CTC Union EcoLogic S EcoAir Handbuch

Providing sustainable energy solutions worldwide

162 605 06-2 2021-03-26

Important!

• Read carefully before use, keep for future reference.

• Translation of the original instructions.

Installation and Maintenance Manual

CTCEcoLogic S

162 605 06-2 2021-03-26

Installation and Maintenance Manual

CTCEcoLogic S

4CTC EcoLogic S

Table of Contents

Important to remember! ______________________________________________ 6

Safety instructions _______________________________________________________ 7

1. Design ____________________________________________________________________ 8

1.1 Display unit________________________________________________________8

1.2 Technical data____________________________________________________8

1.3 Scope of delivery _______________________________________________9

2. EcoLogicS areas of use_____________________________________ 10

2.1 Heating systems with/without 3-way valve __________10

2.2 Heat pump for Property Control (BMS) _______________12

3. Detailed menu descriptions _______________________________ 13

3.1 Start menu ______________________________________________________13

Installer ___________________________________________________________________15

3.2 Display____________________________________________________________ 16

3.3 Settings __________________________________________________________18

3.4 Deﬁne _____________________________________________________________23

3.5 Service____________________________________________________________24

4. Parameter list ______________________________________________________ 27

5. Electrical installation___________________________________________ 28

5.1 Power supply __________________________________________________ 28

5.2 Communication between EcoLogic and EcoAir/

EcoPart___________________________________________________________ 28

5.3 Outdoor sensor B15 (EcoPart)___________________________ 28

5.4 Thermostat control K26 / control signal external

3-way valve _____________________________________________________28

5.5 Connecting to terminal block and circuit board A5__

5.6 Connecting a separate communication cable______ 29

5.7 Connecting control card EcoAir/EcoPart_____________ 30

6. Installation Communication _______________________________ 31

6.1 CTC Remote - Screen Mirroring_________________________ 32

6.2 MyUplink - App________________________________________________32

7. First start______________________________________________________________ 33

7.1 Before ﬁrst start _______________________________________________33

7.2 First start_________________________________________________________33

8. Operation and Maintenance ______________________________ 34

9. Troubleshooting/

Appropriate measures ________________________________________ 34

9.1 Information messages ______________________________________ 36

9.2 Alarm messages ______________________________________________36

10. Appendix______________________________________________________________ 39

10.1 Types of Operation with CTC EcoEl V2 _______________ 39

5CTC EcoLogic S

You have just purchased a CTC EcoLogic S. Save this

manual containing the installation and maintenance

instructions. You will be able to enjoy the beneﬁts of

your CTCEcoLogicS for many years, and this manual

provides all the information you will need.

CTC EcoLogicS has a control system that:

• allows supplementary heat pumps to be added to

existing systems.

• monitors and controls your heat pump.

• allows for individual settings.

• displays desired values, for instance, temperature

and operating status.

• allows settings to be made in a simple and

structured manner.

Congratulations on your new product!

Thanks to the ﬂexible set-up with clear and simple

options for settings, CTC EcoLogicS is the perfect

solution for adding heat pumps to existing systems.

CTCEcoLogicS is fully equipped for connection with

the CTC EcoAir outdoor air heat pump or CTC EcoPart

ground source heat pump.

6CTC EcoLogic S

Important to remember!

Check the following points in particular at the time of delivery and installation:

• Remove the packaging and check that the product (electrical

connection box and display) has not been damaged in transit. Report

any transport damage directly to the carrier.

• Check for missing parts.

• The product must not be installed where the ambient temperature is

higher than 60°C.

• CTC EcoAir/EcoPart must have software version HP control card

2020-11-01 or later. If the software version is older than this, contact

your installer for information on how to update the software.

• Register your product for warranty and insurance via the website

https://www.ctc-heating.com/customer-service#warranty-registration

No liability is accepted for any misprints. We reserve the right to make design changes.

For your own reference

Fill in the information below. It may come in useful if anything should happen.

Product: Serial number:

Installer: Name:

Date: Tel. no.:

Electrical installer: Name:

Date: Tel. no.:

If these instructions

are not followed

during the installation,

operation and

maintenance of the

system, Enertech’s

liability under the

applicable warranty

terms is not binding.

!Information in

this type of box

[!] is particularly

important for

correctly installing

and using the

product.

iInformation in this

type of box [i] is

intended to help

ensure that the

product functions

optimally.

7CTC EcoLogic S

Turn off the power with an omnipolar switch before doing any work on the product.

The product must be connected to protective earth.

The product is classified as IPX1. The product must not be rinsed with water.

When handling the product with a hoist ring or similar device, make sure that the

lifting equipment, eyebolts and other parts are not damaged. Never stand under the

hoisted product.

Never jeopardise safety by removing bolted covers, hoods or similar.

Any work on the product’s cooling system should be carried out by authorised

personnel only.

The product’s electrical systems should only be installed and serviced by a qualified

electrician.

-If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

Safety valve check:

-Safety valve for boiler/system to be checked regularly.

The product must not be started if it is not filled with water; instructions are in the

“Pipe installation” section.

WARNING: Do not switch on the product if there is a possibility that the water in the

heater is frozen.

This device can be used by children from the age of eight years and above and by

people with reduced physical, sensory or mental ability or lack of experience or

knowledge if they have been taught, either with supervision or with the instructions

provided, how to use the device safely and understand the risks involved. Children

should not play with the device. Cleaning and maintenance should not be carried

out by children without supervision.

If these instructions are not followed when installing, operating and maintaining the

system, Enertech’s commitment under the applicable warranty terms is not binding.

Safety instructions

DCB

8CTC EcoLogic S

1. Design

A USB port

B Power supply display unit/internal communication

C Network connection (Ethernet)

D BMS connection

E Display unit

CTC no. EcoLogic S (EcoAir / EcoPart) 6212576 / 6212593

Supply 24V DC

Outdoor sensor (CTC EcoPart) 2.2 kΩ

Display

Memory

Backup batteries

Clock

4.3 inch colour touchscreen

retains memory during power failure

not required

controlled in real-time

Weight (packaged weight) 0.8 (1) kg

Display dimensions (depth x width x height) 28 x 159 x 160 mm

Enclosure class (IP) IP X1

1.1 Display unit

1.2 Technical data

9CTC EcoLogic S

1.3 Scope of delivery

The ﬁgure below shows the main components in the EcoLogic delivery.

F Communication cable display unit – heat pump

G Outdoor sensor (applies to connection to heat pump, model CTC EcoPart)

H Installation and Maintenance Manual

I Display unit bracket

J Ferrite

G11

10 CTC EcoLogic S

2. EcoLogicS areas of use

2.1 Heating systems with/without 3-way valve

System description

Thanks to the settings options in EcoLogicS, operation of the heat pump can be adapted to

the existing boiler’s conditions and settings.

The control of the existing heating system manages the distribution of heat and hot water in the

same way as before.

Conditions

The installation must be adapted on a case-by-case basis depending on the conditions of the

existing heating system. It is important that installation is carried out in full accordance with the

respective product’s installation instructions. Refer to the relevant heat pump manual for details

about electrical installation, ﬂow requirements, volume requirements, temperature requirements

and more. In some cases, the existing boiler’s settings may need to be adapted to enable heat

pump installation.

The heat pump’s operating parameters must be adjusted in relation to the existing heating

system setting. The main principle is that EcoLogic S should be the primary heat producer and

receive the start signal before the boiler.

The settings must be adjusted to minimise the need for additional energy. This is done by

setting the heat pump’s heat curve a few degrees higher than the existing boiler’s heat curve.

To optimise the heating circuit, these settings should be subsequently ﬁne-tuned for optimal

functionality under different operating conditions.

Note that EcoLogicS and the heat pump should be considered supplementary to the existing

heating system in terms of safety functions such as additional heat and backup heating

thermostat. These functions will be retained in the existing heating system.

2.1.1 Heat pump for existing heating system (without 3-way

valve)

System description

This type of connection allows a ground source or air/water heat pump to be added to the

existing heating system consisting of, for example, heat pump (exhaust air, ground source),

electric boiler, wood boiler, oil boiler or pellet boiler.

Conditions

The heat pump must be installed, in terms of ﬂow, before the existing heating system.

Preferably by interrupting the return ﬂow from the heating circuit.

Figure: Example of system solution with

heating system without 3-way valve

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CTC Union Wärmepumpe Handbücher

CTC Union

CTC Union 406 Handbuch

CTC Union

CTC Union CLWi Bedienungsanleitung

CTC Union

CTC Union EcoAir 115 Bedienungsanleitung

CTC Union

CTC Union EcoPart 400 400V 3N Handbuch

CTC Union

CTC Union EcoPart Pro Series Handbuch

CTC Union

CTC Union EcoZenith i555 Pro Series Handbuch

CTC Union

CTC Union EcoAir 500M Handbuch

CTC Union

CTC Union CombiAir 6-UK 1x230V Bedienungsanleitung

CTC Union

CTC Union EcoAir 500M Handbuch

CTC Union

CTC Union EcoAir 500M Handbuch

CTC Union

CTC Union EcoPart XL 434 Handbuch

CTC Union

CTC Union EcoPart 600M Bedienungsanleitung

CTC Union

CTC Union GS 600 Handbuch

CTC Union

CTC Union GSi 16 Handbuch

CTC Union

CTC Union 406 Handbuch

CTC Union

CTC Union EcoAir 500M Handbuch

CTC Union

CTC Union GSi-12 BE Handbuch

CTC Union

CTC Union GSi Series Bedienungsanleitung

CTC Union

CTC Union CTC GS 600 Handbuch

CTC Union

CTC Union CombiAir MR Bedienungsanleitung

CTC Union

CTC Union CombiAir 6MR Benutzerhandbuch

CTC Union

CTC Union EcoHeat 400 Handbuch

CTC Union

CTC Union EcoAir 400 Handbuch

CTC Union

CTC Union GSi 12 Handbuch

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung