CUMMINS ALLISON JetScan 150 Bedienungsanleitung
| | 1
Getting started
JetScan®150
Currency scanner
User guide
2 | JetScan®150 currency scanner | Safety information, power specications
Safety information, power specications
High voltage inside. Risk of electric shock.
Turn power OFF and unplug power cord from machine before
cleaning.
Do not attempt repairs. Repairs must be made by authorized
Cummins Allison personnel.
Use grounded plug and properly grounded outlet.
Read and understand all instructions before use.
Improper voltage levels can cause equipment malfunction,
damage electrical components, and void warranty.
Provide separate circuit serving only this device and follow listed
power requirements to ensure proper operation.
Provide power conditioning/stabilizing devices if necessary.
• Voltage operating range: 100-240V
• Frequency: 50/60 Hz
• Full load amps (FLA): 2.4A at 100V, 1A at 240V
• Electrical supply circuit: The customer must provide a single-phase, dedicated power line that meets the
machine’s power requirements. Use a properly grounded circuit breaker in compliance with applicable local
electrical code.
Environmental operating conditions
• Temperature: 60°F - 85°F (15°C - 29°C)
• Humidity: 30% to 70% (non-condensing)
Compliance acknowledgments
• FCC: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
• Regulatory: UL/CUL/CE.
Service information for internal fuse
For continued protection against risk of re, replace only with
same type and rating of fuse.
Do not attempt repairs. Repairs must be made by authorized
Cummins Allison personnel.
About this guide | JetScan®150 currency scanner | 3
About this guide
The JetScan®150 currency scanner processes U.S. and international banknotes.
The machine features:
• A fully functioning pocket and a reject pocket to promote a non-stop processing
environment.
• Selectable operating modes which include the ability to detect stranger documents and
target denominations.
• Counterfeit detection.
• Facing and orientation functions.
• Congurable strap limits.
• Cumulative counting.
• A setting for recounting documents without impacting totals.
For information on options and device conguration, contact a Cummins Allison
representative.
Table of contents
Safety information, power specications.................................................................................. 2
About this guide ......................................................................................................................... 3
Machine diagram ....................................................................................................................... 4
Getting started ........................................................................................................................... 7
Stopping conditions and recovery steps.................................................................................14
Daily cleaning procedures .......................................................................................................16
ECB certication software version
To verify European Central Bank (ECB) certication software version:
1. Press CRNCY on the main screen.
2. Press EUR. (EUR currency pattern is an option.)
3. Revision level appears above EXIT.
4 | JetScan®150 currency scanner | Machine diagram
Machine diagram
Reject
pocket
Stacker
wheels
Touch-panel
display
Power switch
(on back
of unit)
Adjustable
hopper guides
Hopper
Thickness adjustment dial located
behind hopper extension
Pocket
sensors
Pocket
Machine diagram | JetScan®150 currency scanner | 5
Communication port diagram
Communication ports are located on the back of the machine.
Only connect LAN/Ethernet cable to LAN/Ethernet port.
Use of any other cable may damage equipment.
Hopper
Machine is auto-start capable. Feed rollers in hopper rotate
inward.
Entanglement and drawing-in hazard.
Do not operate with exposed long hair, neckties, jewelry or loose
clothing.
USB H
LAN/Ethernet
PC
Debug
Display
Printer
The hopper is the area on the top of the machine where notes are placed for processing.
If the machine is congured to auto-start, the rollers and wheels begin moving as soon as
the machine detects notes in the hopper.
6 | JetScan®150 currency scanner | Machine diagram
Thickness adjustment dial
Upper and lower transport sections
The dial located on top of the machine adjusts the tightness of the feeder through which
notes pass during operation. The dial has positive and negative adjustment numbers, with
0at the center of the adjustment range.
For normal feeding, start with 0at the top of the dial.
To help reduce the occurrence of doubles or chains, turn the dial to the right, so
a negative number is at the top, decreasing the distance between the rollers.
Turning the dial to the left, so a positive number is at the top, increases the
spacing between the rollers, allowing notes to pass through more easily.
The upper and lower transport sections must be opened for jam recovery and cleaning.
To open the upper transport, lift the latch below to release and raise the section to the
locked position. To close the section, guide it to its operating position and press to lock it
in place.
To open the lower transport, pinch the two tabs below to release and lower the section.
To close the section, guide it to its operating position and press to lock it in place.
Getting started | JetScan®150 currency scanner | 7
Getting started
High voltage inside. Risk of electric shock.
Turn power OFF and unplug power cord from machine before
cleaning.
Do not attempt repairs. Repairs must be made by authorized
Cummins Allison personnel.
Use grounded plug and properly grounded outlet.
Read and understand all instructions before use.
Powering ON/OFF
To turn the machine ON, set the rocker switch located in the lower-left rear corner when
facing the front of the machine to the ON position (I). Allow the machine to complete its
power-on sequence. The machine is ready to process notes when the touch panel displays
the main screen.
To turn the machine OFF, ensure the machine is not processing notes, and then set the
rocker switch located on the rear of the machine to the OFF position (O).
This section outlines basic features and functions of the JetScan 150 currency scanner.
8 | JetScan®150 currency scanner | Getting started
Touch-panel display: Main screen
Main screen key Description
CRNCY
Press to prompt the SELECT NEW CURRENCY screen
and activate the preferred currency for processing.
CRNCY may appear on the main screen or MAIN SUB-
MENU, depending on the conguration in SETUP.
VERIFY
Press to enable the verify function, which allows notes
to be processed off-line.
This function can be used to recount and reconcile
any count suspected of being wrong without adding to
current batch or day totals.
When VERIFY is pressed, machine totals return to zero,
and the machine processes notes following rules of the
indicated mode.
When VERIFY is pressed again (to exit the function),
the machine returns to the operating mode, as well as
totals and settings, that were previously active.
DETAIL Press to prompt the VALUE DETAIL screen for a
denominational breakdown of the batch totals.
ADD
Press to enable or disable the ADD function. When
enabled, batch totals accumulate after notes are
removed from the pocket.
END Press to clear current batch totals.
Getting started | JetScan®150 currency scanner | 9
Main screen key Description
CONT Press to start the motor.
MANUAL
Press to prompt a screen that is used to input mutilated
notes that could not be processed.
Press ADD and then press the specic denomination to
enter the value of a note. Press ADD repeatedly to enter
that note more than once.
Press SUB to remove a note’s value from the screen.
Press SUB repeatedly to remove a note’s value more
than once.
REJECT REASON Press to prompt a screen displaying all rejected notes
and their respective error codes.
TOTALS
Press to prompt a screen displaying three levels of
accumulated totals: TOTALS, SUB TOTALS and GRAND
TOTALS.
These categories can be dened for any level of
tracking, such as teller (TOTALS), shift (SUB TOTALS)
and day (GRAND TOTALS) reporting.
STRAP Press to prompt the STRAP SETTINGS screen, where
strap limits are set.
MODE Press to prompt the MODE SELECTION screen, which
displays all processing modes.
MENU
Press to prompt the MAIN SUB-MENU, which provides
access to additional menus.
Press OLD/NEW on the MAIN SUB-MENU to enable
series separation. The rst note processed determines
the series. All other series of that denomination (STRGR
mode) or denominations (MIX mode) will be rejected
and uncounted.
10 | JetScan®150 currency scanner | Getting started
Operating modes
Mode key Description
STRGR
(STRANGER)
Scans for the rst denomination processed (target), and
diverts all other denominations to the reject pocket. A
grand total is provided.
MIX Scans all denominations without presorting. A grand
total by denomination is provided.
COUNT
Counts any type of media that complies with document
size and density-setting specications.
This mode only counts pieces; document scanning does
not occur.
FACE
When FACE is selected in addition to STRGR or MIX
mode, the machine diverts non-faced notes to the reject
pocket. The rst note processed determines the facing.
Pressing MODE from the main screen displays all modes available for use.
Inhaltsverzeichnis
Andere CUMMINS ALLISON Banknotenzähler Handbücher
Beliebte Banknotenzähler Handbücher anderer Marken
Safescan
Safescan 2660-S Bedienungsanleitung
PRO Intellect Technology
PRO Intellect Technology PRO 95U Bedienungsanleitung
Dors
Dors 600 Bedienungsanleitung
radiotec
radiotec rapidcount S 575 Bedienungsanleitung
PRO Intellect Technology
PRO Intellect Technology 40 NEO Bedienungsanleitung
Conrad
Conrad 75 17 78 Bedienungsanleitung
Total
Total M2300U Schulungshandbuch
Double Power Electronics
Double Power Electronics DP-8120VB Bedienungsanleitung
ratiotec
ratiotec Soldi Smart Plus Gebrauchs- und Pflegehandbuch
Olympia
Olympia NC 455 Bedienungsanleitung
Plaisio
Plaisio Q-CONNECT QCD11 Bedienungsanleitung
Royal Sovereign
Royal Sovereign RBC-1003BK Bedienungsanleitung