CTS EPS-3128 Series Bedienungsanleitung

EPS-3128 Series

24 PoE+ 10/100/1000BASE-T RJ-45 PORTS WITH 4

COMBO PORTS (10/100/1000BASE-T,

100/1000BASE-X SFP) UPLINK MANAGEMENT

SWITCH

User’s Guide

Version 0.90

FCC Warning

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed



to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to

correct the interference at their own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate

measures.

Trademarks

CTS is a registered trademark of Connection Technology Systems Inc

All trademarks belong to their respective proprietors.

Contents are subject to change without prior notice.

This publication may not be reproduced as a whole or in part, in any way

whatsoever unless prior consent has been obtained from Connection

Technology Systems Inc.

Revision History

Version

Date

Description

0.90

20160124

First release

Table of Contents

1. INTRODUCTION ...........................................................................................5

1.1 The Managed Switch................................................................................5

1.2 Key Features............................................................................................6

1.3 Front & Rear Panel...................................................................................7

1.4 Cable Specifications.................................................................................9

1.5 Network Management ..............................................................................9

2. INSTALLATION ........................................................................................... 11

2.1 Requirement........................................................................................... 11

2.2 Checking the Package Contents............................................................ 11

2.3 Install the Managed Switch.....................................................................12

2.4 Power ON...............................................................................................14

2.5 Connect the Switch to network...............................................................15

3. OPERATION................................................................................................16

3.1 LED Definitions.......................................................................................16

4. MAINTENANCE ..........................................................................................17

4.1 Fault Identification ..................................................................................17

4.2 Hardware Replacement Procedures ......................................................19

4.3 Firmware Upgrade..................................................................................19

1. INTRODUCTION

The Managed Switch is designed to meet the emerging FTTX & Metro Ethernet

requirement. Its low profile appearance with 1U height and standard rack-

mount size achieves the highest density within a single rack. When massive

fiber ports need to be deployed, the Managed Switch provides the best

performance and price ratio.

1.1 The Managed Switch

This Managed Switch is compact 19-inch, rack mountable, has 24 PoE+

10/100/1000BASE-T RJ-45 ports with 4 combo ports (10/100/1000Base-T,

100/1000Base-X SFP) in front panel. This Managed Switch provides high

performance store and forward switching plus other advanced features such as

QoS, VLAN, etc.

Clear, at-a-glance per-port LED indicators make users easier to control and

manage network status. Built-in management module also allows users to

configure, control and monitor the system locally via console or remotely via

SNMP based management system.

This Managed Switch is a typical suit for the SFP to Metro Ethernet application.

Its low profile appearance with 1U height achieves the highest density and can

be used in closet wiring or used as a desktop switch.

1.2 Key Features

19 inch, 1U high

24 x 10/100/1000BASE-T RJ-45 ports

-IEEE 802.3/802.3u/802.3ab/802.3z compliance

-Support MDI/MDIX/Auto-Crossover

-IEEE802.3at/af PoE/PSE

-Event Scheduling

4 x 10/100/1000Base-T ,100/1000Base-X Combo ports

-IEEE 802.3ab/802.3z

-Support Auto-Negotiation (RJ-45) and Auto-Sensing (SFP)

-Support MDI/MDIX/Auto-Crossover

-RJ-45 or SFP Slot

Features

-MAC Address Table: 16K

-Non-Blocking Switching Fabric: 56Gbps

-Memory Buffer: 1536K Bytes

-VLAN Groups: 2K VLAN Groups

-Priority Queues: 8 Queues

-Jumbo Frame: 9K Bytes

-Store and Forward Switching Mechanism

-Auto-Cross Over for MDI/MDIX in TP Ports

-Auto-Negotiation in TP Ports

-Full/Half Duplex Mode Operation

-PoE Power Output: 30W max. (per PoE port)

-Max PoE Power Budget

For 480W model: 480Watts at 40°C, 420Watts at 50°C

For 240W model: 240Watts at 40°C, 210Watts at 50°C

-Unknown Unicast/Multicast Flood Control

-Broadcast Storm Control

-IEEE 802.1p with 8 Hardware Priority Queues

-IEEE 802.1Q Tag-Based and Port-Based VLAN

-Q-in-Q

-Weighted Round-Robin (WRR)/Strict-Priority

-Queuing (SPQ) Scheduling Algorithm

-Policy Based Rate Limiting

-Port Based Traffic Shaping

-Static Multicasting

-IGMP v1/v2/v3 Snooping

-IGMP Fast Leave

-IGMP Filtering via Filtering Profile

-MLD v1/v2 Snooping

-Multicast Channel Limitations per Port

-Multicast VLAN Registration (MVR) **

-IEEE 802.3ad Link Aggregation (LACP)

-Static port Trunking

-Up to 14 Aggregation Groups, 8 Ports per Group

-Spanning Tree Protocol (STP)

-Rapid Spanning Tree Protocol (RSTP)

-Layer Link Discovery Protocol (LLDP)

-SFF-8472 (Digital Diagnostic Management Interface for SFP)

-IEEE 802.1X Authentication

-RADIUS Authentication for 802.1X

-DHCP Relay Agent with Option 82

-IP Source Guard (Static IP, DHCP Snooping)

-DHCP Server Trust Port

-Loop Detection

-PoE Management

-Port Isolation

-Port Mirroring

-ACL Based on Physical port, IEEE802.1p, VID, TOS/DSCP,

Ethertype, Protocol Type and L4 Port

-Wire Speed Rate Limiting per MAC/IP/TCP/UDP

-IPv6 over Ethernet (RFC 2464)

-IPv6 Addressing Architecture (RFC 4291)

-IPv6 Dual Stack (RFC4213)

-ICMPv6 (RFC4884)

-Path MTU Discovery for IPv6 (RFC 1981)

-Neighbor Discovery (RFC4861)

-DHCPv6 Client

-SNTP, Daylight Saving

-Time Range

-DHCP Client and Auto-Provision

-Text Based Configuration

-FTP, TFTP, HTTP Firmware & Configuration Upgrade

-Web, SNMP, SSHv2 and Telnet Console CLI Management

-RADIUS Client for Web, CLI

-TACACS+ **

-SNMP v1/v2c - Private, RFC-1213, RMON MIBs

-Event Log, Syslog

**Coming Soon

1.3 Front & Rear Panel

Front Panel

The front panel is configured as follows:

1. 4 x Gigabit combo ports (Ports 25-28) :

4 x 10/100/1000Base-T RJ-45 ports, or

4 x 100/1000Base-X SFP ports

2. 24 x 10/100/1000BASE-T RJ-45 ports (Ports 1-24)

24 x 10/100/1000 PoE ports

3. LED:

Please refer to chapter 3.1 LED Definitions

4. Reset Button:

Pressing reset button for 5~10 seconds then release to restart

the system.

Pressing reset button for more than 10 seconds then release to

reset the Managed Switch back to factory settings and restart

the system.

5. Console port:

An asynchronous serial console port supporting the RS-232

electrical specification. The console port can be used to

manage the device and the interface should be configured to

9600 , N , 8 ,1

Rear Panel

The Managed Switch features one fixed AC power module and its rated input

supply voltage is from AC 110 to 240V, 50/60Hz.

The rear panel is configured as follows:

1. AC inlet

The rated input supply voltage is from AC 110 to 240V, 50/60Hz

2. Power Switch

3. Grounding Wire Screw

Note: Grounding helps to limit the effects of noise due to electromagnetic

interference (EMI). Be sure to install the ground connection from the ground

screw to the grounding surface before connecting devices with lighting

protector.

1.4 Cable Specifications

The following table contains various cable specifications for the Managed

Switch. Please make sure that you use the proper cable when connecting the

Managed Switch.

Cable Type

Description

10Base-T

UTP Category 3, 4, 5 (100 meters max.)

EIA/TIA- 568 150-ohm STP (100 meters max.)

100Base-TX

UTP Cat. 5 (100 meters max.)

EIA/TIA-568 150-ohm STP (100 meters max.)

1000Base-T

UTP Cat. 5e (100 meters max.)

UTP Cat. 5 (100 meters max.)

EIA/TIA-568B 150-ohm STP (100 meters max.)

100BASE-FX

Multi-mode fiber module(2km) / Single-mode fiber module

1000BASE-SX

Multi-mode fiber module (550m)

1000BASE-LX

Single-mode fiber module (10km)

1000BASE-LH

Single-mode fiber module (30km/50km)

1000BASE-ZX

Single-mode fiber module (80km)

Mini-GBIC

SFP Transceiver for 1000BASE-SX Multi-mode fiber module (550m)

SFP Transceiver for 1000BASE-LX Single-mode fiber module (10km)

SFP Transceiver for 1000BASE-LH Single-mode fiber module

(30km/50km)

SFP Transceiver for 1000BASE-ZX Single-mode fiber module (80km)

1.5 Network Management

This Managed Switch is Plug & Play compliant. Real-time operational status

can be monitored through a set of LED indicators located in the front panel.

Built-in management module also allows users to configure, control and monitor

the system remotely.

Following is a list of management options available in this Managed Switch:

Local Console Management

Telnet Management

SNMP Management

Web Management

Local Console Management

Users may connect a Terminal or PC with Terminal Emulation program, to the

Manage---to configure,

control and monitor the system. This is often referred as Out-Of-Band

management.

Console management is useful when there is no network connection to the

Switch, for instance configuring the Managed Switch for the first time.

Telnet Management

Telnet is done through the network. Once there is a network connection to the

Managed Switch, users can use Telnet to configure, control and monitor the

system. Using network connection to manage is often referred to In-Band-

Management.

SNMP Management

SNMP is also In-Band-Management and requires a network connection to the

Managed Switch. The Managed Switch private Management Information Bases

(MIB) is provided for SNMP-based network management program to configure,

control and monitor the system.

Web Management

Web Management is done over the network. Once the Managed Switch is

available on the network, you can login and monitor the status of it through a

web browser remotely or locally. Local console-type Web management,

especially for the first time use of the Managed Switch to set up the needed IP,

can also be done through one of the 10/100/1000Base-T 8-pin RJ-45 ports

located on the front panel of the Managed Switch. Direct RJ-45 LAN cable

connection between a PC and the Managed Switch is required for this

management.

Please refer to the Network Management Users Manual for the detailed

management functions and required installation and operation procedures.

Andere Handbücher für EPS-3128 Series

Inhaltsverzeichnis

Andere CTS Schalten Handbücher

CTS

CTS IES-3006 Series Bedienungsanleitung

CTS

CTS FOS-5112 Bedienungsanleitung

CTS

CTS ESW-5112-2MG Series Bedienungsanleitung

CTS

CTS EPS-3128 Series Bedienungsanleitung

CTS

CTS FOS-3114 Series Bedienungsanleitung

CTS

CTS WAS-2006 Series Bedienungsanleitung

CTS

CTS HES-5106 Series Bedienungsanleitung

CTS

CTS FOS-3124-BAT-II Series Bedienungsanleitung

CTS

CTS HES-3106SFP-F2 Bedienungsanleitung

CTS

CTS IPS-3006 Series Bedienungsanleitung

CTS

CTS FOS-3110 Series Bedienungsanleitung

CTS

CTS FOS-3128 Series Bedienungsanleitung

CTS

CTS IPS-3120-PoE++ Bedienungsanleitung

CTS

CTS FOS-5126 Series Bedienungsanleitung

CTS

CTS FOS-5128 Series Bedienungsanleitung

CTS

CTS SWH-2108 Bedienungsanleitung

CTS

CTS FOS-5152 Series Bedienungsanleitung

CTS

CTS SWH-2109FX Bedienungsanleitung

CTS

CTS ESW-3128 Series Bedienungsanleitung

CTS

CTS HES-3106-PLUS Series Bedienungsanleitung

CTS

CTS WPS-2006 Series Bedienungsanleitung

CTS

CTS EPS-3112 Bedienungsanleitung

CTS

CTS HES-3106 Series Bedienungsanleitung

CTS

CTS ESW-5128 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung