Crypto F200 Bedienungsanleitung

USER MANUAL

F200 ADSL USB MODEM

CONTENTS

1. Introduction 4

2. Specifications 4

2.1 ADSL Standards supported 4

2.2 Supported Protocols 4

2.3 Connections 5

3. Hardware Installation Procedures 5

3.1 Hardware Requirements 5

3.2 Preparing your network information 5

3.3 Configure the ISP parameters for your Windows XP 6

3.4 Driver Installation on Windows XP 7

3.5 Software Configuration 8

3.6 Connection to the Internet 11

4. Troubleshooting 13

1. Introduction

F200 ADSL USB modem is a high performance and high-speed device that

provides a full rate ADSL modem with the superb reliability and is a complete

solution for home and office. The F200 ADSL USB modem can have a maxi-

mum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps.

You can safely enjoy the new generation broadband Internet with the F200

ADSL USB modem. Included drivers for Win98/ ME/ 2000/ XP.

2. Specifications

2.1 ADSL Standards supported:

ñSupports ITU-T G.992.1(G.DMT) and ANSI T1.413 Issue 2

ñSupports G.992.2 (G.LITE)

ñAnnex A & B

2.2 Supported Protocols:

WAN

ñPPP over ATM (PPPoA) VC MUX

ñPPP over ATM (PPPoA) with LLC/SNAP

ñPPP over Ethernet (PPPoE) with LLC/SNAP

ñPPP over Ethernet (PPPoE) with VC MUX

LAN

ñBridged Ethernet (IP over ATM) with LLC/SNAP

ñBridged Ethernet (IP over ATM) with VC MUX

ñRouted IP over ATM with LLC/SNAP

ñClassical IP over ATM

This package includes:

ñF200 USB modem

ñ1 USB cable

ñ1 RJ11 telephone cable

ñ1 CD with drivers

ñ1 users manual

2.3 Connections

USB – Connects the USB cable from the USB port of the F200 modem to the

USB port of the computer.

LINE – Connects the RJ11 telephone cable from the telephone line port of

F200 modem to the telephone plug..

LED indications:

POWER: After successfully installing the modem, the POWER LED light turns

on. It will stay on every time you start your computer.

3. Hardware Installation Procedures

3.1 Hardware Requirements

The following hardware is necessary to configure and use the F200:

ñRJ-11 (ADSL Ready) telephone Line

ñUSB cable (Included in the package)

3.2 Preparing your network information

To configure your ADSL modem smoothly, it is required that you contact your

ISP (Internet Service Provider) and acquire the following information:

Type of Mode Encapsulation used:

a. PPPoE, PPPoA, IPoA, Bridged or Routed.

DSL connection parameters:

b. For PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by your

ISP). During the driver installation, select ‘WAN’.

c.For Bridged, Routed, or IPoA, refer to Table 4 and fill-in all values (provided by

your ISP). During the driver installation, select ‘LAN’.

Table 3 WAN (PPPoE/PPPoA parameters)

Information Value

PVC Settings VPI

VCI

Encapsulation (LLC ‹ VCMux)

Information Password

Line Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferred

ITU (G.dmt or G.lite)

G.dmt

G.lite

table 4 LAN (Bridged/Routed/IPoA parameters)

Information Value

PVC Settings VPI

VCI

Encapsulation (LLC or VC Mux)

IP Information IP Address

Subnet Mask

Gateway IP Address

Preferred DNS address

Alternate DNS address (If available)

Line Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferred

ITU (G.dmt or G.lite)

G.dmt

G.lite

3.3 Configure the ISP parameters for your Windows XP

F200 is initially set to function on Annex B protocol (ADSL over ISDN). To

install the F200 based on Annex A protocol ( ADSL over PSTN), follow the

procedure below.

NOTE: THE FOLLOWING PROCEDURES APPLY FOR PPPoA MODE..

Table 5

Annex A

Driver Setup ‰È·Ï¤ÁÔ˘ÌÂ WAN

Protocol PPPoA

Encapsulation VCMUX

Modulation Automatic ITU G.dmt or G.lite preferred

VPI 8

VCI 35

USERNAME test

PASSWORD test_passw 6

3.4 Driver Installation on Windows XP

Step 1:

Windows will detect the newly installed device

and the screen below will appear after the

F200 USB ADSL Modem is attached to the

systems USB port.

Select "Install from a specific Location",

and click "NEXT".

Step 2:

Select "Include this location in the search"

and type d:\driver\Wan

(where D:\ the CD-ROM)

Note: If the protocol being used is Bridged,

Routed or IpoA, then type d:\driver\Lan

Step 3:

Click Continue Anyway.

This window appears only on Windows XP.

Installation continues

Step 4:

Click "Finish"

Step 5:

Left click on 'My Computer' icon and

click on 'Properties_ > _Device Manager'

Double click on Network adapters and

check to see for:

'Crypto F200 USB ADSL WAN adapter'

3.5 Software Configuration

Continue the setup process of the F200.

Step 1:

Double click on

the ‘Access Runner’ icon

Step 2:

Initially there is no connection / synchronization

with the ADSL line ‘Attempting to Activate Line’.

Press ‘ALT – P’ on your keyboard

Step 3:

Here you can see that the connection has

not been established. ‘Attempting to Activate Line’.

Click the ‘Line Setup’ tab

Step 4:

Initially it is set to Annex B (ADSL over ISDN) as

shown on the bottom right.

Note: If the line was ISDN, then we do not change it.

Step 5:

Select Annex A (ADSL over POTS) (given that the line

was PSTN). Click Apply.

Note: Incase you take out the USB plug from your

computer and plug it back to the USB port of the

computer again (does not matter if its upon shut-down

or while the computer is on), then the Annex selection

will automatically be set to Annex B. To set it back

to Annex A, please follow this procedure again.

Select the Protocol Setup tab

Step 6:

In the Virtual Path Identifier (VPI) selection, and

under Virtual Circuit 0, the value is 0.

and

In the Virtual Circuit Identifier (VCI) selection, and

under Virtual Circuit 0, the value is 35.

Step 7:

For the example insert:

VPI = 8

VCI = 35

Click Apply.

Step 8:

For Encapsulation Mode select the connection

protocol:

PPP over ATM VCMUX (RFC2364)

Click Apply

Click on the General tab

Step 9:

Under Line Status, the indication ADSL Connection

Established, indicates that the connection /

synchronization with the ADSL line has been done

with success.

Note: 1 to 2 minutes are required after you make

the above configurations, in order for the F200 to

be synchronized with the ADSL line.

Step 10:

To see information regarding the connection,

click the Physical Layer Statistics tab,

and click OK.

Inhaltsverzeichnis

Andere Crypto Modem Handbücher

Crypto

Crypto ReDi PC 250 Gebrauchsanweisung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung