CTR Electronics PDP Bedienungsanleitung

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 1 3/28/2018

Power Distribution Panel

User’s Guide

Revision 1.6

Cross The Road Electronics

www.crosstheroadelectronics.com

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 2 3/28/2018

Table of Contents

1. Power Distribution Panel at a Glance..................................................................................... 4

1.1. Connection Specifications ............................................................................................... 5

1.2. Electrical Specifications................................................................................................... 6

1.3. Mechanical Specifications ............................................................................................... 6

1.4. Communication Specifications......................................................................................... 6

2. Installing a PDP ..................................................................................................................... 7

2.1. Battery harness ............................................................................................................... 7

2.1.1. Split Washer.............................................................................................................. 8

2.2. Breakers.......................................................................................................................... 9

2.2.1. Snap Action 40 Amp Breaker.................................................................................... 9

2.2.2. Snap Action 20/30 Amp Breaker..............................................................................10

2.3. Weidmuller Connectors ..................................................................................................11

2.3.1. roboRIO, PCM, VRM................................................................................................12

2.3.2. CAN bus ..................................................................................................................13

2.4. Blade Fuse.....................................................................................................................14

2.4.1. Blade Fuse Replacements.......................................................................................15

2.5. WAGO OperatingTool.....................................................................................................15

3. LED States............................................................................................................................16

4. Functional Limitations (software)...........................................................................................17

4.1. Firmware <1.40: If Robot Is Enabled/Disabled/Enabled Quickly, FRC robot may

momentarily disable...............................................................................................................17

4.2. Firmware <1.40: Power and Energy ...............................................................................17

4.3. LabVIEW: Energy signal is not scaled to Joules.............................................................17

4.4. C++/Java: Energy signal is in Millijoules.........................................................................17

4.5. Firmware <1.37: Current may read ~2A when there is no current...................................17

4.6. FRC2016 roboRIO: CAN Device does not appear in web page diagnostics. ..................18

4.7. FRC 2018: CTRE CAN Receive Timeout........................................................................19

5. Troubleshooting Tips and Common Questions......................................................................20

5.1. What is the threshold for Vbat fault?...............................................................................20

5.2. Are sticky faults cleared during/after a firmware field-update?........................................20

5.3. Do I need to firmware-update? Where are the files?......................................................20

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 3 3/28/2018

TO OUR VALUED CUSTOMERS

It is our intention to provide our valued customers with the best documentation

possible to ensure successful use of your CTRE products. To this end, we will

continue to improve our publications, examples, and support to better suit your

needs.

If you have any questions or comments regarding this document, or any CTRE

product, please contact support@crosstheroadelectronics.com

To obtain the most recent version of this document, please visit

www.ctr-electronics.com.

6. Revision History....................................................................................................................21

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 4 3/28/2018

1. Power Distribution Panel at a Glance

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 5 3/28/2018

1.1. Connection Specifications

●Battery

○Bushings Lugs x 2

○Thread M6x1 (10mm Length)

●Power Channels (All Channels provide battery power)

○WAGO Connectors

■8 Red Channels 4-11

●30 Amp

■8 Red Channels 0-3, 12-15

●40 Amp

■Black terminals are common

○6 Position Weidmuller Connector

■PCM, VRM Supply

●20 Amp fused (ATM blade mini fuse)

■roboRIO Supply

●10 Amp fused (ATM blade mini fuse)

■Max: 16 AWG

■Min: 24 AWG

See Section 2.3. Weidmuller Connectors for wire insert instructions.

●CAN

○4 Position Weidmueller Connector

■Yellow CAN High x 2

■Green CAN Low x 2

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 6 3/28/2018

1.2. Electrical Specifications

Input Voltage (Vbat)

5.5-16 V

Absolute Max Input Voltage(1)

0 - 20 V

Output Voltage

●Channels 0-3, 12-15

Vbat - 40 A

●Channels 4-11

Vbat - 20 or 30 A

●VRM, PCM Weidmuller

Vbat - 20 A fused

●Controller Weidmuller

Vbat - 10 A fused

Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a

stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation

listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.

1.3. Mechanical Specifications

Length

7.586 in.

Width

4.748 in.

Height

1.422 in.

Weight

1 lb. 5.3 oz.

1.4. Communication Specifications

Baud Rate

1 MB/s

CAN Termination

120 Ohm (jumper placed in the ON position).

None (jumper missing or placed in the OFF

position).

CAN High / Low

2 Ports

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 7 3/28/2018

2. Installing a PDP

2.1. Battery harness

●Components

○QTY 2 - M6x1 Bolts (10mm Length) Socket Head Cap Screws

○QTY 2 - 6mm Split (Lock) Washers

○Battery Cover

■QTY 2 - 6-32 (1/2” Length) Battery Cover Flat-Head Socket Cap Screw

○12 Volt Supply (Battery, Power Supply, etc...)

Warning:Do not reverse the battery voltage as this can cause permanent damage to

current sense circuitry. Additionally the FRC Control System Components that

draw power from PDP may not have reverse battery protection, and can also be

damaged in a reverse battery event.

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 8 3/28/2018

2.1.1. Split Washer

Warning:Care should be taken to ensure the split washers are installed under the

screw head. If this is not done, the robot could exhibit several forms of power/brownout

issues as the cable harness loosens over time.

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 9 3/28/2018

2.2. Breakers

2.2.1. Snap Action 40 Amp Breaker

●Channels 0-3, Channels 12-15

○40 Amp Breaker

○Limits Closest Red WAGO

○Supplies Battery Power

Warning: Inductive loads (motor, compressor) must have a power management device

(motor controller, PCM, spike) between itself and the PDP. No inductive loads (motor,

compressor) may be directly connected to the PDP channels as this can damage current

sense circuitry.

PDP User’s Guide

3/28/2018

Cross The Road Electronics Page 10 3/28/2018

2.2.2. Snap Action 20/30 Amp Breaker

●Channels 4-11

○30 or 20 Amp Breaker

○Limits Closest Red WAGO

○Supplies Battery Power

Warning: Inductive loads (motor, compressor) must have a power management device

(motor controller, PCM, spike) between itself and the PDP. No inductive loads (motor,

compressor) may be directly connected to the PDP channels as this can damage current

sense circuitry.

Inhaltsverzeichnis

Andere CTR Electronics Stromverteilungseinheit Handbücher

CTR Electronics

CTR Electronics Pigeon 2.0 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung