This clock is designed for operation from a 12 volt DC source only (10.6 to 16v)
Current dra hen connected to a 12v supply is approximately 50mA (.05 Amps)
Allo able ambient temperature range -20 to + 50° C
Backup Batteries are fitted for clock memory. Remove the plastic insulator on the battery compartment before use.
To replace the batteries, remove the single scre holding the small access plate on the rear and remove the plate by
lifting the end here the scre as. Place a small pointed object under a corner of the batteries and ‘flick’ them out.
Replace ith Lithium Cells LR44 or equivalent. Observe Polarity when fitting: + side must be up
When the batteries are fitted, but the clock is not connected to a 12v source, only the Clock function ill operate
Power cable has a Cigar Lighter plug attached.
The cigar plug requires the vehicle socket to have Positive + at the tip connection.
All negative chassis vehicles are ired this ay, but a vessel may not be. If in doubt check ith a voltmeter first.
Warranty is void if incorrectly ired.
Where it is desired to permanently ire the clock into the 12v electrical system of a vehicle, vessel etc, rather than
using the cigar plug/socket combination, the cigar plug can be removed, ithout voiding the Warranty.
Observe the correct polarity if doing this: The wire with the WH TE STR PE is to Positive +
The plain BLACK wire goes to negative -
The ire is of light gauge. Ensure it is properly connected, ell supported and provided ith proper strain relief.
As usual best practise, please ensure all + iring is fused as near as possible to the voltage source and run in a
orkmanlike manner. All connections must be secure, lo resistance and protected. Use a fuse rating of 1/2 an Amp
Temperature lead/sensor can be placed or mounted in any convenient location, but it is not intended to be placed
here it ill get et. The back of the sensor has sticky tape attached. Remove the protective paper from it to use.
Mounting pedestal s ivels vertically, hilst the foot can rotate, or be removed. The foot has sticky tape already
attached, but for a more robust mounting it may be advantageous to drill 2 holes through the foot for scre fittings.
(PRE JUNE 2016) 7045V D G TAL CLOCK NSTALLAT ON NOTES
OPERAT ON
The Clock should be connected to the 12v source to carry out the setting procedures
When carrying out setting procedures the clock ill exit from the setting mode if no button is pressed for 60 seconds
SETT NG THE T ME FORMAT TO 12 OR 24 HOUR
From the normal time display, press and hold TIME. Press UP to toggle the display bet een 12hr or 24hr Format
Subsequent presses ill toggle the display 12 or 24 Hour alternately
REMEMBER: 24 hour mode ill sho as a different display only if the time is after 1pm (1300 hrs)
When in 12 Hour display mode AM or PM is sho n on the far left of the display.
SETT NG THE T ME AND CALENDER
From the TIME display, press and hold TIME until 12H or 24H is displayed. Press TIME again t ice.
The Hours display ill flash. Press UP or DOWN to adjust to the desired setting.
Press TIME once, the Minutes display ill flash. Press UP or DOWN to adjust to the desired setting.
Press TIME once, the calendar Year ill flash. Press UP or DOWN to adjust to the desired setting.
Press TIME once, the calendar Month ill flash. Press UP or DOWN to adjust to the desired setting.
Press TIME once, the calendar Day ill flash. Press UP or DOWN to adjust to the desired setting.
To set the clock accurately to radio time pips or similar:
Set the time as above, but set it to 1 minute ahead of actual time.
From the TIME display, press and hold TIME, until 12H or 24H is displayed. Press TIME once again.
The seconds display is no flashing
Pressing UP at the instant of the beginning of the last time pip ill reset the seconds display to zero
ALARM
To vie the current alarm time setting press ALM. To return to the normal time display press TIME
Setting the Alarm
From the normal Time display:
Press ALM once, the display ill read the current set alarm time
Press and hold ALM until the hours display flash
Press UP or DOWN to adjust to the desired Hour setting.
Press ALM once. The minutes display ill flash.
Press UP or DOWN to adjust to the desired setting.
Press ALM once. The Alarm time is no set, but the Alarm is still not turned on
Press UP once more to turn the alarm on. A small bell ill be sho n on the display.
