notification. E & OE.

To turn illumination on touch the sensor once.

To change the colour temperature, touch and hold the

sensor until desired light temperature warm or cool is

obtained.

The colour temperature is then set until changed again.

To turn illumination on or off, wave your hand under

the sensor switch located at the bottom of the mirror.

The heated pad will operate when the light is illuminated;

The heat pad will work if the mirror lamp(s) expire.

Once turned on the heating pad will warm the mirror and

clear the surface of condensation.

LED

Mirror

This luminaire

contains built-in

LED light strips

The lamps cannot be changed

in the luminaire.

874/2012

Energy label

Dieses Handbuch passt für folgende Modelle

Andere Crosswater Körperpflegeprodukt Handbücher

Crosswater

Crosswater Waldorf US-WF6060 Bedienungsanleitung

Beliebte Körperpflegeprodukt Handbücher anderer Marken

Pretika

Pretika ST102 Bedienungsanleitung

Beurer

Beurer FC 76 Bedienungsanleitung

Pebble Grey

Pebble Grey 500.40.70-75 Bedienungsanleitung

PUSH

PUSH ortho Bedienungsanleitung

Dermlite

Dermlite DL3N Bedienungsanleitung

DERMAPEN

DERMAPEN SEMI Bedienungsanleitung

HiB

HiB Spectre 50 Bedienungsanleitung

Carex

Carex SunLite Bedienungsanleitung

Roper Rhodes

Roper Rhodes Intense Stücklistenhandbuch

Interacoustics

Interacoustics Titan IMP440 Bedienungs- und Sicherheitshinweise

ReTrak

ReTrak VS001 Bedienungsanleitung

LED Technologies

LED Technologies dpl PAIN RELIEF Joint Wrap Bedienungsanleitung

Casa Lusso

Casa Lusso MVL1000x450PR Bedienungsanleitung

Quoizel

Quoizel QR3326 Montageanleitung

BERTSCHAT

BERTSCHAT HEATED HOODIE PRO - DUAL HEATING Bedienungsanleitung

Beurer

Beurer EM 37 Bedienungsanleitung

ACP

ACP OMNISTAND Bedienungsanleitung

Scarlett

Scarlett VitaSpa SC-CA304PS11 Bedienungsanleitung