Custom Audio Electronics XD Bedienungsanleitung
POS
USER MANUAL
MINI
MINI
XD
XD
CUSTOMER
CUSTOMER
DISPLAY
DISPLAY
All rights reserved. Total or partial reproduction of this manual in whatever form, whether by printed or elec-
tronic means, is forbidden. While guaranteeing that the information contained in it has been carefully checked,
CUSTOM ENGINEERING SPA and other entities utilized in the realization of this manual bear no responsibility
for how the manual is used.
Information regarding any errors found in it or suggestions on how it could be improved are appreciated. Since
products are subject to continuous check and improvement, CUSTOM ENGINEERING SPA reserves the right
to make changes in information contained in this manual without prior notification.
Copyright © 2008 CUSTOM ENGINEERING S.p.a. – Italy
CUSTOM ENGINEERING S.p.A.
Str. Berettine 2 - 43010 Fontevivo (PARMA) - Italy
Tel.: +39 0521-680111 - Fax: +39 0521-610701
http: www.custom.it
Customer Service Department:
Tel.: +39 059 88 69 587
Email: [email protected]
GENERAL FEATURES
A new family of customer displays with a clear-cut, modern and elegant design enhanced by the blue back-
lighting of the 2-line x 20-character display. The new support system makes the display easy to position and
offers two different display heights. The XD is available in single- and double-sided versions and can be
incorporated in the body of Custom printers.
Nice and modern design customer display•
Single or double side•
Blue colour backlighted display•
Easy view angle adjustment•
Low and high version available•
DISPLAY+ PRINTER COMPONENTS
1 Display 2*
2 Display 1
3 Horizontal adjustment
4 Inclination angle adjustment
5 Base
6 Communication cable
* Only double-side display.
(Fig.1)
1
2
3
4
6
User Manual XD CUSTOMER DISPLAY
DISPLAY COMPONENTS
1 Display 2*
2 Display 1
3 Horizontal adjustment
4 Inclination angle adjustment
5 Base
6 Communication cable
* Only double-side display. (Fig.2)
(Fig.3)
1
5
2
3
4
6
1
5
2
3
4
6
XD CUSTOMER DISPLAY User Manual
INTRODUCTION
MANUAL CONTENTS......................................................................................................................................1
EXPLANATORY NOTES USED IN THIS MANUAL .........................................................................................1
GENERAL SAFETY INFORMATION................................................................................................................1
UNPACKING THE DISPLAY ............................................................................................................................2
1. INSTALLATION AND USE
1.1 DISPLAY MOUNTING .............................................................................................................................1-1
1.2 CONNECTIONS......................................................................................................................................1-2
1.2.1 RS232 Serial Interface and power supply .......................................................................................1-2
1.3 SELF-TEST .............................................................................................................................................1-3
1.4 MAINTENANCE ......................................................................................................................................1-4
1.4.1 Display adjustments ........................................................................................................................1-4
1.4.2 Cleaning the customer display ........................................................................................................1-5
2. DISPLAY FUNCTIONS
2.1 COMMAND DESCRIPTIONS..................................................................................................................2-1
2.1.1 ESC/POS Emulation .......................................................................................................................2-1
2.1.2 CD5220 Emulation ........................................................................................................................2-14
3. TECHNICAL SPECIFICATIONS
3.1 TECHNICAL SPECIFICATIONS..............................................................................................................3-1
3.2 DIMENSIONS..........................................................................................................................................3-2
3.2.1 Low version display (single / double side).......................................................................................3-2
3.2.2 High version display (single / dopuble side) ....................................................................................3-3
3.2.3 High version display + printer (single / dopuble side)......................................................................3-4
4. CHARACTER SET
4.1 CHARACTER SET ..................................................................................................................................4-1
APPENDIX A - ACCESSORIES AND SPARE PARTS
A.1 ACCESSORIES ..................................................................................................................................... A-1
A.1.1 Stand Alone Kit for customer display ............................................................................................. A-1
TABLE OF CONTENTS
User Manual XD CUSTOMER DISPLAY i
Blank page
TABLE OF CONTENTS
ii XD CUSTOMER DISPLAY User Manual
MANUAL CONTENTS
In addition to the Introduction which includes a description of the explanatory notes used in the manual, general
safety information, how to unpack the display and a brief description of the display including its basic features,
this manual is organized as follows:
Chapter 1: Contains the information required for correct display installation and its proper use
Chapter 2: Contains a description of the display command set
Chapter 3: Contains Technical Specifications of the display
Chapter 4: Contains the character sets (fonts) used by the display
EXPLANATORY NOTES USED IN THIS MANUAL
N.B.
Gives important information or suggestions relative to the use of the display.
WARNING
Information marked with this symbol must be carefully followed to guard against damaging the
display.
DANGER
Information marked with this symbol must be carefully followed to guard against operator injury
or damage.
GENERAL SAFETY INFORMATION
• Read and keep the instructions which follow.
• Follow all warnings and instructions indicated on the display.
• Before cleaning the display, disconnect the power supply.
• Clean the display with a damp cloth. Do not use liquid or spray products.
• Do not operate the display near water.
• Do not use the display on unstable surfaces that might cause it to fall and be seriously damaged.
• Only use the display on hard surfaces and in environments that guarantee proper ventilation.
• Make sure the display is placed in such a way as to avoid damage to its wiring.
• Use the type of electrical power supply indicated on the display label. If in doubt, contact your retailer.
• Do not introduce foreign objects of any kind into the display as this could cause a short circuit or damage
parts that could jeopardize display functioning.
• Do not spill liquids onto the display.
• Do not carry out technical operations on the display, with the exception of the scheduled maintenance
procedures specifically indicated in the user manual.
• Disconnect the display from the electricity supply and have it repaired by a specialized technician when:
A. The feed connector has been damaged.
B. Liquid has seeped inside the display.
C. The display has been exposed to rain or water.
D. The display is not functioning normally despite the fact that all instructions in the users manual
have been followed.
E. The display has been dropped and its outer casing damaged.
F. Display performance is poor.
G. The display is not functioning.
INTRODUCTION
User Manual XD CUSTOMER DISPLAY 1
4 5 62 31
UNPACKING THE DISPLAY
Remove the display from its carton being careful not to damage the packing material so that it may be re-used
if the display is to be transported in the future. Make sure that all the components illustrated below are present
and that there are no signs of damage. If there are, contact Customer Service.
1. Fixing screw + washer User manual
2. Display group
3. Box
4. Base
5. Installation instructions
6 User manual
Open the display packaging.•
Take out the fixing screw.•
Take out the user manual and the installation instructions.•
Take out the base and the display group.•
Keep the box packing materials in the event the display must be transported/shipped in the future•
(Fig.1)
INTRODUCTION
2 XD CUSTOMER DISPLAY User Manual
1.1 DISPLAY MOUNTING
Insert the display group in the hinge pin of the base. Insert the communication cable inside the hinge pin•
(see Fig. 1.1).
Rotate the display group until it stops (see Fig.1.2).•
Lock the display group using the fixing screw included in the package•
(see Fig.1.3).
13
2
(Fig.1.1)
(Fig.1.3)
(Fig.1.2)
WARNING
Before fastening the commu-
nication cable check the cable
path is correct. Incorrect posi-
tions of the cable could cause
damage on it.
1. INSTALLATION AND USE
User Manual XD CUSTOMER DISPLAY 1-1
1.2 CONNECTIONS
1.2.1 RS232 Serial Interface and power supply
(Fig.1.4)
RJ45
81
The display with a serial RS232 interface has a female RJ45 connector. Refer to the table below for the con-
nector pin signals:
PIN SIGNAL DESCRIPTION
1 TXD - OUT Data transmission
2 RXD - IN Data reception
3 RTS - OUT Ready to receive data
4 CTS - IN Ready to receive data
5 GND Ground signal
6 GND Ground signal
7 +VI Power supply
8 +VI Power supply
NOTE
The information in this page are valid for all the models.
WARNING
For the display version without printer use the power voltage indicated on the product
label.
1. INSTALLATION AND USE
1-2 XD CUSTOMER DISPLAY User Manual
Inhaltsverzeichnis
