CTC Union EOC-10 Bedienungsanleitung

Ethernet Over Coaxical Cable

Quick Start Guide

8/2008

Ver. 1.0

Table of Contents

Installation Instructions

EOC-10 Non-Managed Stand-Alone

Ethernet Extender over Coaxial Cable

Introduction

Features

Speciﬁcations

Installation

Connections

Application Notes

CE Notice

------- 1

------- 2

------- 3

------- 5

------- 6

------- 7

Features

 High-Speed 160Mbps communications link over existing Coaxial Cable,

Symmetrical on EoCNA.

 160Mbps@ up to 800 meters (2,624feet), reach down to 4Mbps@ about

1.2Km (4,000feet).

 Operates transparently to higher layer protocols such as TCP/IP.

 Auto-MDIX and Auto-negotiation 10Base-T or 100Base-TX and Full or

Half-Duplex on the Ethernet port.

 Plug and Play design for simple installation, no conﬁguration or

switch setting.

 Status LEDs for simple monitoring of the device and connection status.

Introduction

The EOC-10 is point-to-point EoCNA (Ethernet over Coax Network)

solution that eﬃciently extends 10/100 Ethernet circuits to over 800

meters (2,624feet) at up to160Mbps using existing coaxial cable.

The EOC-10 will allow Ethernet connectivity in existing facilities

without pulling extra cable. This is perfect solution for home Ethernet

or anywhere coaxial cable already exists. Installation is easy, just

connect a coaxial cable between the “trunk” connections of two EOC-10.

The EOC-10 uses coaxial cable to extend Ethernet connectivity over

existing CCD/CATV cable.

---------1---------

TRUNK DC 5VCATV LAN

PWR Link/ActSyncMode

COAX

LAN

Link/Act

EOC-10

Front Panel of EOC-10

Rear Panel of EOC-10

LED Indicators

EoCNA

Connection CATV

Connection Fast Ethernet

Connection DC Jack

Speciﬁcations

 Network Standards

ITU G.9954，Ethernet Over Coaxial Network (EoCNA)

IEEE802.3 10BASE-T, 10Mbit/s

IEEE802.3u 100BASE-TX, 100Mbit/s, Auto-negotiation

IEEE802.3x Full Duplex and Flow Control

 Protocol:

Transparent to higher layer protocols

 Connectors

Fast Ethernet：One RJ45 Connector

Coax：Two F-Type Female Coax Connectors,

One for EoCNA, the other for TV

 Transmission Power and Spectrum

0 +/-0.5 dBm

12-28 MHZ

 Transmission Speed and Distance

Up to 160Mbps@800 meters

Up to 4000 Feet (-176dBm/Hz Noise Floor)

 Fast Ethernet Interface

10/100 Mbps

MDI/MDI-X Auto Crossover

Priority Base on IEEE802.1p and TCP/UDP port

---------3------------------2---------

Connection

The following example illustrates the connection scheme when connecting

a remote LAN to the central IP network via coaxial cable.

Installation

Connect the Ethernet cable to RJ-45 LAN port. Follow the connection

examples below. Install the EOC modem with the DC power adapter

provided (+5VDC) and connect the adapter to an AC outlet. The EOC-10

modem will sense whether to operate in Half Duplex mode and Link

status will be indicated on the LED.

Speciﬁcations (continued)

 Indicators

“Power” LED

EoCNA Link/Act, SyncMode LED

LAN Link/Act LED

 Environmental Conditions

Operating Temperature: 0oC ~ 55oC (32oF~ 131oF)

Storage Temperature: -10oC ~ 65oC (14oF~ 149oF)

Operating Humidity: 10% ~ 90% Non-condensing

 Power Requirement

External Power Supply: 5V DC

Power Consumption: < 3.25 Watts

 Physical Dimension

155mm(W) x 83mm(D) x 30mm(H)

Unit Weight: 300g

 Emissions Compliance

FCC part 15 Class B, CE EN55022/EN55024

CATV

10/100 Fast Ethernet Switch

DC Power DC Power

IP NetworkIP Network

LAN DC 5V

LAN DC 5VTrunk CATV Trunk CATV

Coax

---------5---------

---------4---------

Application Notes

 Extend LAN connectivity to a remote site or between buildings.

 Connect Ethernet in diﬀerent rooms over existing home coaxial

infrastructure.

 Connect new controller technology on the factory ﬂoor using existing

coaxial cable.

 Extend Ethernet connectivity from a backbone network to an isolated

location via coaxial cable.

 Transmit video and traﬃc controller information over existing coaxial

cable.

Local Side

LAN DC 5V

10/100 Fast Ethernet Switch

Remote Side

LAN DC 5V

10/100 Fast Ethernet Swtich

Remote Side

LAN DC 5V

Splitter

CATV

10/100 Fast Ethernet Switch

Trunk CATV

Figure: EOC-10 Application

CE NOTICE

Marking by the symbol CE indicates compliance of this equipment to the EMC directive of the

European Community.

Such marking is indicative that this equipment meets or exceeds the following technical standards:

EN 55022:1994/A1:1995/A2:1997 Class A and EN61000-3-2:1995, EN61000-3-3:1995 and EN50082-1:1997

---------7---------

---------6---------

Inhaltsverzeichnis

Andere CTC Union Extender Handbücher

CTC Union

CTC Union VDTU2-B110 Bedienungsanleitung

$CTC Union TEX-100 Bedienungsanleitung$

CTC Union

CTC Union TEX-100 Bedienungsanleitung

CTC Union

CTC Union IEXT224-4PH-L Bedienungsanleitung

CTC Union

CTC Union FRM220A-Eoe1 Bedienungsanleitung

CTC Union

CTC Union VDTU2A-304 Bedienungsanleitung

CTC Union

CTC Union SHDTU03b-ET100BS Bedienungsanleitung

CTC Union

CTC Union G.SHDSL.bis Bedienungsanleitung

CTC Union

CTC Union EOC-101L-P Bedienungsanleitung

CTC Union

CTC Union VDTU2A-301 Bedienungsanleitung

CTC Union

CTC Union VDTU2A?104L?4PH Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung